• CORROSION AND PROTECTION
• /
• v.12 no.1
• /
• pp.12-23
• /
• 2013

원자력 발전소 주요 부품에 사용되는 Alloy 600의 PWSCC 개시와 전파기구를 살펴보고 그 억제 기술을 소개하였다. ○ 균열은 경화된 표면 산화층이 깨질 경우, 입계부식, 공식(pitting), 열처리 또는 물속에 노출되었을 때 일어나는 선택부식(selective corrosion), MnS등 게재물의 용출등에 의해 시작된다. ○ 균열의 전파는 '느린 성장'과 '빠른 성장'으로 구별해 볼 수 있는데 빠른 균열성장은 균열 선단에서의 응력확대 계수(K_I)가 균열이 전파하는 임계값(K_Iscc)을 넘는 경우에 일어난다. ○ Slip Dissolution/Film Rupture Model, Enhanced surface mobility model, Hydrogen assisted creep rupture, Internal oxidation 등의 모델이 제시되어 있으며 Internal oxidation 모델이 여러 실험자료로 잘 뒷 받침되고 있다. ○ PWSCC 억제 방안으로는 부식환경과의 격리 및 보수용접이 대표적이며 부품의 교체를 통한 안전 확보의 방안도 있다. 수소량 조절을 통한 억제 방안도 제시되어 있다. ○ Alloy 600 PWSCC열화 관리 전략프로그램은 결함 발생 가능성이 높은 부위 선정, 우선 순위에 따른 계획적인 검사, 결함이 발견될 경우 완화조치를 취하거나 필요시 교체/보수를 실시하고 그 운영프로그램을 지속적으로 갱신관리하는 방안으로 유지되어야 한다.

• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.161-167
• /
• 2001

It is difficult to obtain accurate fracture toughness values using three point bending test(TPB) proposed by RILEM committees because the shape of load-deflection curve is irregular and final crack propagation occurs after some slow stable cracking. However, fracture toughness is easily obtained from crack initiation load in the disk test. In this paper, the fracture properties of high strength concrete disks with center-crack was investigated. For this purpose, the experimental results were compared with the results by finite element analysis(FEA). And the experimental fracture locus was compared with theoretical fracture locus. Also, the results of fracture properties for the degree of concrete strength are presented. It is concluded from this study that results from FEA with maximum stress theory were compared well with the results from experiment. And the degree of concrete strength was contributed to the crack initiation load and fracture toughness, but was not contributed to the failure angle. Also, The discrepancy of fracture locus between the maximum stress theory and the experiment for concrete is considered to depend upon a large energy requirement for inducing the mixed-mode and sliding mode fractures.

• Journal of the KSME
• /
• v.30 no.2
• /
• pp.107-114
• /
• 1990

(1) Cr-Mo-V 합금강 로우터재료는 사용도중 템퍼 취화된다. 템퍼취화된 소재는 취성제거처리 혹 은 재열처리를 하여 취성을 감소시킬 수 있다. (2) 축의 신뢰도를 파괴역학 원리를 적용하여 계산하였으며 템퍼 취화된 소재는 파손 위험성이 있으나 열처리 된 소재는 취성파괴 및 고 사이클 하중에 의한 피로균열 성장에 대해서 안전성 이 충분하다는 결론을 얻을 수 있다. (3) 샬피 V-노치 충격치 (CVN)와 파괴인성치(K$_{tc}$ )의 관계식을 취성재료에도 적용할 수 있 는가의 여부에 대해서는 많은 조사가 필요하다. (4) 취성소재의 피로균열 개시값$\Delta$ $K_{th}$을 알고 있으면 취송소재로 제조된 구조물의 파괴역학적인 해석을 하는데 도움을 줄 수 있다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.202-202
• /
• 2016

API X-80강재의 수소유기균열(HIC)현상을 비파괴적으로 평가하는 장치를 구축하고 금상학적 평가를 수행하였다. 시편은 열간 압연된 API X-80강재이며 평균입도는 약 $1.76-1.99{\mu}m$ 이었다. 압연재의 금상학적 집합조직은 (110)극점은 ND방향에 평행, (100)극점은 TD방향으로 약 $30^{\circ}$, TD방향으로부터 RD방향으로 약 $45^{\circ}$ 기울어져 있으며, (211)면은 RD방향에 수직인 면으로부터 TD방향으로 약 $35^{\circ}$ 기울어져서 있었다. Pin-on-disk형 마모시험기를 이용한 상온 평균 마찰계수는 0.745였으며 마모손실은 0.0196 mm/min 이었다. 3축 제어 초음파 비파괴 검사 장비는 표면으로부터 약 3mm 깊이의 1 mm 크기의 모의 균열을 탐촉자가 10 mm 접근하면 검출이 가능하였다. HIC시험분위기(NACE-standard TM 0248)에 1일 이상 장입하면 초음파비파괴검사장비로 측정될 수 있는 마이크로미터크기의 균열을 측정할 수 있었다.

• Tunnel and Underground Space
• /
• v.28 no.5
• /
• pp.442-456
• /
• 2018

Scaled model tests were performed to evaluate the reinforcement effect of rock bolts in anisotropic rock mass. For this purpose, two tunnel cases were experimented which had different tunnel sizes, rock strengths, anisotropic angles and coefficients of lateral pressure. The fully grouted rock bolts of the D25 deformed bar were modeled as the basting pins with bead and were systematically installed at the roof and the side wall of the model tunnel. As results of the first case experimentations, the unsupported model showed initial crack at the roof of tunnel, but the supported model with rock bolts showed initial crack at the floor of tunnel where rock bolts were not installed. The crack initiating pressure and the maximum pressure of the supported model with rock bolts were 11% and 7% larger than those of the unsupported model, respectively. Moreover, the effect of the existing discontinuities in anisotropic rock mass on the fracture behavior of tunnel was reduced in the supported model, and so the reinforcement effect of rock bolt turned out to be experimentally verified. As results of the second case experimentations considering different support patterns, the crack initiating pressures of models were larger and the reduction ratios of tunnel area according to applied load were smaller as the length and the quantity of rock bolts were larger. Therefore, it was found that the performance of the rock bolts turned out to be improved as they were larger.

• Journal of the Korean Institute of Gas
• /
• v.2 no.1
• /
• pp.99-106
• /
• 1998

In order to investigate the impact properties of structural materials for LNG tank, instrumented Charpy impact tests were carried out at cryogenic temperatures. $9\%$ Ni steel showed a superior fracture resistance because of less degradation in toughness until 77 K. From the load-deflection curve obtained by an instrumented methods it was found that with the decrease of temperature from 173 K to 77 K, the peak load in the curve increased, but the total absorbed energy decreased. In addition, the energy absorbed during the crack growth was larger than one absorbed in the process of crack initiation. In SUS304L material, the energy absorbed in the process of the crack initiation was relatively large, but the energy absorbed in the process of crack growth was small, the behavior of absorbed energy was well agreed with the observations of the fracture surface which showed a relatively smooth fracture surface. The absorbed Charpy impact energy in the case of A5083 alloy was lower as compared with other steels, and some cracks were observed along the crack propagation direction at the fracture surface of 77 K.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.4
• /
• pp.327-351
• /
• 2009

Laboratory tests are performed in this paper to investigate the brittle failure characteristics of over-stressed rocks taken in deep depth. Also, numerical simulation performed using that the so-called CWFS(Cohesion Weakening Frictional Strengthening) model is known to predict brittle failure phenomenon reasonably well. The most typical rock types of Korean peninsula - granite and gneiss - were used for testing. Results of uniaxial compression tests showed that the crack initiation stress was about 41 % to 42% of the uniaxial compressive strength regardless of rock types, where as, the crack damage stress of granite was about 75%, and that of gneiss was about 97%. Through the damage-controlled test, strength parameters of each rock were obtained as a function of damage degree. After the peak, the crack damage stress and the maximum stress were decreased, The cohesion was decreased and the friction angle was increased with increase of rock damage. Before reaching the peak, the elastic modulus was slightly increased, while decreased after the peak. Poisson's ratio was increased as the damage of rock proceeds. Comparison of uniaxial compression tests and damage-controlled tests shows the crack initiation stress estimated from the damage-controlled test fluctuated within the range of crack initiation stress obtained from the uniaxial compression test; the crack damage stress was less than that estimated from the uniaxial compression test. In order to predict the critical depth that brittle failure occurs, numerical simulations using the CWFS model were performed for an example site. Material parameters obtained from the laboratory tests mentioned above were used for CWFS simulation. Comparison between the critical depth predicted from the numerical simulation using the CWFS model and that predicted by using the damage index proposed by Martin et al.(l999), showed that critical depth cannot be reasonably predicted by the currently used damage index except for circular tunnels. A modified damage index was proposed by the author which takes the shape of tunnels other than circular into account.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.29-32
• /
• 2007

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.103-111
• /
• 1990

This paper presents a methodology for predicting stable crack growth and instability of a cracked body under monotonically increasing load. It is based on a model that incremental crack extensions and load increments after fracture initiation occur by turns in sequence and the criterion that the crack grows by an incremebt .delta.a when the opening displacement at the current crack tip increases by a critical value V$_{c}$. It is shown that the value I$_{c}$ = V$_{c}$/ .delta. a is a material constant characterizing ductile crack growth resistance. Along with the fracture initiation toughness value, the constant is used for the calculation of the loads against crack extensions by adding up each increment. The specimen failure is defined to occur when the necessary load increment for crack extension is zero or when the limit load in the current ligament is reached. The predicted failure loads are in good agreement with the avaliable experimental failure loads for the compact and center-cracked tension specimens of 7075-T651, 2024-T351 aluminum alloys and 304 stainless steel.steel.

• Tunnel and Underground Space
• /
• v.30 no.3
• /
• pp.256-269
• /
• 2020

The objective of this study is to evaluate the stress thresholds in crack development and the corrected fracture toughness of KURT granite under dry and saturated conditions. The stress thresholds were identified by calculation of inelastic volumetric strain from an uniaxial compression test. The corrected fracture toughness was estimated by using the Level II method (Chevron Bend specimen), suggested by ISRM (1988), in which non-linear behaviors of rock was taken into account. Average crack initiation stress(σ_ci) and crack damage stress(σ_cd) under a dry condition were 91.1 MPa and 128.7 MPa. While, average crack initiation stress(σ_ci) and crack damage stress(σ_cd) under a saturated condition were 58.2 MPa and 68.2 MPa. The crack initiation stress and crack damage stress of saturated ones decreased 36% and 47% respectively compared to those of dry specimens. A decrease in crack damage stress is relatively larger than that of crack initiation stress under a saturated condition. This indicates that the unstable crack growth can be more easily generated because of the saturation effect of water compared to the dry condition. The average corrected fracture toughness of KURT granite was 0.811 MPa·m^0.5. While, the fracture toughness of saturated KURT granite(K_CB) was 0.620 MPa·m^0.5. The corrected fracture toughness of rock in saturated condition decreases by 23.5% compared to that in dry condition. It is found that the resistance to crack propagation decreases under the saturated geological condition.