• Magazine of the Korea Concrete Institute
• /
• v.3 no.2
• /
• pp.115-121
• /
• 1991

Slippage of beam longitudinal reinforcement at beam-column connections is an important cause of damage to reinforced concrete frames under static and dynamic loads, This paper summarizes the results of an experimen¬tal study on the effects of confinements and compressive strength of concrete on the local bond stress-slip cha¬racteristics of deformed bars. I t is concluded from experimental results that, as far as the bond splittmg cracks are restrained by the vertical column reinforcement, confinement of concrete by transverse reinforcement has insignigicant direct effect on the local bond behavior. The ultimate bond strength, however, Increases pro¬portionally with the square root of concrete compressive strength. An empirical model was developed for local bond st ressslip relationslip of deformed bars in confined concrete of different compressive strengths.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.30 no.2
• /
• pp.31-43
• /
• 1993

본 연구에서는 힁부재가 없는 AFRAMAX급 신구조 방식의 유조선을 개발하고자 하였다. 설계의 기본 개념은 1) 이중선체구조를 채용하여 해난사고 발생시 기름유출 방지를 피하고, 2) 힁부재가 없는 극히 단순한 선체구조를 채용하여 용접 로봇등을 활용한 자동건조 비율을 높임으로써 건조 생산성을 향상시키는데 주안점을 두고 있다. 설계 결과 얻어진 선체구조는 기존의 유조선 구 조와 매우 상이하다. 초기구조설계단계에서 구조 부재의 치수는 기존의 선급설계 지침을 활용 하여 결정하였으나, 기존의 유조선 구조와 비교하여 구조배치가 크게 바뀌어 졌기 때문에 기존의 선급설계지침을 만족했다고 해서 구성부재와 국부구조뿐만 아니라 구조 전체적으로도 충분한 구조안전성을 가지고 있는지는 확실치 않다. 따라서 직접구조해석에 의한 구조안전성 평가가 필수적으로 요구되며, 이를 위해 저자들은 선체구조의 최종 종강도(ultimate longitudinal strength), 최종 힁강도(ultimate transverse strength) 및 최종 국부강도(ultimate local strength )를 기준으로한 구조안전성 평가를 수행하였다. 본 논문에서는 이들 중에서 국부 구조부재에 대한 안전성평가 문제만을 다루었다. 결론적으로, 본 연구에서 개발한 선체구조는 건전상태(intact condition)하에서 뿐만 아니라 손상상태하에서도 구조부재는 좌굴 또는 붕괴하지 않고 전반적 으로 충분한 구조안전성을 가지고 있다는 결론을 내릴 수 있었다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.4
• /
• pp.279-285
• /
• 2012

In this paper a computational method for a homogenized peridynamics description of unidirectional fiber-reinforced composites is presented. For these materials, dynamic brittle fracture and damage are simulated with the proposed peridynamic model. Compared with observations from dynamic experiments by Coker et al.(2001), the peridynamic computational model can reproduce various characteristics of dynamic fracture and supersonic or intersonic crack growth in asymmetrically loaded unidirectional fiber-reinforced composite plates. Also we analyze the same model in the symmetric loading condition and figure out that the asymmetric loading leads to a much higher propagation speed. Consistent results have been reported in the experiments.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.1
• /
• pp.35-46
• /
• 1998

Structural damage is used to be modeled through reductions in the stiffness of structural elements for the purpose of damage estimation of structural system. In this study, the concept of joint damage is employed for more realistic damage assessment of a steel structure. The joint damage is estimated damage based on the mode shape informations using neural networks, The beam-to-column connection in a steel frame structure is represented by a rotational spring at the fixed end of a beam element. The severity of joint damage is defined as the reduction ratio of the connection stiffness with respect to the value of the intact joint. The concept of the substructural identification is used for the localized damage assessment in a large structure. The feasibility of the proposed method is examined using an example with simulated data. It has been found that the joint damages can be reasonably estimated for the case with the measurements of the mode vectors subjected to noise.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.142.1-142.1
• /
• 2015

웨이퍼 표면에서 부유 전위 분포를 측정하기 위해서 웨이퍼형 탐침 배열을 제작하고 측정회로를 만들었다. 아르곤 플라즈마의 경우 낮은 압력에서 부유 전위의 분포는 중심에서 최대값을 갖는 포물선 형태로 나타났다. 하지만 음이온 가스의 압력이 증가함에 따라 부유 전위의 분포가 현저하게 변화했다. 가스 압력이 높아짐에 따라 비국부적이었던 플라즈마의 방전 특성이 국부적으로 변화했기 때문이다. 이외에도 음이온도 부유 전위의 분포를 변화시킬 수 있음을 확인하였다. 이 연구는 반도체 제조 공정에서 웨이퍼 표면에서 전하 축적에 의한 손상을 이해하는데 도움이 될 것으로 기대된다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.14 no.5
• /
• pp.462-471
• /
• 1989

Two-dimensional median filters were affectively supprssing the noise in image processing with the adge smearing decreased. However, if the window were large as necessary in noise then the filter had tendency to cut off corners. An estimate of gradient was used to decide how the ouputs of the filters were calculated. For parallel to the gradient direction we used edge preserving median operation and orthogonal to that averaging subfilters over which medians were then chosen. Four different algorithms were introduced.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.194-197
• /
• 2006

This study represents results of fragility curve development for 4-span continuous bridge. 2 type bridge model is chosen frame type and 2-roller 1-hinge type. To research the response of bridge under earthquake excitation, Monte Carlo simulation is performed to study nonlinear dynamic analysis. For nonlinear time history analysis a set of 150 synthetic time histories were generated. Fragility curves in this study are represented by lognormal distribution functions with two parameters and developed as a function of PGA. Five damage states were defined to express the condition of damage based on the actual experimental damage data of bridge column. As a result of this research, the value of damage probability corresponding to each damage state were determined and frame type bridge are favorable under seismic event.

• Journal of the Korea Concrete Institute
• /
• v.21 no.2
• /
• pp.121-127
• /
• 2009

The failure behavior of RC structure was exceedingly affected by the size and the local strain distribution of the failure zone due to the strain localization behavior on the tension softening materials. However, it is very difficult to quantify and assess the local strain occurring in the failure zone by the conventional test method. In this study, image processing technology, which is available to measure the strain up to the complete failure of RC structures, was used to estimate the local strain distribution and the size of failure zone. In order to verify the reliability and validity for the image processing technology, the strain transition acquired by the image processing technology was compared with strain values measured by the concrete gauge on the uniaxial compressive specimens. Based on the verification of image processing technology for the uniaxial compressive specimens, the size and the local strain distribution of the failure zone of deep beam was measured using the image processing technology. With the results of test, the principal tensile/compressive strain contours were drawn. Using the strain contours, the size of the failure zone and the local strain distribution on the failure of the deep beam was evaluated. The results of strain contour showed that image processing technology is available to assess the failure behavior of deep beam and obtain the local strain values on the domain of the post-peak failure comparatively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.7
• /
• pp.883-889
• /
• 2014

It is generated for cavitation erosion due to the local static boiling by pressure differentials in high speed rotating fluid environment. The cavitation is influenced by various elements such as pressure, velocity, temperature, pH of fluid and medium. In particular, the damage of material is accelerated due to the electrochemical corrosion by $C1^-$ and cavitation erosion due to cavities in seawater. In this paper, hence, it investigated for martensite stainless steel the damage behavior with applied current density and cavitation time in natural seawater solution. Less damage depth at the cavitation condition was observed than static condition as a result of galvanostatic experiment. Furthermore, it was shown that dramatic increase of weightloss, damage rate and damage depth after 3 hour of cavitation test.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.5 s.60
• /
• pp.613-625
• /
• 2002

This paper aimed to investigate the damage process of steel parts experiencing failure under strong repeated loading. Likewise, a damage index using various factors related to the damage was proposed. An analysis method for evaluating the damage state was also developed. The damage assessment method focused on the local strain history at the cross-section of the heaviest concentration of deformation. Cantilever-type steel parts were analyzed under uniaxial load combined with a constant axial load, considering horizontal displacement history, Loading patterns and steel types were considered as the main parameters in analyzing the models. The effects of the parameters on the failure modes, deformation capacity, and damage process as seen from the analysis results were also discussed. Each failure process was compared as steel types. In addition, the failure of steel parts under strong repeated loading was determined according to loading. Results revealed that the state of the failure is closely related to the local plastic strain.