• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.5
• /
• pp.399-406
• /
• 2016

The large scale wind turbine blades usually experience periodic change of inflow speed due to blade rotation inside the ground shear flow region. Because of the vertical wind shear, the inflow velocity in the boundary layer region is maximum at uppermost position and minimum at lowermost position. These spatial distribution of wind speeds can lead to the periodic oscillation of the 6-component loads at hub and low speed shaft of the wind turbine rotor. In this study we compare the aerodynamic loads between two inflow conditions, i.e, uniform flow (no vertical wind shear effect) and normal wind profile. From the computed results all of the relative errors for oscillating amplitudes increased due to the ground shear flow effect. Especially bending moment and thrust at hub, and bending moments at LSS increased enormously. It turns out that the aerodynamic analysis including the ground shear flow effect must be considered for fatigue analysis.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.1057-1058
• /
• 2008

철도차량용 선형추진시스템에 있어서, 지상레일에 설치되는 선형유도전동기의 2차측의 리액션플레이트의 시공 공차에 의해서 발생되는 1차측과의 공극의 변화는 추진 시스템의 운행 시 승차감과 기기효율을 떨어뜨리는 결과를 초래하기 때문에 선형유도전동기의 균일 공극 운전은 추진 시스템의 효율을 증가시킬 수 있는 중요한 사항이다. 또한 경사구간에서의 선형유도전동기의 공극길이 조절을 통해서 선형유도 전동기의 용량 변경 없이 추력을 증가시키는 것이 가능하다. 따라서 본 논문에서는 선형유도전동기의 공극 길이를 제어할 수 있으며, 공극 길이제어를 통하여 추진 시스템의 성능 변화를 살펴볼 수 있는 축소 모델선형유도전동기 성능시험기의 공극조절 시스템의 동적 모델링 및 특성 해석을 통하여 시스템을 구성하는 파라미터들의 특성 변화 분석 및 시스템 구현 가능성에 대한 연구를 수행하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.32 no.1
• /
• pp.83-93
• /
• 1995

A numerical and experimental investigation on the flow characteristics in the rectangular duct of an MHD propulsion system has been carried out. In numerical analysis, three-dimensional, steady-state, viscous, incompressible electrically conducting fluid flow under the influence of uniformly applied magnetic and electric fields was treated using a finite-difference technique. It was found from the numerical study that when the Lorentz force is weak, the typical parabolic velocity profile under a laminar flow condition changes to an M shaped profile near the electrode region and that the pressure increases linearly from the inlet toward the outlet of the MHD duct under constant electro-magnetic field. In experiment, thrust of the MHD propulsion system can be controlled easily by varying electrode current. The measured pressure gradient along the MHD duct is proportional to the Lorentz force, which is in agreement with the numerical results.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.153-162
• /
• 2002

This paper predicted the engineering constants of spatially reinforced carbon/ carbon composites and analyzed the mechanical behaviour of the kick motor nozzle. Those equivalent engineering constants are used to analyze the mechanical behaviour of the kick motor nozzle. Because the distribution of equivalent engineering constants is varying as change its structure, we made a program to predict engineering constants of spatially reinforced composites. The kick motor nozzle consists of graphite or spatially reinforced carbon/ carbon composites for the nozzle throat, carbon/ phenol for the nozzle entrance and the expansion part, and steel for the outer surface of the expansion part. The 4-D carbon/ carbon composite shows the smallest deformed shape of the nozzle throat, which has a favorable effect on the rocket thrust, and the most uniform deformation of all nozzle throat materials. In addition to analysis, ground firing tests of 4D C/ C nozzle throat and graphite nozzle throat were performed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.19-28
• /
• 2014

Firing test of solid rocket motor with pintle-technology carried out and the measured pressure-time curve was compared with the values predicted by the internal ballistic and performance analysis. Without baffle, the measured combustion chamber pressure was similar with the predicted pressure at the beginning of combustion, but gradual increase in pressure, which was unexpected with the end-burning grain of which burning area is constant, was observed. A baffle was inserted to make uniform flow over the pintle. Unlike the thruster without baffle, the measured combustion chamber pressure was 1.4 times higher than the predicted value. Through the CFD simulation, 10% of total pressure loss of the flow was observed from combustion chamber to nozzle throat when the baffle was inserted. The measured pressure with baffle was predicted well by considering the total pressure loss in the internal ballistic modelling and performance analysis.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.9
• /
• pp.658-664
• /
• 2019

In the development of the liquid rocket engine using the pintle injector, spray characteristics such as spray angle, droplet size, and distribution of the droplets are dominant parameters. Three different kind of multi hole type pintle tip and a continuous type pintle tip were designed. In the case of multi hole pintle tip, SMD result did not have a significant difference depending on the number of holes. In analysis with visualization images, however, the droplets were uniformly distributed as the number of holes increased. Liquid droplets from continuous type pintle tip were finely atomized and dispersed uniformly than those from multi-hole type pintle tip. In addition, the thrust control by adjusting the liquid injection area of the pintle is suitable for the continuous type, which is easier to face-shutoff rather than the multi hole type. The spray angle of each pintle tip according to TMR was measured to derive a specific tendency and corresponding empirical formula.

• Journal of the Society of Naval Architects of Korea
• /
• v.28 no.2
• /
• pp.52-68
• /
• 1991

A new propeller series is developed using the newly developed blade section(KH18 section) which behaves better cavitation characteristics and higher lift-drag ratio at wide range of angle-of-attack. The pitch and camber distributions are disigned in order to have the same radial and chordwise loading distribution with the selected circumferentially averaged wake input. Since the geometries of the series propeller, such as chord length, thickness, skew and rate distribations, are selected by regression of the recent full scale propeller geometric data, the performance prediction of a propeller at preliminary design stage can be mure realistic. Number of blades of the series propellers is 4 and the expanded blade area ratios are 0.3, 0.45, 0.6 and 0.75. Mean pitch ratios are selected as 0.5, 0.65, 0.8, 0.75 and 1.1 for each expanded area ratio. The new propeller series is composed of 20 propellers and is named as KD(KRISO-DAEWOO) propeller series. Propeller open water tests are performed at the experimental towing tank, and the cavitation observation tests and fluctuating pressure measurements are carried out at the cavitation tunnel of KRISO. $B_{P}-\delta$ curves, which can be used to select the optimum propeller diameter at the preliminary design stage, are derived from a regression analysis of the propeller often water test results. The KD-cavitation chart is derived from the cavitation observation test results by choosing the local maximum lift coefficient and the local cavitation number as parameters. The caviy extent of a propeller can be predicted more accurately by using the KD-cavitation chart at a preliminary design stage, since it is derived from the results of the cavitation observation tests in the selected ship's wake, whereas the existing cavitation charts, such as the Burrill's cavitation chart, are derived from the test results in uniform flow.