• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.36-43
• /
• 1997

To cope with quest to improve the fuel economy and vehicle performance, Continuously Variable Transmission with Changing the speed ratio between minimum and maximum ratio by infinite step, is more efficient than conventional multi-ratio transmission. In this paper, to investigate a specific CVT shift ratio diagram and CVT shift characteristics, CVT vehicle was tested on the proving ground and chassis dynamometer. The test results are as follows; CVT can obtain the excellent vehicle performance and fuel economy changing the shift ratio by infinite step, without rapid change of engine revolution and driving force. And CVT can set up a special shift range that obtains not only the engine brake effect but also the maximum speed driving.

• 기계저널
• /
• 제33권10호
• /
• pp.892-901
• /
• 1993

환경오염과 차량 성능향상에 따라서 날로 강화되는 연비규제는 차량용 변속기로서 CVT 양상 보급에 대한 필요를 앞당기고 있다. CVT는 소형차를 중심으로 일부 자동차 에이커에 의해 이미 실용화되어 있으며 일본 및 구미 자동차 각 사는 CVT에 대한 자체기술을 보유하고 경쟁성 있 는 완성품 개발을 위하여 총력을 기울이고 있는 실정이다. CVT에 대한 연구개발의 추세는 동 력전달 구동요소의 특성에 따라 벨트식과 토로이달 (Torodial)식으로 구분할 수 있으며 대부분의 경우 현재 일부 실용화 개발된 벨트식 CVT가 기술완성도가 높은 반면 토로이달롤러의 각도를 연속적으로 변환시킴으로써 무단변속을 이루는 토로이달 방식은 2000년대 이후에 양산을 목표로 일본 및 영국 등에서 개발 진행주이나 새로운 재질과 제어기술개발 등의 숙제를 안고 있다. 벨 트식의 경우 금속벨트는 지난 십 수년이상 시행착오를 겪으며 CVT용으로 개발된 전문업체의 제품이 이미 특허화되어 있기 때문에 자동차 각사는 벨트와 같은 구동요소보다는 CVT 메카니즘 설계 및 제어시스템 개발에 기술력을 투입하고 있다. 따라서 국내 CVT 개발도 이와 같은 추세를 따를 것으로 기대되고 있으나 AT와 같은 완성품으로서의 상품가치를 갖기 위하여는 CVT에 대한 보다 많은 연구개발이 필요하다고 생각된다.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.111-119
• /
• 1997

In this paper, engine-CVT consolidated control performance were investigated experimentally. Engine-CVT consolidated control was composed of engine throttle control based on power difference and CVT ratio control based on CVT ratio map. Experimental results showed that engine optimal operation was obtained while satisfying the driver's desire, i. e., following the given drive mode by engine-CVT consolidated control. Also, it was found that engine performance is subjected to inertia of the powertrain where the magnitude of acceleration changes abruptyly. Comparing with the results of CVT only control, the results of engine-CVT consolidated control showed better performance. Therefore, in order to meet the driver's desire as well as keeping the engine optimal operation, the engine-CVT consolidated control could be suggested as an integral solution.

• 한국자동차공학회논문집
• /
• 제7권8호
• /
• pp.132-142
• /
• 1999

In this paper, a new formula for primary and secondary thrust of metal belt CVT is proposed considering variation of band tension, block compression and active arc for each of the primary and secondary pulleys. For the secondary thrust, effective friction coefficient is introduced considering the effect of flange deflection. Nondimensional primary and secondary thrust of the metal belt CVT by the new formula agree well with the experimental results except for low torque range, $0\;<\;{\lambda}\;<\;0.2$ at speed ration i = 1.0. The new formula can be used in design of the primary and secondary thrusts control system for the metal belt CVT.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.226-233
• /
• 1998

In this paper, an experimental study was performed to investigate the speed ratio-torque-thrust characteristics for metal belt CVT. It is observed from the experimental results that nondimensional secondary thrust force follows with the existing theoretical formula with ${\mu}$=0.09~0.12 depending on the torque and the speed ratio. In order to represent these characteristics, an effective friction coefficient was introduced. Also, the slip characteristics between the belt and the pulley were investigated experimentally and traction coefficients at gross slip were obtained for various speed ratios. Using the traction coefficients and the effective friction coefficients, an improved formula for the secondary thrust force was suggested assuming that thrust force is the summation of the thrust of pseudo inactive arc and the thrust of pseudo active arc. The effective friction coefficient and the improved formula for the speed ratio-torque-thrust relationship suggested in this work can be used to obtain the appropriate secondary thrust.