• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 1999.05a
• /
• pp.38-38
• /
• 1999

매설배관은 도로 혹은 철길올 횡단하는 경우와 같이 굴착에 의한 시공이 불가능한 경우에 압업관을 사용하여 시공하며 이러한 압업관은 배관이 토양의 하중으로부터 안 전하게 유지되도록 하는 기능도 한다. 압엽관은 배관과 접촉이 되지 않도록 절연체 를 배관과의 사이에 삽업올 하도록 규정되어 있는데 여러 가지 이유로 배관과 접촉이 되기도 한디 배관과 압업관이 전기적으로 접촉되면 배관을 방식하기 위한 방식전류 를 압입관에 빼앗기게 되고 압업관 내부의 배관은 비방식 상태에 놓이게 되어 부석이 일어날 가능성이 높다. 본 연구는 실제 매설배관 현장에서 배관과 압입관의 접촉여부 에 대하여 조사한 방법 및 결과에 대한 것이다. 본 연구에서는 압업관의 접촉여부를 확인하기 위하여 다음과 같은 방법을 사용하 였다. 첫째. 배관과 압입관의 방식선위를 단순하게 측정하는 것이다. 배관과 압업관 의 전위가 같은가 다른가를 측정하는 방법이다. 둘째, 배관의 방식전류를 on, off하면서 배관과 압입판의 전위거동을 살펴보는 것이다. 셋째, 배관과 압업관을 언위적으로 접촉시켜 흐르는 전류량을 확인함으로써 접촉여부를 확인할 수 있었다. 넷째 배관을 따라 흐르는 방삭전류량을 측정하였다. 이상과 같은 방법을 사용하여 배판과 접촉된 압압관을 확인할 수 있었다. 접촉된 압입관에서 접촉지점을 확인하기 위하여 배관과 압입관 사이에 전류를 인가하고 압입 관의 양단의 배판 사이의 전위 변화를 측정하여 그 전위변화값과 인가한 전류값을 통 하여 계산된 저항올 배관의 길이로 환산하여 대략적인 접촉지점을 확인할 수 있었다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.2
• /
• pp.97-114
• /
• 2011

It is not uncommon that private wells and small streams are used for daily life in the regions where mountain tunnels are located. Then serious social problems such as well water level fall, being attributable to tunnel excavation can occur. In the design stage, firstly we evaluated that the quantity of leakage water into tunnels. And groundwater drawdown area was simulated using numerical modeling such as MODFLOW to reduce adverse effects on life environment around tunnel. In addition we also used hydrological method to evaluate the groundwater change of tunnel area.

• Tunnel and Underground Space
• /
• v.20 no.6
• /
• pp.408-420
• /
• 2010

It is important to forecast the final deformation of a tunnel during construction for evaluating its mechanical stability. In this study, the final deformation of a tunnel is forecasted by fitting tunnel deformations measured while excavating to a displacement function and exterpolating it. The tunnel for the study was built in two stages divided into an upper and a lower part. During the lower part construction of the tunnel, the displacement function forecasts the final incremental displacement well compared to the increment measured after completion of the tunnel. It is because the critical initial displacement occurred on passing the measurement pins can be adequately measured during excavating the lower part, which can not be measured during the upper part excavation of the tunnel.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.4
• /
• pp.1529-1539
• /
• 2013

Recent case studies in Japan have shown that rockbolts are commonly installed at an oblique angle to the excavation direction of the tunnel, instead of at a right angle, due to restriction of the working space. In particular, in the case of expansion in an existing tunnel, the working space can be very small, due to the large protective structures necessary to operate within an existing tunnel. In this case, where both the current use of the existing tunnel, and the reinforcement of the ground around the tunnel are required, the effects of installation angles and patterns of rockbolts are important factors in the design process. Therefore, in this study, a total number of 24 model tests are performed, to investigate the reinforcing effects of system bolting installed obliquely from the excavation direction of the tunnel, by changing the installation angle of bolts, longitudinal distance, and bonded length of bolts. The model test results indicate that the relaxed load ratio decreases, with the increase of both the bonded lengths and the number of the installed bolts, resulting in the decrease of the supported area by one bolt. Two-dimensional numerical analysis, which considered the reinforcement effect of inclined system bolting as the change of engineering properties near the tunnel, demonstrated that the deflection patterns at the tunnel crown in the numerical simulations, show a similar tendency to those measured in the model tests.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.7
• /
• pp.197-206
• /
• 2004

The ground anchor support system may not be occasionally used because of space limitations in urban excavation sites nearby the existing structures. In this case, soil nailing system with relatively short length of nails could be efficiently adopted as an alternative method. The general soil nailing support system, however, may result in excessive deformations particularly in an excavation zone of the existing weak subsoils. Pretensioning the soil nails then could play important roles to reduce deformations mainly in the upper part of the nailed-soil excavation system as well as to improve local stability. In this study, a newly modified soil nailing technology named as the PSN (Pretension Soil Nailing), is developed to reduce both facing displacements and ground surface settlements in top-down excavation process as well as to increase the global stability. Up to now, the analytical procedure and design technique are proposed to evaluate maximum pretension force and stability of the PSN system. Also, proposed are techniques to determine the required thickness of a shotcrete facing and to estimate probability of a failure against the punching shear, Based on the proposed procedure and technique, effects of the radius of a influence circle and dilatancy angle on the thickness of a shotcrete facing, bonded length and safety factors are analyzed. In addition, effects of the reduction of deformations expected by pretension of the soil nails are examined in detail throughout an illustrative example and the $FLAC^{2D}$ program analysis. And a numerical approach is proposed PSN system using the shear strength reduction technique with the $FLAC^{2D}$ program.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.167-178
• /
• 2003

Damage and overbreak of the remaining rock induced by blasting can not be avoided during tunnel construction which may result in either short-term or long-term tunnel instability. Therefore, in this paper, a methodology to take into account the effect of blast-induced damage in tunnel stability assessment is proposed. Dynamic numerical analysis was executed to evaluate damage and overbreak of the remaining rock for the most common blasting pattern in road tunnel. Rock damage was quantified by utilizing the damage variable factor which is adopted proposed in continuum damage mechanics. The damaged rock stiffness and the damaged failure criteria are used to consider the effect of rock damage in tunnel stability analysis. The damaged geological strength index of the damaged rock was newly proposed from the relationship between deformation modulus and geological strength index. Also the Hoek-Brown failure criteria of the damaged rock was obtained using the damaged geological strength index. Analysing the tunnel stability with the consideration of the blast-induced damage of remaining rock, it was found that the extend of plastic zone and deformation increased compared to the undamaged rock. Therefore the short-term or long-term tunnel stability will be threatened when the rock damage from blasting is ignored in the tunnel stability analysis.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.2 no.2
• /
• pp.50-61
• /
• 2000

The ground around the portal of a tunnel is the most typical part showing the 3-dimensional mechanical behavior in the tunnel. The portal slope is constructed at the weathered soft rock-mass, and remains as a potential sliding mass. The slope failure around the tunnel portal may happen drastically and induce the great disaster; hence, for the permanent stability several special techniques are required. To solve this problem, the ground around the tunnel portal may be excavated in the arch shape to develop the arching effect in horizontal direction. With the arch-type portal slope, one can reduce considerably the excavation mass and the damage of environments. This approach has not been attempted yet due to the lack of understanding and the well-defined analyzing method, so the retaining wall type portal is more universal. The 3-dimensional finite element analyses were carried out to prove that the arch type is more advantageous in safety and cost than the right angle type. The influence of the tunnel construction sequence and the strength of the rock-mass on the slope stability was investigated by focusing on the maximum shear strain in the slope, and the yield zone at the tunnel face.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.87-96
• /
• 2004

Application of the soil nailing method is continuously extending in maintaining stable excavations and slopes. However, ground anchor support system occasionally may not be used because of space limitations in urban excavation sites nearby the existing structures. In this case, soil nailing system with relatively short length of nails could be efficiently adopted as an alternative method. The general soil nailing support system, however, may result in excessive deformations particularly in an excavation zone of the existing weak subsoils. Pretensioning the soil nails then could play important roles to reduce deformations mainly in an upper part of the nailed-soil excavation system as well as to improve local stability. In this study, a newly modified soil nailing technology named as the PSN (Pretension Soil Nailing) is developed to reduce both facing displacements and ground surface settlements in top-down excavation process as well as to increase the global stability. Up to now, the PSN system has been investigated mainly focusing on an establishment of the design procedure. In the present study, laboratory model tests are carried out to investigate the failure mechanism and behavior characteristics of the PSN system. Various results of model tests are also analyzed to provide a fundamental basis for the efficient design.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.9
• /
• pp.133-144
• /
• 2004

Pre-reinforcement ahead of a tunnel face using long steel or FRP (Fiberglass Reinforced Plastic) pipes in NATM(New Austrian Tunnelling Method), known as the RPUM(Reinforced Protective Umbrella Method) or UAM (Umbrella Arch Method), is the promising method to sustain the stability of a shallow tunnel face and reduce the ground settlements. In addition, horizontal reinforcing of the face is recently emphasized to improve the stability of the face. However, the characteristics on longitudinal arching around the face have not yet been established quantitatively with the RPUM (crown-reinforcing) and/or the face horizontal reinforcing. In this study, therefore, the behavior of cohesionless soil around the face reinforced by the reinforcing member representing the RPUM and horizontal reinforcing is investigated through two-dimensional laboratory model tests. A series of tests were carried out on various conditions by changing lengths and angles of the reinforcing members. Based on the vertical pressure around the face, the characteristics of longitudinal arching have been found for the case of the non-reinforced and the reinforced.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.23 no.4
• /
• pp.173-183
• /
• 2020

In the midst of the aging of underground facilities in urban areas and anxiety about road excavation safety accidents, the Ministry of Land, Infrastructure and Transport began to build Underground Geospatial Infomation Map from 2015 as part of the 「ground subsidence prevention measures」 and efficient use of underground spaces. So, the scope is spreading every year. The current Underground Geospatial Infomation Map information is web-based and is operated in a desktop environment, so it is true that there are some limitations in its use in a field environment such as an excavation construction site. The Underground Geospatial Infomation Map, built and operated in a web-based environment, is a large-scale 3D data. Therefore, in order to service by transmitting data to the field without delay, it is necessary to lighten the Underground Geospatial Infomation Map data. In addition, the current Underground Geospatial Infomation Map is not unified in data formats such as 3DS and COLLADA, and the coordinate system method is also different in relative coordinates and absolute coordinates. In this study, by analyzing domestic and overseas prior research and technical use cases, a mobile Underground Geospatial Infomation Map data format and a lightweight method were presented, and a technology development was conducted to create a mobile underground space integration map in the presented format. In addition, the weight reduction rate was tested by applying 3D data compression technology so that data can be transmitted quickly in the field, and technology was developed that can be used by decompressing 3D data compressed in the field. finally, it aims to supplement the technology experimentally developed in this study and conduct additional research to produce it as software that can be used in the excavation site and use it.