• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.1
• /
• pp.53-63
• /
• 1988

Using COD-R curves, instability of crack growth in ductile material is studied here. Tearing modulus $T_{\delta}$, based on the COA concept is defined and the instability criterion $T_{{\delta}{\app}}$> $T_{{\delta}{\mat}}$ is compared with experiments. Variations of the COD-R curve and the location of rotation center are experimentally investigated as the initial crack ratio varies. Three-point bend specimens of alloy steel SCM4 are used here and two clip-on gauges are installed in order to obtain the COD-R curve. The results show that the tearing modulus $T_{\delta}$ is a good measure to characterize the instability of crack growth. Also it is found that the location of rotation center is almost constant regardless of the initial crack ratio and the amount of the crack growth.

• Proceedings of the KWS Conference
• /
• 1998.10a
• /
• pp.298-300
• /
• 1998

• 한국도로학회:학술대회논문집
• /
• 2006.03a
• /
• pp.17-22
• /
• 2006

• 한국도로학회:학술대회논문집
• /
• 2005.11a
• /
• pp.109-114
• /
• 2005

• International Journal of Highway Engineering
• /
• v.6 no.4 s.22
• /
• pp.1-12
• /
• 2004

This study evaluated the asphalt binder characteristics for the hot-recycled asphalt mixture in which RAP was added in ambient temperature for surface course as well as for base course. RAPs were collected from four sources and their physical properties were evaluated. Mix designs were performed using 10 and 20% RAP contents for surface courses and 10, 20 and 30% for base courses. A virgin asphalt with the penetration grade of 60-80 was used for mixing recycled mixtures. Physical properties of recycled binders, including penetration, absolute viscosity, GPC, BBR and penetration after TFO were measured. From the results, regression analysis of absolute viscosity versus LMS in GPC showed $R^2$ being over 0.95, showing that GPC results estimate the absolute viscosity with relative accuracy. In BBR test, the resistance of recycled mixtures at low service temperature was inferior to the control, because the low temperature PG of recycled binder was one grade higher than that of the control binder.

• Journal of Soil and Groundwater Environment
• /
• v.6 no.1
• /
• pp.53-62
• /
• 2001

Effects of surface defect on thermal stability and stress crack resistance of high density polyethylene geomembranes in environmental conditions were examined by comparing the mechanical properties, chemical resistance and failure times of geomembranes between defective cases under different temperatures. Artificial surface defects were added to the surface of geomembranes by scratch apparatus designed specially. The number of surface defects was increased with the smaller size of scratch induced particles, and the more scratch addition numbers at the shear rate of scratch induced mechanism, 100mm/min. The tensile strength were decreased but the tensile strain was increased with the above conditions. In chemical resistance of defective geomembranes, the tensile strength were decreased but the tensile strain was increased with the longer immersion period and the higher temperature under the same scratch induced conditions. Finally, failure times of defective geomembranes by ESCR test were shifted to the shorter time ranges by increasing temperatures.

• Journal of the Korea Concrete Institute
• /
• v.20 no.3
• /
• pp.325-333
• /
• 2008

This study evaluated the mechanical performance, shrinkage crack and fire resistance of hybrid fiber (blended steel and polypropylene fiber with different diameter and length) reinforced concrete at elevated temperature. The compressive, splitting tensile, flexural, plastic shrinkage test were conducted to the evaluate the mechanical properties and the resistance of shrinkage crack. Also, the surface investigation, reduction rate of mass and residual compressive test were performed to evaluate the physical and mechanical properties after 400$^{\circ}C$, 600$^{\circ}C$, 800$^{\circ}C$ and 1,200$^{\circ}C$ exposure. Test results showed that the hybrid fiber reinforced concrete improved the mechanical performance, shrinkage crack and fire resistance. The reduction of performance with a temperature change were high at the temperature of $600\sim800^{\circ}C$.

• Journal of the Korea Concrete Institute
• /
• v.15 no.3
• /
• pp.454-461
• /
• 2003

This study addressed a procedure to carry out an experimental study on a behavior of simple and continuous concrete beams. For this purpose, sample concrete beams were fabricated and sensors for the measurement of strains and deflections were attached both on the surface of the beams and inside them. Two types of sensors were used to measure strains associated with loading: electric resistance strain sensors and fiber optic sensors. Displacement gauges were also attached on the bottoms of beams to investigate the behavior of beams more rationally. The behavior of the beams was then evaluated throughout the results measured from different sensors while they were subject to steady loading up to failure. From results of this study, it was found that concurrent use of sensors and displacement gauges is helpful in investigating the behavior of concrete beams more effectively. Especially, combined-type strain sensors specifically fabricated in this experiment were found not to be affected by the occurrence of cracks so significantly and to be very effective in monitoring strains of concrete structure. It was also observed that beams show nonlinear force-displacement relationship and reinforcing bars take charge of resisting the external force once cracks occur in concrete beams.

• Nuclear Engineering and Technology
• /
• v.17 no.3
• /
• pp.211-215
• /
• 1985

The effects of temperature and strain rate on the I-SCC behaviors of Zircaloy-4 were investigated by constant load test at 30$0^{\circ}C$ and constant elongation rate test at 300, 350 and 40$0^{\circ}C$ in 3.34mg $I_2$/㎤. The results showed that I-SCC susceptibility increased as the strain rate decreased or the temperature increased. The empirical relation between the stress and the time to failure at 30$0^{\circ}C$ was given by 1/ $t_{f}$∝exp (0.3$\sigma$/$\sigma$$_{UTS}$-31.5) When the I-SCC susceptibility was expressed by the ratio of fracture energy in iodine atmosphere to that in the inert atmosphere, severe I-SCC susceptibility was found near 7.6$\times$10$^{-6}$ sec at 30$0^{\circ}C$ and the maximum point of I-SCC susceptibility tended to shift to the higher strain rate with increasing the temperature. The quasi-cleavage fracture was observed in I-SCC fracture surface. From these results, it was certain that the film repture step was involved as an important process in the I-SCC mechanism of Zircaloy-4.4.

• Polymer(Korea)
• /
• v.32 no.3
• /
• pp.270-275
• /
• 2008

Crack growth characteristics of elastomeric materials are an important factor determining the strength and durability. In this study, the fatigue crack growth characteristic of filled EPDM compounds with different reinforcing fillers, such as silica and carbon black, was investigated using a newly designed tester. Frequency and test temperature had significant effects on the fatigue crack growth. The crack growth rate decreased with increasing frequency and the rate increased with increasing temperature. A power law relationship between the tearing energy and crack growth was observed for filled EPDM compounds. The crack growth rate reduced with increasing filler contents. Silica filled EPDM showed a better fatigue resistance than carbon black filled EPDM. The crack growth rate of silica filled EPDM decreased up to 30 phr and increased again at 50 phr. The formation of microductile type pits was observed on the fatigue-failure surface of unfilled EPDM, and relatively coarse surface with randomly distributed tear lines was observed on the failure surface of silica filled EPDM.