• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.96-107
• /
• 2014

Korea Aerospace Research Institute has a plan to launch experimental lunar orbiter in 2017, and lunar orbiter and lander in 2020. In the mission planning phase, LOI(Lunar Orbit Insertion) maneuver strategy should be designed using finite burn model because on-board propulsion system of lunar orbiter in finite burn type. LOI maneuver plan and amount of required ${\Delta}V$ using finite burn model depend on the spacecraft attitude at burn, a type of propellant, thrust level and burn timing. This paper describes the LOI maneuver of lunar orbiter of foreign space agency and then comes up with the LOI maneuver plan of Korean lunar orbiter. Adequate thrust level and burn duration of Korean lunar orbiter also present by performing simulation.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.3
• /
• pp.211-217
• /
• 2012

In this paper, experimental tests and theoretical studies were carried out to evaluate the tensile behavior of the sprayed FRP composite with chopped glass fiber. For this, a series of tensile strength tests with various strain rates were conducted on the specimens of the matrix and sprayed FRP composite. Sprayed FRP composite contained chopped glass fibers with fiber length of 15mm and a specific volume fraction of fibers of 25 %. An inverse simulation was conducted to simulate the strain rate sensitivity based on the present experimental data of the epoxy resin. The simulated viscosity value is adapted to the micromechanics-based viscoelastic damage model(Yang et al., 2012), and the overall tensile behavior of sprayed FRP composites is predicted. It was seen from the comparative study between present experimental data and predication results that the proposed methodology can be used to predict the viscoelastic behavior of the sprayed FRP composite.

• Journal of architectural history
• /
• v.19 no.5
• /
• pp.81-98
• /
• 2010

In the middle of the 8th century, we met the new high-rise building, the 7th storied wooden pagodas in 'Kokubunji' in Japan. I tried to analyze and study this building to show how the wooden pagoda had changed itself because of appearance of new style. The conculusions are as follows; 1. The construction of the foundation was mainly composed namely 'Panchuk'. It was proceeded by two ways. One is the earthen-digging, laying foundations named 'Gulkwangpachuk' and the other is simply laying foundation named 'Jisangpanchuk'. In that period, due to the progress of the technique, we assumed that the main stream is 'Jisangpanchuk'. 2. The elevation of base was mostly the single foundation from archaeological study. The material was stone. The middle case of pagoda had the base of tile-roofed. We knew the just one pagoda had the base of brick, but that was not main stream. 3. The new device had appeared in the central base stone. It was the stone point. But in that period the existing method, a hole style and the new style was used in the central base stone. This fact is showed that the central government was not hold the reigon(it names 'Kook') in the respect of the technique. 4. The plan scale is classified of 3 group. As a result, the first body is larger, the main-unit and the sub-unit is a equal unit. But smaller, the length of main-unit is longer than the one of sub-unit. And the very small pagoda was build in that period.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2008.05a
• /
• pp.137-138
• /
• 2008

• Ceramist
• /
• v.12 no.4
• /
• pp.78-88
• /
• 2009

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1061-1066
• /
• 2011

In this study, the flow characteristics of an injection nozzle installed in a high-pressure holder for improving productivity were determined. The inlet velocity, nozzle inflow angle, and nozzle outlet diameter were selected as design factors having an influence on the flow characteristics, and numerical analysis was conducted for these factors. As the inlet velocity is high and the nozzle outlet diameter is small, the pressure and velocity of the injected flow are high. In the case of the nozzle inflow angle, the variation of flow characteristics according to angle was slight, but the highest pressure and velocity were found at $15^{\circ}$. In addition, the possibility of chip elimination by the injected flow was analyzed on the basis of the numerical results.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.9
• /
• pp.1255-1266
• /
• 1998

Effects of a length-to-diameter ratio, L/D, on the three-dimensional flow and aerodynamic loss within an injection hole, which is normally oriented to the mainflow, have been investigated by using a straight five-hole probe. The length-to-diameter ratio of the injection hole is varied to be 0.5 and 2.0 for blowing ratios of 0.5, 1.0 and 2.0. Regardless of the blowing ratio, flows within the hole and at the jet exit are strongly affected by the length-to-diameter ratio. In the case of L/D=0.5, the inside flow is considerably influenced by the mainflow, and the exit flow variation is found to be the greatest. The aerodynamic loss in this case is usually attributed to jet -mainflow interactions. In the case of L/D=2.0, the flow separation and reattachment in the inlet region are completely separated from the complicated exit flow, and the aerodynamic-loss production is mainly due to the inlet flow separation.

• Journal of computational fluids engineering
• /
• v.4 no.3
• /
• pp.21-27
• /
• 1999

In this paper, tile characteristics of flow resulting from the configurations of piston head and intake-port of the cylinder in a gasoline-direct-injection engine are investigated numerically. Calculations are carried out from intake process to the end of compression. GTT code which includes the third order upwind Chakravarthy-Osher TVD scheme and κ-ε turbulence model with the law of wall as a boundary condition. As a result, a piston head with a smaller radius of curvature and larger radius gives stronger reverse tumble. It is also shown that as the maximum tumble ratio increases by the configuration of the intake-port the tumble ratio at the end of compression stroke increases. It is concluded that flows at the end of compression stroke can be controlled by the optimum design of intake-port and piston head.

• Journal of ILASS-Korea
• /
• v.6 no.4
• /
• pp.39-48
• /
• 2001

The Gasoline Direct Injection(GDI) system has been highlighted due to the improvement of fuel consumption and the control of exhaust emission from gasoline engines. Main purpose of the present study is to measure spray characteristics of GDSI for real engine application. We have investigated experimentally spray tip penetration, spray angle, tip velocity and spatial spray distribution. Counter-rotating vortex grown on the spray surface plays an important role in the spray characteristics. Accordingly the spray tip penetration and tip velocity do not excess 50mm, 20m/s respectively, under 0.6MPa ambient pressure. the spray cone angle of GDSI have a same tendency to a simplex swirl atomizer.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.6
• /
• pp.793-798
• /
• 2011

In this study, it was grasped to the flow characteristics of cutting fluid injected by nozzle installed in high pressure holder for avoiding chip curling occurred during machining process. And for avoiding chip curling, the possibility of elimination under various chip conditions was checked. Consequently, the highest discharging pressure and velocity was shown in 150 of nozzle inflow angle. Also as nozzle outlet diameter is small, the pressure and velocity of injected flow are high. Moreover, It could be confirmed that width and thickness of chip have no direct effect on chip elimination and it is achieved by torque generated by injected cutting fluid.