Kim, Dong Won;Kim, Chang Suk;Choi, Ki Young;Jeon, Young Shin;Hong, Choon Pyo
Analytical Science and Technology
/
v.6
no.5
/
pp.471-477
/
1993
The novel macrocylic ligand {(4, 5):(13, 14)-dibenzo-6, 9, 12-trioxa-3, 15, 21, -triazabicyclo [15. 3. 1]heneicosa-(1, 17, 19)(18, 20, 21) triene: HDBPDA} was synthesized, and protonable constants of the ligand and the complex stability constants with alkali metals alkaline earth metals were determined. We evaluated the resolution factor(${\Delta}$) from equation that inducing from stability constants(pK). Also, this ligand was grafted on chloromethylated styrene-divinyl benzene(Merrifield resin) for HDBPDA, ion exchanger. Alkali and alkaline earth metal ions were separated using water by the column chromatography with this ion exchanger. Selectivity(${\alpha}$) and resolution(Rs) of alkali and alkaline earth metal ions were measured from the elution curves chromatogram. The selectivity and resolution values of the various ions calculated from the elution curves were compared with those abtained from pK values. The results were in a good agreement between tow methods. Ion exchange capacity of the resin were determined using the alkali and alkaline earth metal ions and pH dependence of capacity was also discussed.
Many experimental results have revealed that the development of cavitaition during tensile deformation is limited by the Presence of liquid phases. However, the presence of liquid phases does not always lead to high-strain-rate superplasticity, because too much liquid causes intergranular decohesion at grain boundaries/interfaces in metal-matrix composites. Thus, it is important to examine the nature of interfaces of superplastic composites in order to understand the origin of superplastic flow related to liquid grain boundaries during high-strain-rate superplastic deformation. This study shows that a large elongation is obtained at the temperature, that is close to the onset temperature for partial melting in the superplastic composites, but the elongation significantly decreases at slightly higher temperatures, which are close to the end temperature fur partial melting. This indicates that there is an optimum amount of the liquid phase for obtaining high-strain-rate superplasticity in these materials.
This paper addresses recent status and trends of carbon dioxide capture technologies using dry sorbents in the flue gas. The advantages of dry sorbent $CO_2$ capture technology are broader operating temperature range, less energy loss, less waste water, less corrosion problem, and natural properties of solid wastes. Recently, U.S.A. and Korea have been developing processes capturing $CO_2$ from real coal flue gas as well as sorbents improving sorption capacity to decrease total $CO_2$ capture cost. New class of dry sorbents have been developed such as chemisorbents with alkali metals of which material cost is low, amines physically adsorbed on silica supports, amines covalently tethered to the silica support, carbon-supported amines, polymer-supported amines, amine-containing solid organic resins and metal-organic framework. The breakthrough is needed in the materials on dry sorbents to decrease capture cost.
Jo, Ju-Mi;Lee, Seung-Yeop;Kim, Yu-Seok;Park, Jong-Yun
Proceedings of the Korean Vacuum Society Conference
/
2011.08a
/
pp.386-386
/
2011
탄소나노튜브는 큰 길이 대 직경 비와 뛰어난 전기적 특성으로 인해 차세대 전계 방출 소자로 주목 받고 있다. 실질적인 전계방출 디스플레이로의 응용을 위한 대면적 제작과 유리 기판 사용을 위해 이용되었던 페이스트(paste)법은 높은 전기장 하에서 장시간 전계방출시 탄소나노튜브 전계방출원과 페이스트(paste)간의 낮은 접착력 때문에 발생하는 탄소나노튜브의 탈루현상(omission)과 유기물질(organic paste)에서 발생하는 탈기체(out-gassing) 문제점이 있었다. 최근 이런 문제점을 개선하기 위해 유기물질(organic paste)를 대체하여 금속바인더(metal binder) 물질을 사용한 결과들이 보고되고 있다. 본 연구에서는 유리기판 위에 제작된 탄소나노튜브 전계방출원의 수명 향상을 위하여 금속바인더와 후속 열처리법의 변화에 따른 전계방출 안정성을 분석하였다. 금속바인더는 접합층/ 접착층(soldering layer/ adhesive layer)으로 구성되어 있으며, 일반적인 소다석회유리(soda-lime glass)에 스퍼터(DC magnetron sputtering system)를 이용하여 증착하였다. 접착층은 유리기판과 접합층의 접착력 향상을 위해 사용되며, 접합층은 기판과 탄소나노튜브 전계방출원을 접합하는 역할과 전계방출 측정시 전극이 되기 때문에 우수한 전기 전도성과 내산화성을 필요로 한다. 본 실험에서는 일반적으로 유리기판과 접착력이 좋다고 알려진 Cr, Ti, Ni, Mo을 접착층으로 사용하였으며, 접합성과 전기전도성, 내산화성이 뛰어난 귀금속 계열의 금속을 접합층으로 사용하였다. 탄소나노튜브를 1,2-디클로로에탄(1,2-dichloroethane, DCE)에 분산시킨 용액을 스프레이방법을 이용하여 증착시켰으며, 후속 열처리 방법을 통하여 접합층과 결합시켰다. 금속바인더와 후속 열처리법의 변화에 따른 접착력과 표면형상(morphology)의 변화를 주사전자현미경(scanning electron microscopy)를 이용하여 분석하였으며, 다이오드 타입에 디씨 바이어스(DC bias)를 사용하여 전계방출특성을 측정하였다[1,2].
Two new copper(I) complexes with organic ligands, $[Cu^I(hfac)]_2(DVTMSO)$ and $[Cu^I(hfac)]_2(HD)$ (hfac=hexafluoroacetylacetonate, DVTMSO=1,2-divinylte-tramethyl-disiloxane, HD=1,5-hexadiene) were synthesized and used for copper metal-organic chemical vapor deposition. In these compounds, two Cu(hfac) fragments are bonded by one neutral ligand forming unusual structure with respect to other Cu(I) complexes. The compounds exhibited relatively high volatility and stability when compared to other copper(I) precursors. By using the reported compounds as precursors, a continuous Cu layer was not formed but the Cu islands were only observed. And the shape and size of Cu islands are significantly changed as a function of the substrate temperature.
Yong Il Park;Ji Hun Jung;Sung Hyun Woo;Jung Heon Lee;Hyeong-Jun Kim
Journal of the Korean Crystal Growth and Crystal Technology
/
v.34
no.3
/
pp.103-107
/
2024
In this study, nickel, a pure metal material, was proposed as a saggar for synthesizing NCM [Li(NixCoyMnz)O2] cathode active material. Nickel is known as a metal that is resistant to oxidation and has a high melting point. Nickel is one of the main components of NCM cathode material and was expected to be free from problems with contamination from saggar during cathode material synthesis. We sought to confirm the possibility of nickel as a saggar for synthesizing NCM cathode active materials. When a Ni metal crucible and Ni0.8Co0.1Mn0.1(OH)2 (NCM 811) precursor material were reacted at 900℃ for a long time, the change in the reaction layer on the surface of the crucible over time was analyzed. The nickel crucible reaction layer formed during heat treatment at 900℃ was nickel oxide, and is thought to have been created by simultaneous oxygen diffusion from the cathode precursor oxide and reaction with oxygen in the atmosphere. The change in thickness of the oxide layer appears to slow down after 480 hours, which suggests that the rate of oxygen diffusion from the precursor is reduced. It remained combined without falling out of the crucible until 480 hours. However, it was confirmed that the oxide layer falls off after 720 hours, so it is thought that it can be used as saggar for NCM synthesis only for a certain period of time.
Purpose: The purpose of this study was to evaluate the effect of abutment material on screw-loosening before and after cyclic loading. Among the different materials of abutments, zirconia and metal abutment were used. Material and methods: Two types of implant systems: external butt joint(US II, Osstem Implant, Korea) and internal conical joint(GS II, Osstem Implant, Korea) were used. In each type, specimens were divided into two different kinds of abutments: zirconia and metal(n=5). The implant was rigidly held in a special holding to device ensure fixation. Abutment was connected to 30 Ncm with digital torque gauge, and was retightened in 30 Ncm after 10 minutes. The initial removal torque values were measured. The same specimens were tightened in 30 Ncm again and held in the cycling loading simulator(Instron, USA) according to ISO/FPIS 1480. Cycling loading tests were performed at loads 10 to 250 N, for 1 million cycles, at 14 Hz,(by subjecting sinusoidal wave from 10 to 250 N at a frequency of 14 Hz for 1 million cycles,) and then postload removal torque values were evaluated. Results: 1. In all samples, the removal values of abutment screw were lower than tightening torque values(30 Ncm), but the phenomenon of the screw loosening was not observed. 2. In both of the implant systems, initial and postload removal torque of zirconia abutment were significantly higher than those of metal abutment(P<.05). 3. In both of the implant systems, the difference in removal torque ratio between zirconia abutment and metal abutment was not significant(P>.05). 4. In metal abutments, the removal torque ratio of GS II system(internal conical joint system) was lower than that of US II system(external butt joint system)(P<.05). 5. In zirconia abutments, the difference in removal torque ratio between the two implant systems was not significant(P>.05). Conclusion: Zirconia abutment had a good screw joint stability in the condition of one million cycling loading.
We report theoretical and experimental investigation of a polarizer made of single mode side-polished fiber covered with a metal film. The influence of the metal film thickness and the refractive index of overlay on the device performance has been analyzed in terms of the normal mode theory. Based on the theoretical prediction, a polarizer with 40 ㏈ of polarization extinction ratio and 0.5 ㏈ insertion loss at optical communication wavelength has been realized.
Proceedings of the Korean Society of Applied Pharmacology
/
1992.05a
/
pp.28-28
/
1992
브라디키닌은 체내에서 강력한 혈관 확장 작용을 일으키는 autacoid(local hormone)로서 혈압의 항상성 유지, 모세혈관 투과성 증진, 염증 및 통증 반응 등에 관여하고 여러 장관 평활근을 수축시킨다. 또한 septic 혹은 endotoxic shock의 여러 원인 물질로도 생각되어진다. 최근 rhinovirus로 인한 감기의 제증상 원인 물질로도 브라디키닌이 주목을 받고있다. 이와같이 브라디키닌온 다양한 질병에 있어 중요한 원인 물질로 여겨지므로 브라디키닌 길항제들은 한두 질병의 치료제로 개발될 가능성이 높음이 강력히 제시되고 있는 실정이다. 이의 개발을 위해서 브라디키닌 수용체에 대한 연구는 필수적이라고 할 수 있다. 본 연구는 두 부분으로 나누어 진행중인데 첫째, 이제까지 보고된 브라디키닌 길항 물질들은 대부분이 브라디키닌의 특정 아미노산 잔기를 치환시킨 펩타이드 유도체로서 이들을 경구 투여시 peptidase어 의하여 쉽게 분해되고 또한 부분적인 효능제 활성을 갖는 불리한 점을 감안하여, 비펩타이드성 브라디키닌 길항제를 개발할 목적으로 한방 및 민간에서 자주 사용되어온 생약중에 브라디키닌 작용에 선택적 길항효과가 있는 물질을 검색한 바 활성을 보인 황금으로부터 작용 성분을 추적중에 있다. 둘째, 브라디키닌 수용체를 순수하게 분리 정제하기 위한 첫 단계로서 이 수용체의 결합시험(binding assay) 방법을 확립하고 더불어 여러 조직내(흰쥐의 여러 기관, 토끼 및 사람의 신장)의 브라디키닌 수용체의 분포를 파악하는 일이다. 횐쥐 조직의 실험 결과로부터 신장에 브라디키닌 수용체가 많이 분포함을 확인되었고 향후 토끼 신장으로부터 동수용체를 분리하고자 한다. 또한 토끼 신장의 근위세뇨관일차배양세포을 이용하여 브라디키닌의 신장에서의 작용기전도 살펴보고 있다.+}$, $Na^{+}$, NH$_{4}$$^{+}$ 및 H$^{+}$) 수용액 메디움에서의 Cd(II), Mg(II) 및 Zn(II)의 Dowex 1-X8, Cl$^{-}$ 수지에 대한 흡착은 역시 어떤 메디움에서도 Cd(II) 흡착이 제일 크며, 다음이 Zn(II) 이고 착이온을 형성않는 Mg(II)이 제일 작았다. 한편 메디움 종류별 D값의 크기순위는 H$^{+}$>K$^{+}$> $Na^{+}$>NH$_{4}$$^{+}$이였다. 메디움의 종류에 따라 D값의 차이가 나는 것은 금속이온의 착이온 형성과 금속이온의 용액내에서의 이온종의 상태와 관련이 있다고 생각된다. 마. MCl(M:K$^{+}$, $Na^{+}$, NH$_{4}$$^{+}$ 및 H$^{+}$)과 MNO$_{3}$ 용리액에 의한 Cd(II), Mg(II) 및 Zn(II)의 용리는 예상한 바와 같이 MCl에서 작은 Dv 값을 갖는데, 이것은 CdCl$_{4}$$^{2-}$ 착이온을 형성하거나 ZnCl$_{4}$$^{2-}$ , ZnCl$_{3}$$^{-}$같은 이온과 MgCl$^{+}$, MgCl$_{2}$같은 이온종을 형성하기 때문인것 같다. 한편 어떠한 용리액에서던지 NH$_{4}$$^{+}$의 경우
Jack C. Kim;Young-Sim Koh;Ung-Chan Yoon;Min-Sook Kim
Journal of the Korean Chemical Society
/
v.37
no.2
/
pp.228-236
/
1993
The effect of ferric ion on the reaction of CH_3$MgI with benzylbromide was investigated by determining the product ratio between cross-coupling product, ethylbenzene (A) and homocoupling product, bibenzyl (B) in the presence of ferric ion. When CH_3$MgI prepared with pure magnesium was used, the ratio of A to B was 22 to 78 and with reagent grade magnesium, the ratio became 33 to 67 indicating that metallic impurities in magnesium affect the reaction mechanism to lead less homocoupling product, B. The ratio changes became significant when ferric chloride was added in the reaction mixture in catalytic amounts and the ratio of A to B reached to 80 to 20 at maximum. The reaction in the presence of ferric ion seems to follow mainly an ionic mechanism which involves iron-benzyl bromide ${\pi}$-complex formation. The complex formation is expected to be able to enhance ionic attack of CH_3$MgI on benzyl carbon to give more A.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.