• 한국전자통신학회논문지
• /
• 제17권6호
• /
• pp.1069-1074
• /
• 2022

본 연구에서는 Nb₂O₅/SiO₂ 이중 버퍼층위에 ITO박막을 증착하여, SiO₂버퍼층 두께 변화 (40~50 nm)에 따른 전기적 및 광학적 특성을 조사하였다. Nb₂O₅/SiO₂ 이중 버퍼층을 도입한 ITO박막의 표면 거칠기는 0.815에서 1.181 nm 범위의 작은 값을 가지는 매끄러운 형상을 보였고, 면저항은 99.3~134.0 Ω/sq. 범위로 정전용량식 터치스크린 패널에 적용하는데 문제가 없는 것으로 나타났다. 특히 Nb₂O₅ (10 nm) / SiO₂ (40 nm) 이중 버퍼층을 삽입한 ITO박막의 단파장(400~500 nm) 영역에서의 평균 투과도와 색도(b^*)는 83.58 % 와 0.05로 이중버퍼층이 삽입되지 않은 ITO박막의 74.46 % 와 4.28에 비해 상당히 향상된 결과를 나타내었다. 이를 통해 Nb₂O₅/SiO₂ 이중 버퍼층을 도입한 ITO박막에서 인덱스 매칭 효과로 인해 단파장 영역의 투과도 및 색도와 같은 광학적 특성이 현저히 향상되었음을 확인할 수 있었다.

• 한국멀티미디어학회논문지
• /
• 제13권2호
• /
• pp.332-340
• /
• 2010

본 논문은 우리나라의 대표적인 "문화 콘텐츠"인 전통목조건축물을 컴퓨터 및 멀티미디어 기술을 사용하여 보존, 복원하기 위한 방법론을 제시하고, 방법론에 따라 구현을 하였다. 디지털 콘텐츠로 구현하기 위하여 전통목조건축물의 디지털화 의미와 고려해야 할 요소를 정의하고 제작단계와 제작방법을 제안하였다. 또한, 제안한 방법을 사용하여 경복궁 근정전 및 창덕궁 인정전의 공포부분을 디지털로 제작함에 있어 목조건축의 건축 부재, 구조 및 단청 등을 고려하였다. 두 건물의 공포부분의 부재 수치 관계를 활용하여 하나의 전통목조건축물을 디지털화 하면 다른 전통목조건축물을 디지털화 할 수 있는 방법을 제시하였다. 본 논문의 또 다른 장점은 다른 문화유산 연구가 외부 구현에 중점을 두고 있는데 비하여 내부 구조의 관계성을 밝혀 보존, 복원에 활용할 수 있다는 것이다.

• 보존과학회지
• /
• 제29권4호
• /
• pp.407-420
• /
• 2013

경복궁 석조조형물은 주로 화강암(884점, 96.7%)과 대리암(25점, 2.7%)으로 구성되었으며, 다양한 산지의 석재가 혼용되어 조성되었다. 이 석조조형물에서 나타나는 주요 손상은 균열(24%), 탈락(21%), 박리박락(36%), 입상분해(9%) 및 흑색변색(20%)으로써, 균열과 탈락은 높은 물리적 손상도에, 흑색변색은 높은 변색 손상도에 주로 기여하는 손상유형이다. 구역별로는 경회루(3등급 55%), 근정전(3등급 29%) 및 품계석(3등급 11%) 구역의 석조조형물에서 상대적으로 손상도가 높아 이들을 우선관리대상으로 설정하여 집중적으로 관리하고 정기모니터링 하는 것이 필요하다. 특히 품계석은 대리암으로 구성되어 외부환경에 노출될 시 풍화민감도가 크므로 강우와 일사를 제어할 수 있는 보호시설이 요구된다.

• 건축역사연구
• /
• 제16권1호
• /
• pp.83-99
• /
• 2007

This study examines the joint and splice of wooden structure at Geunjeongjeon Hall of Gyengbok Palace, which was constructed in the late Joseon Dynasty. The scope of the study is on the part of columns, the bracket sets, and the frame structure. This research also deals with the relationship between vortical load and horizontal load. Firstly, the examination of the joint and splice methods between the pillar and penetrating ties is on the joint and splice methods of the outer and corner. Through the investigation, it is verified that the joint methods between pillar and penetrating tie on the outer and corner pillars is the method of Sagal joints(cross joints, 사개맞춤). Joints used between pillar and penetrating tie are dovetailed tenon joints, between columns and Anchogong(안초공), between columns and Choikgong(초익공) are tenon joint(장부맞춤). Secondly, the examination of the joint and splice methods of the bracket set is on that of Salmi and Cheomcha(첨차), and Salmi and Janghyeo(장혀). Joints used between Salmi and Cheomcha, Salmi and Janghyeo are halved joint, and between each Janghyeo are stepped dovetailed splice. It is Cheomcha that is used the Jujang-Cheomcha(주장첨차) on center line. Therefore it is connected with each bracket set, which gets to is the strong system, easy and convenient on the construction of that. Thirdly, the frame structure of wooden architecture in royal palace is consist of purlins and beams, Janghyeo(장혀, timber under purlin), tall columns, king posts, etc. Through the investigation, it is verified that the joint and splice methods between purlins and beams are used with the methods of Sungeoteok joint(숭어턱맞춤). It is verified that the joint and splice methods between beams and high columns are used with methods of mortise and tenon joint(장부맞춤), is highly related with tensile force. To reduce the separation of parts, sangi(산지) and tishoi(띠쇠) are used as a counterproposal, which were generally used for architecture in royal Palaces in the late Joseon Dynasty and continued to be used until these days common wooden architecture.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.401-407
• /
• 2004

This study is on the constant-current stress corrosion test related to the load stress in welded zone and non-welded zone of high tensile strength steel for natural gas transmission. The surface corrosion pattern of the welded zone of API 5L-X65 specimens for natural gas transmission showed global corrosion and narrow pitting, and the pitting was increased by increasing the load stress. Initially, the average relative electrode potential and the average relative current of the high tensile strength steel for natural gas transmission specimens was decreased suddenly, and the average relative electrode potential was higher and the average relative current was lower in welded zone than base metal. and the average relative electrode potential was decreased by increasing the load stress, and the average relative current was somewhat increased by increasing the load stress. The corrosion rate was less in welded zone than base metal, and the corrosion rate was decreased by increasing the load stress.

• 동력기계공학회지
• /
• 제8권3호
• /
• pp.44-51
• /
• 2004

Effect of corrosion characteristics in relation to loaded stress in the welded zone of A5083-H116 aluminum alloy, in the seawater was studied. The corrosion experiment was performed for 120 hours on the specimens in the natural seawater tank with four steps of the loaded stress. The corrosion crack, corrosion rate, electrode potential, current, and corrosion pattern, etc. were examined for the specimens with the elapse of the immersion time. The main result derived from this study is the crack growth length is increased with the increasing loaded stress. The electrode potential and the corrosion current are decreased rapidly in the early stage of the corrosion, and then decreased gradually and stabilized eventually with the elapse of the immersion time. The test condition of the longer crack growth tends to show the higher corrosion rate. Corrosion pattern of the welded zone indicates that the depth and width of the pitting become increasing with the increasing loaded stress.

• 전기학회논문지
• /
• 제62권7호
• /
• pp.913-917
• /
• 2013

During the restoration process of primary restorative transmission system, some over voltages may happen due to nonlinear interaction between unloaded transformers and transmission systems. These over voltages caused by harmonic resonance can be suppressed by inserting damping loads before energizing transformers. But it is very difficult to predict the occurrence possibility of harmonic resonance and complex simulation must be repeated to estimate the sufficient damping loads. This paper presents a damping loads prediction system to prevent harmonic resonance. Detailed analysis of the relationship between harmonic resonance and the amount of damping loads is discussed. The prediction system is developed using a curve fitting and a neural network based on this relationship. A curve fitting used a Gaussian function based on non-linear least square method and multi-layer back-propagation neural network is applied. The system is applied to primary restorative transmission lines in korean power system and the result showed satisfactory performance.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.532-537
• /
• 2000

The purpose of this study is to determine the performance of a commercial air cleaner in removing tobacco smoke indoors. Following injection of tobacco smoke in a room, decay rates for particle concentrations were obtained far mass concentration at each point. The size distribution of the tobacco smoke particles was approximately $1.266{\mu}m$ in mass median diameter with a geometric standard deviation of 1.313. The air cleaner consisted of an electrostatic filtration unit and a fan operated at a flow rate of 5.98 CMM. The collection efficiency for $>1\;{\mu}m$ was more than 99%. Without air cleaner operation, tobacco smoke concentration ratio in room decreased to 30% of initial values within 30 minutes and with air cleaner operation, decreased to 90% of initial values in the test chamber, volume $51.27\;m^3$. Without air cleaner operation, tobacco smoke concentration ratio in room decreased to 10% of initial values within 30 minutes and with air cleaner operation, decreased to 30-70% of initial values in the test chamber, volume $149.2\;m^3$.

• 한국해양공학회지
• /
• 제18권5호
• /
• pp.50-56
• /
• 2004

This study is on the constant-current stress corrosion test, related to the load stress, in both the welded and non-welded zones of high tensile strength steel that is used for natural gas transmission. The surface corrosion pattern of the welded zone of API 5L-X65 specimens for natural gas transmission showed general corrosion and narrow pitting, and the pitting was increased with load stress. Initially, the average relative electrode potential and the average relative current of the high tensile strength steel, used for natural gas transmission specimens, were decreased rapidly, and the average relative electrode potential was higher and the average relative current was lower in welded zone, compared to base metal. The average relative electrode potential was decreased with load stress, and the average relative current was somewhat increased by increasing the load stress. The corrosion rate was less in welded zone, compared to base metal, and the corrosion rate was decreased by increasing the load stress.

• 대한기계학회논문집
• /
• 제19권10호
• /
• pp.2678-2689
• /
• 1995

In this study, a new hot-wire anemometer which has greater sensitivity than that of a constant temperature anemometer (CTA) was proposed. In contrast to CTA, the wire working resistance of the new anemometer increases with flow velocity, that is, the operating mode of the wire becomes variable temperature. The variable temperature anemometer(VTA) was made by substituting a voltage controlled variable resistor such as photoconductive cell or transistor for one of the resistors in the bridge. By positively feeding back the bridge top signal to the input side of these electronic components, the wire overheat ratio could be increased with velocity automatically. Static response analyses of the VTA, constant voltage anemometer (CVA) and CTA were made in detail and calibration experiments were performed to validate the proposed operating principle. The wire operating resistance of the CVA decreases with velocity and this leads to lower sensitivity than that of a CTA. But the sensitivity of the newly proposed VTA is superior to that of a CTA, since the wire overheat ratio increases with velocity. Consequently, it is found that the major factor that is responsible for large sensitivity of a VTA is not the working resistance itself but the change of the wire working resistance with velocity.