• Transactions of the Korean hydrogen and new energy society
• /
• v.24 no.4
• /
• pp.334-339
• /
• 2013

In this study, as a candidate of the carbon dioxide ($CO_2$) absorbents, the mixture solution of polyethylene glycol dimethyl ether (PEGDME) and tetrahydrofuran (THF) were investigated. $CO_2$ absorption rate was measured by using high pressure $CO_2$ screening equipment in the range of 1 - 10wt% THF. Absorption capacity of the mixture solution was also estimated. Based on the results, we found that mixture solution containing THF had higher absorption rate and $CO_2$ loading capacity compared to PEGDME at $25^{\circ}C$.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.119-124
• /
• 2001

Dimethyl terephthalate (DMT). 1.4-butanediol (1.4-BD) and poly (tetramethylene ether) glycol (PTMG) in the molecular weight of 2000 (g/mol) were used to synthesize poly(ether-b-ester) thermoplastic elastomers (TPEEs). The final copolymers were annealed to improve thermal stability at elevated temperatures and mechanical properties. This study showed that as the proportion of soft segment increases melting temperature and degree of crystallinity of TPEEs decrease constantly. In case of mechanical properties like flexural strength and flexural elastic modulus. $35-PTMG^{2000}$ indicates the highest values due to more efficient physical interlock.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.4
• /
• pp.259-269
• /
• 2002

A battery based on the lithium/elemental sulfur redox couple has the advantage of high theoretical specific capacity of 1,675 mAh/g-sulfur. However, Li/S battery has bad cyclic durability at room temperature due to sulfur active material loss resulting from lithium polysulfide dissolution. To improve the cycle life of Li/S battery, PEGDME (Poly(ethylene glycol) dimethyl ether) 500 containing 1M LiTFSI salt which has high viscosity was used as electrolyte to retard the polysulfide dissolution and nano-sized $Mg_{0.6}Ni_{0.4}O$ was added to sulfur cathode as additive to adsorb soluble polysulfide within sulfur cathode. From experimental results, the improvement of the capacity and cycle life of Li/S battery was observed( maximum discharge capacity : 1,185 mAh/g-sulfur, C50/C1 = 85 % ). Through the charge-discharge test, we knew that PEGDME 500 played a role of preventing incomplete charge-discharge $behavior^{1,2)$. And then, in sulfur dissolution analysis and rate capability test, we first confirmed that nano-sized $Mg_{0.6}Ni_{0.4}O$ had polysulfide adsorbing effect and catalytic effect of promoting the Li/S redox reaction. In addition, from BET surface area analysis, we also verified that it played the part of increasing the porosity of sulfur cathode.

• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.809-813
• /
• 1999

D phase emulsification has been developed and elucidated the emulsification mechanism by using phase diagrams. The process of D phase emulsification begins with the formation of isotropic surfactant solution, follows by formation of oil-in-surfactant (O/D) gel emulsion by dispersion of octamethylcyclotetra siloxane(OMCS) in the surfactant solution. Polyols were essential components for this experiments. To understand the function of polyols, the solution behaviors of nonionic surfactant/oil/water/polyol systems were investigated by the ternany phase diagrams of polyoxyethylene oleyl ether/OMCS/propylene glycol(PG) aqueous solutions. The solubility of oil in the isotropic surfactant phase was increased with the addition of PG. D phase emulsion was formed in the range of 70~90% of OMCS and 2.0~3.0 dyne/cm of interfacial tension and the structure was homogenious spherical and O/W type and its diameter was about $10{\mu}m$.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.602-612
• /
• 2014

Polyurethanes containing poly(dimethyl siloxane) (PDMS) unit, PU-Si, were synthesized and their thermal and shape memory properties were investigated. Various amounts of PDMS units were incorporated via a solution polymerization method using mixed diols of poly(tetramethylene ether glycol) (PTMEG) and PDMS-diol as the soft segment (SS) and methylene diphenyl diisocyanate and 1,4-butanediol as the hard segment (HS). Two series of PU-Si samples with an HS content of 23% or 32% were prepared and analyzed. For PU-Si with an HS content of 23%, both the cold crystallization temperature ($T_{cc}$) and melt crystallization temperature of the SS domain moved higher temperature with increasing PDMS content, while the melting temperature ($T_m$) of the SS domain remained unaffected. The increase in HS content from 23% to 32% resulted in the increased $T_m$ and disappearance of $T_{cc}$. The shape recovery of PU-Si flim with an HS content of 32% increased while its shape retention decreased as PDMS content increased.

• Elastomers and Composites
• /
• v.45 no.1
• /
• pp.40-43
• /
• 2010

In this study, polyimide(PI) nanofibers mats were prepared by electrospinning and three different fiber morphologies of random, uniaxial, and biaxial orientation were prepared by controlling the speed of drum-shaped collector and other parameters. The SEM studies reveal that the aforesaid morphologies were obtained on the nano-fibrous mats prepared. The ionic conductivity was measured using an in-plane type conductivity tester for the PI mats soaked in the mixture of 1M lithium trifluoro-methane-sulfonate and tetra-ethylene glycol dimethyl ether. The ionic conductivity was surprisingly higher for the biaxial PI mats. For the uniaxially-oriented mats, the ionic conductivity was found to be higher in the parallel direction compared to the perpendicular direction of the fiber orientation. A curious cyclic fluctuation was found in the ionic conductivity with time. The observed behavior was explained by considering the distance between fibers and transport speed of ions used in this study.

• Journal of the Korean Applied Science and Technology
• /
• v.36 no.2
• /
• pp.524-530
• /
• 2019

In this study, polyether polyol polypropylene glycol and isophorone diisocyanate (IPDI) were synthesized based on polyrupopylene mono methyl eher (PM) for the synthesis of water - soluble polyurethane for coating on leather skin layer. After synthesis of prepolymer, PM was added at $40^{\circ}C$ to 1M, 2M, 3M, and 4M to inhibit the viscosity rise, and neutralization reaction and chain extension reaction were carried out to prepare polyurethane samples. According to the measurement results of the tensile strength, elongation and adhesive strength of the prepared sample, the tensile strength was 2.109 kgf / mm2 for PM 1M, 1.721kgf / mm2 for 4M, elongation was 496% for PM 1M, 522% for 4M, adhesion was 1.114 kgf / cm for PM 1M and 0.99 kgf / cm for 4M.

• Clean Technology
• /
• v.13 no.2
• /
• pp.143-150
• /
• 2007

The objective of this study is to develop hydrocarbon-based cleaning agents by blending paraffins, glycol ethers and siloxanes in oder to effectively clean contaminants such as flux, solder and grease. And the effect of cleaning ability by wetting index, aniline points and solubility parameter of the formulated hydrocarbon-based cleaning agents were studied in this work. The formulated hydrocarbon-based cleaning agents were prepared on the base of physical properties of their individual components. Wetting indexes and aniline points of their were measured through experiments and solubility parameters of their were calculated based on the Hansen's equation. In this study, evaluation of cleaning ability by cleaning agents were carried out using contaminants such as flux, solder, and grease. The experimental results showed that the cleaning ability of the formulated cleaning agents was excellent in cleaning contaminants such as flux, solder and grease and that the influencing parameters on their cleaning efficiency were found to be different according to contaminant types. MC($20.3MPa^{1/2}$), DF-1 ($24.2MPa^{1/2}$) and DF-2($21.5MPa^{1/2}$) with similar solubility parameter as flux ($21.3MPa^{1/2}$) showed 100% cleaning efficiency within 3 minutes in flux cleaning. And CFC-113, MC and 1,1,1-TCE with low aniline point less than $-20^{\circ}C$ showed excellent cleaning efficiency in solder cleaning. DG-1($16.2\;MPa^{1/2}$) and DG-2($15.5\;MPa^{1/2}$) with similar solubility parameter as grease($15.0{\sim}17.0\;MPa^{1/2}$) showed relatively low cleaning efficiency of grease, but CFC-113 and MC with high wetting index and low aniline point showed good cleaning efficiency in grease cleaning. As a result of this study, the hydrocarbon-based cleaning agents alternative to regulated cleaning agents such as CFC-113, 1,1,1-TCE and MC were able to be developed through properly blending paraffins, glycol ethers and siloxanes for cleaning flux, solder and grease. And it can be shown that various influencing parameters of cleaning efficiency such as wetting index, aniline point, solubility parameter and etc. of the non-aqueous cleaning agent should be reviewed for prediction of their cleaning ability and can be applied to formulation of cleaning agents.

• Clean Technology
• /
• v.23 no.3
• /
• pp.237-247
• /
• 2017

In the dimethyl ether (DME) synthesis and separation process, over 8% by mole of $CO_2$ is fed to the DME synthesis reactor which lowers DME productivity. Therefore, this work focused on the removal of $CO_2$ using three kinds of processes with physical absorbents by comparing the utility consumption through computer simulation of each process. Among the processes selected for comparison are Rectisol$^{(R)}$ process using methanol, Purisol$^{(R)}$ process using n-methyl pyrrolidone (NMP), and SelexolTM process using dimethyl ethers of polyethylene glycol (DEPG) as a solvent. As a result of this study, it was concluded that Purisol$^{(R)}$ process consumes the least energy followed by SelexolTM process. Therefore, it is considered that Purisol$^{(R)}$ process is the most suitable method to absorb $CO_2$ contained in the feed of DME synthesis reactor.

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.489-496
• /
• 2006

Graft copolymerized polycarboxylate(PC)-type superplasticizers which have carboxylic acid with $\pi$ bond among the molecular structure and polyethyleneglycol methyl ether methacrylate(PMEM) were synthesized by free radical reaction. To investigate their chemical structures and molecular weights, PCs were analyzed by FT-IR(fourier transform spectrometer), C-NMR(nuclear magnetic resonance spectrometer) and GPC(gel permeation chromatograpy). When types of carboxylic acids(methacrylic acid, acrylic acid, maleic anhydride, and itaconic acid) and molar ratios of carboxylic acid/PMEM) were varied, adsorptive and fluid characteristics in cement paste were discussed. As the molar ratio of carboxylic acid/PMEM) was higher, amount adsorbed on the cement particles and the fluidity of cement paste by mini-slump spread testing method were increased. When main chain of PC was methacrylic acid, a larger amount was adsorbed on the cement particles. PCs with acrylic acid as main chain showed higher dispersing power. However, it was confirmed that PCs with dicarboxylic acids(maleic anhydride, itaconic acid) didn't have good adsorption and dispersibility.