• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.4A
• /
• pp.537-548
• /
• 2008

Recently, the prestressed unbonded concrete structures are increasingly being built. The mechanical behavior of prestressed concrete beams with unbonded tendon is different from that of normal bonded PSC beams in that the increment of tendon stress was derived by whole member behavior. The purpose of the present paper is therefore to evaluate the flexural behavior and to propose the equation of ultimate tendon stress by performing static flexural test according to span/depth, concrete compression strength, reinforcement ratio and the effect of existing bonded tendon. From experimental results, for cracking, yielding and ultimate load, the effect of reinforcement ratio was more effective than concrete compression strength, and the beams having high strength concrete had a good performance than having low concrete, but there was no difference between high strength and low strength. And as L/dp was larger, test beams had a long region of ductility. This means that unbonded tendon has a large contribution after reinforcement yielding. Especially, the equation of ACI-318 was not match with test results and had no correlations. After analysis of test results, the equation of ultimate unbonded tendon stress without slip was proposed, and the proposed equation was well matched with test results. So the proposed equation in this paper will be a effective basis for the evaluation of unbonded tendons without slip, analysis and design.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.126-126
• /
• 2023

최근 대한민국에서는 기후변화로 전국 각지에서 돌발성 호우와 태풍의 강도 및 발생빈도가 높아지고 있다. 이에 따라 주요 국가시설이 위치한 해안 도시의 2차원 3차원 모형을 통해 극한 조건하 침수 분석을 수행하였다. 먼저 해양수산부 "2019년 전국 심해설계파 보고서"를 기반으로 극치분포 중 Weibull 분포를 이용하여 극한 조건, 1,000년부터 1,000,000년 빈도의 재현기간의 파도 높이와 풍속을 계산하였다. 계산 결과를 SWAN(Simulating WAves Nearshore)의 입력값으로 해상에서 100m 간격의 파고 높이를 계산하였다. 이때 100m 간격으로는 방파제 지형을 정확히 해석하지 못하였기에, 상세파고 계산을 위한 Nesting 기법을 이용하여 20m 간격의 파고 결과를 도출하였고, 해안 도시 인근 해상에서 10.916m의 파고를 예측하였다. 또한, 예측된 파고를 이용해 EurOtop(2018) 매뉴얼의 경험식을 기반으로 연구 유역으로 유입되는 월류량 계산에 사용하였다. 결과로 16방위 중 SSE 방향, 1,000,000년 빈도 재현기간 조건에서 0.0306cms/m의 월파량을 예측했다. 예측된 자료를 바탕으로 2차원 침수해석은 FLO-2D 모형, 3차원 침수해석은 FLOW-3D 모형을 이용하였다. 2차원 침수해석 결과 주요 지점에서 0.18~0.33m의 침수가 예상되었고 3차원 침수해석 결과 동일한 지점에서 0.240~0.333m의 침수가 예상되었다. 모의 결과 2차원과 3차원 모형 간 침수 예측 결과가 0.3cm에서 6.1cm의 차이를 나타내어 모형 구축이 합리적으로 이뤄졌다고 판단하였으며 연구 유역에서는 침수가 예상된다는 결과를 도출하였다. 본 연구를 통해 기후변화에 따른 해안에 위치한 주요 도시지역과 국가 주요 시설물에 대한 침수해석을 실시하였고 분석결과를 생명과 재산을 보호하기 위한 대피계획 등 재난예방대책 수립에 활용할 수 있음으로 예상된다.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.8
• /
• pp.89-97
• /
• 2008

A series of field tests were performed to investigate the behavior of jacket anchor and to evaluate the ultimate bond stress of jacket anchor. From twelve sets of field tests on the jacket anchor and general type ground anchor, it was observed that the pullout resistance of jacket anchor is significantly larger than that of the ground anchor and that the plastic deformation of jacket anchor is significantly smaller than that of general ground anchor at the same loading cycle. Especially in gravel layers, the jacket anchor provides more than 250% increase in ultimate resistance and more than 600% reduction in plastic deformation, compared with the general ground anchor. Finally, the relationship between the injection pressure and overburden pressure is proposed to determine the optimum injection pressure, based on additional field test results.

• Bioindustry News
• /
• v.21 no.2
• /
• pp.4-11
• /
• 2008

• Journal of the Korean Geotechnical Society
• /
• v.22 no.9
• /
• pp.23-36
• /
• 2006

This study presents the development of a new closed-form analytical solution for the ultimate bearing capacity of an embedded wall in a granular mass. The closed-form analytical solution consists of upper and lower bound solutions (UB and LB). The calculated values from these bound solutions were compared with the author's two-dimensional laboratory wall model loading test and finite element analysis in the plastic region. The comparison showed that ultimate bearing loads from both the model test and finite element analysis are located between UB and LB. In particular, the ultimate bearing load from LB showed good agreement with the ultimate bearing load values from both the model test and finite element analysis. However, the calculated value from the conventional empirical form subjected to plane-strain conditions was shown to be much smaller than the LB.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4A
• /
• pp.315-327
• /
• 2009

In this study, the static test of CFT truss girders for different f/L ratios was conducted to determine how the ultimate strength of the CFT truss girder was affected by different f/L ratios. A total of two CFT truss girders were constructed and tested under bending condition. The length of all specimens is 20,000 mm. The CFT truss girder is a tubular truss composed of chord members made of concrete-filled circular tubes. The main parameter analyzed in the experimental study was the f/L ratio. This factor was experimentally investigated to assess their influence on ultimate strength and stiffness. The test results show that CFT truss girder has good elastic-plastic property and ductility. The presence of the f/L ratios in CFT truss girders alters its ultimate strength because of the global stiffness of the CFT truss girders. The ultimate strength of CFT truss girders increases as the f/L ratio increases. If the f/L ratio of the CFT truss girders increases twofold, the ultimate strengths increase by 80%. The CFT truss girders showed that they retained large deformation capacity, even after reaching the ultimate strength. Results of this investigation demonstrated the potential for efficiently using a CFT truss as a bridge girder.

• Computational Structural Engineering
• /
• v.20 no.3
• /
• pp.18-24
• /
• 2007

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.12 no.1
• /
• pp.1907-1911
• /
• 1970

• Computational Structural Engineering
• /
• v.18 no.3 s.69
• /
• pp.50-55
• /
• 2005

• Journal of Ocean Engineering and Technology
• /
• v.5 no.2
• /
• pp.183-183
• /
• 1991