• Journal of the Korea Institute of Building Construction
• /
• v.10 no.1
• /
• pp.213-219
• /
• 2010

The research, based on 200 cases of small interior works in6 different floor area types of apartment in Busan, intended to compare the architectural work with the breakdown structure and analyze the cost of general small-scale interior work, by work type. The outcome of the research is outlined as follows. (1) Given the cost of small interior works for apartmentsranges from 10 million to 15 million won, which correspond to apartments ranging in size from $79.2m^2$ (24PY) to $105.6m^2$, it is necessary to implement a cost analysis for material cost and labor cost for these two types. (2) Given that small interior work for apartments comprises mostly finishing work, unlike the categoriesof general architectural work, it is more reasonable to classify the works into 9 categories,which include embellishment, wood, tile, paint, metal, toilet, sink & furniture, electric & mechanical and other works, instead of the 22 divisions stipulated in the Korean Architectural Standard Specification. (3) After reviewing the average cost of small interior work and rate by floor area, it was found thatthe average cost of 24PY was 10.5 million won, of which metal work accounts for 12.8%, embellishment work 17.8%, and toilet 19.7%, while sink & furniture appeared to be the highest with 22.1%, while for 32PY, average cost was 12.5 million won,which comprises 7.4% wood work, sink & furniture 20.2%, toilet 23.4% and embellishment work the highest at 28.6%, indicating that embellishment work accounts for the greater portion.

• Fire Science and Engineering
• /
• v.28 no.5
• /
• pp.8-13
• /
• 2014

The purpose of this study is to analyze the damage pattern when overcurrent is applied to a thermal magnetic type molded case circuit breaker (MCCB) using a Primary Current Injection Test System (PCITS). When an overcurrent of 150 A was applied to the PCITS for 5 seconds with the trip bar of an MCCB being damaged, it was found that the surface of the temperature control device (bimetallic strip) positioned at the right was significantly carbonized. When an overcurrent of 300 A was applied to the PCITS for 5 s under the same conditions, the entire temperature control device was deteriorated, becoming flattened and in close contact with the MCCB. When an overcurrent of 450 A was applied to the PCITS for 5 s, the coil of the temperature control device was melted and disconnected. In addition, it was observed that the contacts, the enclosure and upper cover were deformed and there was a trace of carbonization on them. When approximately 3 s had elapsed after an overcurrent of 600 A was applied, white smoke occurred inside the MCCB and a flame was radiated out, after which the overcurrent supply stopped with "phutt" (whomp) sound. It was observed that when the same type of MCCB is damaged by a general flame, the surfaces of its handle, terminal, arc divider (extinguisher) and temperature control device were carbonized uniformly. In addition, it was found that the trip bar of the operating mechanism was melted down and the metal operation pin was moved while being tripped.

• Journal of Life Science
• /
• v.16 no.4
• /
• pp.605-611
• /
• 2006

To investigate the possible use of probiont in fish farming industry, a bacterium with inhibitory effect against Vibrio anguillarum was isolated from gastrointestinal tract of the marine fish of yellow tail. It was identified to be Bacillus amyloliquefaciens H41 based on biochemical and physiological characterization. The optimal growth conditions of the isolated strain were 1% peptone, 1.5% yeast extract, 1% sucrose, 0.5% NaCl, 0.05% $MgSO_4{\cdot}7H_20$, pH 7.0-8.0, and 20 hr of incubation between $28-35^{\circ}C$ under aeration. The culture supernatant of the isolated strain showed inhibition activity against V. anguillarum. Inhibition activity was cleared by forming a clear zone by a paper-disk method. The maximal production of growth inhibition factor was induced by cultivation under 1% peptone, 1.5% yeast extract, 1% sucrose, 1% NaCl, 0.05% $MgSO_4{\cdot}7H_20$, pH 7.5 and at $35^{\circ}C$. The highest growth inhibition factor production was observed after 16-24 hr cultivation under aeration. The culture supernatant of the isolated strain showed inhibition activity whereas no inhibition activity was shown from the standard B. amyloliquefaciens KCTC 1724 strain. The growth inhibition affected only against V. anguillarum among other pathogenic Vibrios tested here.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1998.05a
• /
• pp.108-108
• /
• 1998

일반적으로 탄소강은 수용액 중에 노출될 경우 전면부식에 의한 손상을 받는다. 그러나 부식방지를 위하여 부식억제제를 적용할 경우, 탄소강의 부식거동은 현저한 변화를 겪게된다. 이러한 부식거동의 변화는 첨가되는 부식억제제의 종류에 따라 분 류할 수가 있는데, 양극부식억제제, 음극부식억제제 그리고 이들의 혼합부식억제제로 분류할 수가 있다. 현장에 적용된 부식억제제 시스템 중에는 자동차용 부동액과 가스히터용 열전달 매체액이 있다. 이러한 부식억제제가 적용된 시스댐은 정확한 부식억제능의 평가에 의한 그 교체 시기의 결정이 매우 중요하다. 교체 시기가 빠를 경우, 유지비용이 과다하게 소요되는 문제가 있으며, 교체시기가 늦을 경우 설비의 부식을 초래하는 문제 가 있다. 따라서 부식억제제의 정확한 성능 평가법은 매우 중요하며, 이에 대한 다양 한 연구가 진행 중이다. 부식억제제가 함유된 용액의 부식억제성능을 평가하는 방법에는 대표적으로 무게 감량법을 이용하고 있다. 이 방법은 다종의 금속이 적용된 자동차용 부동액을 실제 사용조건과 유사한 실험 조건에서 단기간, 가혹조건에서의 무게 감량에 의해 부식억 제능을 평가하는 방법이다. 그러나 이러한 방법은 특히 국부부식이 진행될 경우 부 식억제능을 정량화 하는데 어려움이 있다. 한편 전기화학적 측정방법으로는 분극곡선법을 이용한 $E_P$(공식개시전위), $E_R$(재부동태 화전위)의 측정법이 있다. 또한 부식억제피막의 안정성을 측정하기 위한 방법으로 인 위적인 양극전류 인가에 의한 피막의 파괴후에 피막이 복원가능 여부 및 그 속도 측 정에 의해 부식억제제의 건전성을 확인할 수가 었다. 본 연구에서는 가스히터의 주구성 재료인 A210 Gr Al의 탄소강을 사용하여, 사용기간이 5년 이상되어 부식억제 기능을 거의 상실한 것으로 여겨지는 열전달 매체액 과 신규 부식억제제가 적용된 시스템 등 객관적으로 확인된 부식억제제 시스랩에 대 하여 다양한 평가 방법을 동원 비교분석하고자 하였다. 실험은 KSM 2142에 의한 무게감량법, 분극곡선 측정에 의한 $E_P$(공식개시전위), $E_R$(재부동태화전위) 측정, 시간에 따른 자연전위 변화 측정 빛 이때의 부식속도(선형분극법), 인위적인 피막 파괴 전,후 의 전위 변화 및 부식속도 측정법에 의한 국부부식 발달 저지능 등을 평가하여 각 실험결과를 비교분석하여 보았다.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.8 no.4
• /
• pp.220-226
• /
• 2005

This study evaluated the composition and distribution of marine litters on the sea-bed of the East China Sea. Surveys have been conducted by a benthic trawlnet of Dong-baek training ship of Yosu national university during the cruise of 2002-2004. Distribution density showed high value in C5 (north-western area of Jeju Island) with $110.3kg/km^2$ and those of annual mean were about $31-43kg/km^2$. Fishing gears such as nets, pots, octopus jars and etc. were about 42-72% of debris collected in the East China Sea. Composition ratio of rubber, vinyl. metal, plastic, glass, wood, cloth and etc. were within 25% except C5. Rope and drum showed strong fluctuations with 0-30% according to the trawling sites. Some vinyls and nets made in Korea, China and Japan were much collected. It is estimated that fishing gears were discarded to the sea by fishing operation, deliberately or not. An comprehensive program including continuous research, monitoring for marine litters in the Korean sea were necessary.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.229-229
• /
• 2007

나노결정 합금재료를 전력선 통신 커플러용 자심재료로 응용하기 위해서는 고주파 대역에서의 손실 특성이 제어되어야 한다. 즉 고속 전력선 통신을 위한 자심재료의 투자율 및 완화 주파수 등의 전자기적 특성은 30MHz까지 우수하고 안정적으로 유지되어야 하며, 높은 투자율 및 자속밀도, 공진주파수뿐만 아니라 낮은 전력손실 값을 가져야 한다. 따라서 본 연구에서는 나노결점 합금 리본 표면에 딥 코팅, 졸-겔법, 진공함침 등의 방법을 이용하여 PZT, $TiO_2$ 및 $SiO_2$ 등의 산화물 고저항층을 형성시켜 자기적 성질을 유지하면서 고주파 대역의 와전류 손실을 감소시켜 통신용 자심재료로의 응용성을 향상시키고자 하였다. PZT 슬러리의 제타전위 조절을 통해 최적의 분산조건을 얻을 수 있었고, 평균 150nm인 PZT 입자의 초미립자와 가소제, 분산제, 결합제의 첨가조건을 확립할 수 있었다. 딥-코팅은 슬러리 내 유지시간 10초, 인상속도 5mm/min로 30회 반복되었을 때 가정 우수한 특성을 나타내었으며, 고주파 대역에서의 손실 감소효과를 나타내었다. 그리고 졸-겔법에 의해 제조된 슬러리를 이용한 $TiO_2$와 $SiO_2$ 산화물 저항층 코팅을 통해 금속 알콕사이드의 혼합조건 및 저항층 형성용 슬러리의 제조조건을 확립하였고, 합금 리본표면에 균일하고 우수한 점착력을 가지는 저항층을 형성시킬 수 있었으며, 이에 따른 코어손실의 감소효과를 나타낼 수 있었다. 또한 진공 함침법을 통한 저항층 형성에서, $TiO_2$ 나노분말을 표면 저항층으로 코팅했을 때, 가장 높은 코어손실 감소효과를 나타내었다. 한편, 표면 저항층이 형성된 나노결정 합금으로 제조한 자심재료를 이용하여 전력선 통신용 비접촉식 커플러에의 적용과 시험을 통해 고주파 손실 감소효과에 의한 신호전송 특성과 전류특성을 향상시킬 수 있었다.

• The Journal of Engineering Research
• /
• v.6 no.2
• /
• pp.23-32
• /
• 2004

Metals, ceramics and polymers are widely used as bioimplant materials. However, Ti and Ti alloys are widely used because of its high strength to weight ratio and good biocompatibility when implanted in the body. In this experiment, Ti alloys of Grade-4 (gr4), 0.2 wt % Fe, 0.5 wt % Fe and 2 wt % Fe were studied for their surface morphology and HAp forming ability on the metal substrate for different treatments. Intially, the samples were mechanically polished on silicone carbide paper (No.-2000). The polished samples were treated with 5M NaOH solution at $60^{\circ}C$ for 24 hours. The NaOH treated samples were washed gently with distill water and dried at $40^{\circ}C$ for 1 day. The dried samples were heated in air at $600^{\circ}C$ for 1 hour. The surface morphology of these samples were studied using SEM. The SEM studies showed network of pores in all samples. These samples were immersed in stimulated body fluids (SBF) kept at $36.5^{\circ}C$ for different periods over the length of 1 to 14 days. The apatite formation was confirmed on all Ti-alloys using EDAX.

• Membrane Journal
• /
• v.13 no.3
• /
• pp.143-153
• /
• 2003

The effects of bipolar interface formed on the surface of cation-exchange membrane on water splitting phenomena were investigated. Results showed that the formation of immobilized bipolar interface resulted in significant water splitting during electrodialysis. In particular, the immobilized bipolar interface was easily created on the cation-exchange membrane surface in the electrodialytic systems where multivalent cations served as an electrolyte. Multivalent cations with low solubility product resulted in violent water splitting because they were easily precipitated on the membrane surface in hydroxide form. Therefore, the bipolar interface consisting of H- and OH-affinity groups were formed on the membrane-solution interface. Apparently, water splitting was largely activated with the help of strong electric fields generated between the metal hydroxide layer and fixed charge groups on the membrane surface. Likewise, the accumulation of large molecular counter ions on the membrane surface led to the formation of a fixed bipolar structure that could cause significant water splitting in the over-limiting current region. Therefore, the prevention of the immobilization of bipolar interface on the membrane surface is very essential in improving the process efficiency in a high-current operation.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.67-67
• /
• 2009

알루미늄 합금 재질은 무게의 경량화와 기계적강도가 우수하며 다른 비철금속에 비하여 값이 저렴한 장점이 있다. 현재 산업현장에서 활용하는 가장 흔한 접합법으로 TIG, RSW 등과 같은 용융 용접법을 현재는 많이 사용 하고 있지만 열전도도가 높아 열 확산이 빠르고, 이에 따라 모재의 팽창이 일어나 열변형을 유발하며, 산화피막은 그 내부에 함유된 결정수가 아크용접 중 분해되어 수소를 방출함으로 기공이 발생하여 부도체로 저항용접시 전도성을 방해하는 등의 문제를 발생시킨다. 또한 철에 비해 4배정도 큰 전기전도율에 따라 저항용접시 대전류를 사용해야 하는 등의 문제점이 발생하고 있다. 이와 같은 알루미늄 합금의 용융용접 과정에서 발생하는 단점을 극복하는 기술로 고상접합 방법인 마찰교반용접법(Friction Stir Welding)이 활용되고 있다. FSW는 1991년 영국의 TWI에서 개발된 최신 용접법으로 모재를 용융점 아래에서 고상용접시키는 방법으로 용융에 따른 열변형과 흄가스(hume gas)와 스패터(spatter)를 억제시켜 주는 친환경적인 용접법이다. 이러한 마찰교반용접의 기술은 그동안 특허에 따른 로열티가 산업현장에서 사용하는데 문제가 되었으나 특허보호 기간인 20년이 1년정도의 기간밖에 남지 않은 상황에서 그 사용은 날로 증가하리라 본다. 이러한 마찰교반용접부의 결함을 평가하는 방법에는 UT, RT 등이 활용되고 있으나 얇은 박판에서의 결함검출은 용이하지 않다. 이리한 문제점을 해결하기위하여 초음파 가진을 이용한 적외선 열화상 검출 기법을 이용하여 마찰교반용접부의 결함 검출 가능성을 연구하였다. 20kHz의 주파수를 400Watt로 가진시켜 겹치기(lap joint) 마찰교반용접이된 A6061-T6의 용접부에 초음파를 입사하였을 때 발생하는 열을 적외선 열화상 카메라를 이용하여 측정함으로써 마찰교반겹치기 용접부의 결함 검출에 활용하였다. 용접부에 초음파를 입사하였을 때 부분적으로 온도차이가 발생하였고, 그에 따른 열화상을 검출 할 수 있었다. 이러한 열화상과 실제 시험편의 용접부의 강도를 평가하기 위하여 인장시험을 하였다. 그 결과 초음파 적외선 열화상 검출에서 발열부위가 나타난 부분이 인장시험에서 낮은 인장강도를 보였다.

• Journal of the Korean Institute of Gas
• /
• v.25 no.5
• /
• pp.30-36
• /
• 2021

Residual life assessment of reformer tubes of mod HP steel used in the refinery and petrochemical industry were investigated by quantitative metallographic evaluation method. Area fractions of precipitated carbides were measured by using surface replication and its relationship with the remaining life of the tube was investigated. The microstructures of the virgin and other tubes were examined using optical microscopy (OM) for service periods of 1.8, 6.0, 7.2, 8.5, 9.7, and 16.2 years at 950 ℃ and the area fractions of the precipitates were measured by image analysis using ImageJ software. As the area fraction of the precipitates increased, the residual life was decreased accordingly. The results showed that the LMP was the highest in the virgin and the LMP decreased as the service time increased and the residual life decreased. A regressional equation showing the relation between the area fraction of carbides and LMP was experimentally derived. The obtained relationship can be used with the surface replication method for on-site residual life assessment.