• Journal of the Korean Chemical Society
• /
• v.40 no.4
• /
• pp.219-228
• /
• 1996

An ab initio molecular orbital method has been applied to investigation of molecular properties and equilibrium geometries for hexahydroxybenzene triscarbonate (C9O9) and its analogous cyclic compounds (C9S9, C9O6S3, C9O3S6). In these works, the optimized geometry of each compound has been obtained at HF and MP2 levels. These results have shown that the optimized geometries of these compounds prefer D3h planar structure to C3v bowl structure. Calculations of harmonic vibrational frequencies have been also carried out at HF/3-21G* level to analyze normal modes of these compounds. Bonding characters of these compounds are studied by Mulliken and natural populations obtained at HF/6-31G* level. We have also studied the structures and the populations of C6O6 and C6S6 at HF and MP2 levels which are obtained by pyrolyses of C9O9 and analogous compounds. In addition, the single point calculations have been performed to predict the approximate energy barrier for pyrolysis of each compound.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.451-459
• /
• 2021

The purpose of this study is to evaluate the performance of a solidifying agent for recycling the fine powder separated from the nuclear power plant decommissioned concrete as a solidifying agent(SA) for radioactive waste. In order to evaluate the performance of the solidifying agent, a powder simulating the fine powder of waste concrete separated from the dismantled concrete of a nuclear power plant was produced, and the main variables were the type of binder and the replacement ratio of zeolite. The solidifying agent was evaluated for fluidity performance, compressive strength, and leaching resistance to non-radioactive cesium. The compressive strength of SA increased as the zeolite replacement ratio increased, and the SA containing 5% or more of zeolite showed a compressive strength that was 1.4 to 1.7 times higher than the acceptance criteria. The cesium leaching index of all specimens was 6 or higher, satisfying the acceptance criteria, and the leaching index of SA was 1.47~1.63 times higher than that of OPC. In particular, the average leaching index after 28 days of the 5% zeolite-substituted solidifying agent was 9.15, which was improved by about 6.4% compared to OPC, and it was confirmed that the zeolite was effective in improving the leaching resistance to cesium ions by showing stable performance over the entire period.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.525-530
• /
• 2019

The performance and stability of solid oxide fuel cells (SOFCs) depend on the microstructure of the electrode and electrolyte. In anode, porosity and pore distribution affect the active site and fuel gas transfer. In an electrolyte, density and thickness determine the ohmic resistance. To optimizing these conditions, using costly method cannot be a suitable research plan for aiming at commercialization. To solve these drawbacks, we made high performance unit cells with low cost and highly efficient ceramic processes. We selected the NiO-YSZ cermet that is a commercial anode material and used facile methods like die pressing and dip coating process. The porosity of anode was controlled by the amount of carbon black (CB) pore former from 10 wt% to 20 wt% and final sintering temperature from $1350^{\circ}C$ to $1450^{\circ}C$. To achieve a dense thin film electrolyte, the thickness and microstructure of electrolyte were controlled by changing the YSZ loading (vol%) of the slurry from 1 vol% to 5 vol. From results, we achieved the 40% porosity that is well known as an optimum value in Ni-YSZ anode, by adding 15wt% of CB and sintering at $1350^{\circ}C$. YSZ electrolyte thickness was controllable from $2{\mu}m$ to $28{\mu}m$ and dense microstructure is formed at 3vol% of YSZ loading via dip coating process. Finally, a unit cell composed of Ni-YSZ anode with 40% porosity, YSZ electrolyte with a $22{\mu}m$ thickness and LSM-YSZ cathode had a maximum power density of $1.426Wcm^{-2}$ at $800^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.4
• /
• pp.597-605
• /
• 2019

IPM bridge is an integral bridge that can be applied from span 30.0m up to 120.0m, the shape conditions of IPM bridge is also applicable to the rahmen bridge. In this study, to perform the structural analysis of Rahmen bridge and IPM Bridge, the researchers compared the distribution types such as load, moment, and displacement of those bridges. Structural analysis was carried out on four span models ranging from single span bridges to four spans of 120.0 m, based on span length of 30.0 m. Structural analysis was carried out on those bridge with span 30.0m up to 120.0m. The conclusions drawn from this study are as follows. 1) The bending moments were calculated to be large for the Rahmen bridge, and the horizontal displacements were estimated to be large for the IPM bridge. 2) Since the bending moments are derived by the span length rather than the extension of the bridge, the permissible bending moment for the span length should be considered in the design. 3) The pile bent of the IPM bridge did not exceed the plastic moment of the steel pipe pile at 120.0m span, but because the horizontal displacement in the shrinkage direction is close to 25mm, the design considerations are needed. 4) In the actual design, it is important to ensure stability against member forces, so review of the negative moment is most important.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.1
• /
• pp.33-40
• /
• 2021

In recent years, many construction projects become large and complicated, and construction accidents also steadily increase, which grows interest in the safety and maintenance during construction. Many of the construction accidents are related to temporary construction and structures, but the safety evaluation and management during construction are unclear and indefinite due to the short operating period and continuous change in the formation of the temporary structure. The system support, which is one of the temporary structures to support the pouring load of concrete, was proposed to easily install and dismantle members with connection parts pre-manufactured. The use of the system support is increasing to improve the safety of the temporary structure during construction. However, the system support, which consists of multiple members, still has uncertainties in connectivity between members and supports of vertical members. Therefore, this study analyzed the structure, load, and accident cases of the system support to define the damage scenarios for member connection, support condition, and lateral displacement. The decrease rate of the critical load was analyzed according to the damage scenarios based on the defined unit structure of the system support. In addition, this study provided vulnerable members for each damage scenario, which could induce instability of the temporary structures during design, construction, and operation of the structure.

• Journal of the Korean Electrochemical Society
• /
• v.25 no.4
• /
• pp.184-190
• /
• 2022

Spinel LiMn₂O₄ (LMO) and layered LiNi_0.5Co_0.2Mn_0.3O₂ (NCM) are widely used as positive electrode materials for lithium-ion batteries. LMO and NCM positive electrode materials have a complementary properties. LMO has low cost and high safety and NCM materials show a relatively high specific capacity and better cycle life even at elevated temperature. Therefore, the LMO and NCM active materials are blended and used as a positive electrode in large-size batteries for electric vehicles (xEV). In this study, the cycle performance of a blended electrode prepared by simply mixing LMO and NCM and a bi-layer electrode in which two electrode layers aree sequentially coated are compared. The bi-layer electrode prepared by composing the same ratio of both active materials has similar capacity and cycle performance to the blend electrode. However, the LN electrode coated with LMO first and then NCM is the best in the full cell cycle performance at elevated temperature, and the NL electrode, in which NCM is first coated with LMO has a faster capacity degradation than the blended electrode because LMO is mainly located on the top of the electrode adjacent to electrolyte and graphite negative electrode. Also, the LSTA (linear sweep thermmametry) analysis results show that the LN bi-layer electrode in which the LMO is located inside the electrode has good thermal stability.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.9-16
• /
• 2016

A position control system composed of the PMLSM(Permanent Magnet Linear Synchronous Motor), unlike conventional linear permanent magnet synchronous motor is fixed to the permanent magnet moving coil rails (permanent magnet = stator, coil = mover), the coil is fixed, moving the permanent magnet, we propose a position control system (permanent magnet = mover, coil = stator) structure. Position is measured not using conventional encoder or resolver but by adopting vector control method using 2 hall sensors generating rectangular signal. This method estimate the velocity and position of mover by using the quadruple of two hall sensor signal instead of encoder signal. Vector control of PMLSM using 2 hall sensor generating rectangular wave is proved to control the system stable and efficiently through simulation. Also hardware experiment reveals that the position control performance is measured within the range of $30{\sim}50{\mu}m$ in the accuracy of $10{\sim}20{\mu}m$, which is improved twice to the conventional method. The proposed method exhibits its economical efficiency and practical usefulness. The vector control technique using two hall sensors can be installed in narrow place, accordingly it can be implemented on the system where the conventional encoder or resolver cannot operate.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.251-258
• /
• 2012

Recently, NAND Flash memory structure is evolving from SDR (Single Data Rate) to high speed DDR(Double Data Rate) to fulfill the high performance requirement of SSD and SSS. Accordingly, the proper ways of transferring data that latches valid data stably and minimizing data skew between pins by using PHY(Physical layer) circuit techniques have became new issues. Also, rapid growth of speed in NAND flash increases the operating frequency and power consumption of NAND flash controller. Internal voltage variation margin of NAND flash controller will be narrowed through the smaller geometry and lower internal operating voltage below 1.5V. Therefore, the increase of power budge deviation limits the normal operation range of internal circuit. Affection of OCV(On Chip Variation) deteriorates the voltage variation problem and thus causes internal logic errors. In this case, it is too hard to debug, because it is not functional faults. In this paper, we propose new architecture that maintains the valid timing window in cost effective way under sudden power fluctuation cases. Simulation results show that the proposed technique minimizes the data skew by 379% with reduced area by 20% compared to using PHY circuits.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.311-311
• /
• 2016

최근 고성능 디스플레이 개발이 요구되면서 기존 비정질 실리콘(a-Si)을 대체할 산화물 반도체에 대한 연구 관심이 급증하고 있다. 여러 종류의 산화물 반도체 중 a-IGZO (amorphous indium-gallium-zinc oxide)가 높은 전계효과 이동도, 저온 공정, 넓은 밴드갭으로 인한 투명성 등의 장점을 가지며 가장 연구가 활발하게 보고되고 있다. 기존에는 SG(단일 게이트) TFT가 주로 제작 되었지만 본 연구에서는 DG(이중 게이트) 구조를 적용하여 고성능의 a-IGZO 기반 박막 트랜지스터(TFT)를 구현하였다. SG mode에서는 하나의 게이트가 채널 전체 영역을 제어하지만, double gate mode에서는 상, 하부 두 개의 게이트가 동시에 채널 영역을 제어하기 때문에 채널층의 형성이 빠르게 이루어지고, 이는 TFT 스위칭 속도를 향상시킨다. 또한, 상호 모듈레이션 효과로 인해 S.S(subthreshold swing)값이 낮아질 뿐만 아니라, 상(TG), 하부 게이트(BG) 절연막의 계면 산란 현상이 줄어들기 때문에 이동도가 향상되고 누설전류 감소 및 안정성이 향상되는 효과를 얻을 수 있다. Dual gate mode로 동작을 시키면, TG(BG)에는 일정한 positive(or negative)전압을 인가하면서 BG(TG)에 전압을 가해주게 된다. 이 때, 소자의 채널층은 depletion(or enhancement) mode로 동작하여 다른 전기적인 특성에는 영향을 미치지 않으면서 문턱 전압을 쉽게 조절 할 수 있는 장점도 있다. 제작된 소자는 p-type bulk silicon 위에 thermal SiO2 산화막이 100 nm 형성된 기판을 사용하였다. 표준 RCA 클리닝을 진행한 후 BG 형성을 위해 150 nm 두께의 ITO를 증착하고, BG 절연막으로 두께의 SiO2를 300 nm 증착하였다. 이 후, 채널층 형성을 위하여 50 nm 두께의 a-IGZO를 증착하였고, 소스/드레인(S/D) 전극은 BG와 동일한 조건으로 ITO 100 nm를 증착하였다. TG 절연막은 BG 절연막과 동일한 조건에서 SiO2를 50 nm 증착하였다. TG는 S/D 증착 조건과 동일한 조건에서, 150 nm 두께로 증착 하였다. 전극 물질과, 절연막 물질은 모두 RF magnetron sputter를 이용하여 증착되었고, 또한 모든 patterning 과정은 표준 photolithography, wet etching, lift-off 공정을 통하여 이루어졌다. 후속 열처리 공정으로 퍼니스에서 질소 가스 분위기, $300^{\circ}C$ 온도에서 30 분 동안 진행하였다. 결과적으로 $9.06cm2/V{\cdot}s$, 255.7 mV/dec, $1.8{\times}106$의 전계효과 이동도, S.S, on-off ratio값을 갖는 SG와 비교하여 double gate mode에서는 $51.3cm2/V{\cdot}s$, 110.7 mV/dec, $3.2{\times}108$의 값을 나타내며 훌륭한 전기적 특성을 보였고, dual gate mode에서는 약 5.22의 coupling ratio를 나타내었다. 따라서 산화물 반도체 a-IGZO TFT의 이중게이트 구조는 우수한 전기적 특성을 나타내며 차세대 디스플레이 시장에서 훌륭한 역할을 할 것으로 기대된다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.55 no.2
• /
• pp.156-163
• /
• 2017

People with class I intellectual disability need lifelong assistance and protection from their surroundings due to impaired adaptive functioning. They have poor oral health and show higher prevalence of dental caries, periapical inflammation and tooth loss that require proper prosthetic restoration. Because removable prostheses for intellectually disabled patients often lack stability, retention, and maintenance, fixed prostheses are essential and the only available option is dental implants. In this case, a 45 year-old male patient with class I intellectual disability had poor oral hygiene with most of his teeth missing and visited the clinic to recover his masticatory function. Due to such systemic conditions, the definitive restoration of choice was the implant-supported fixed dental prosthesis made of biocompatible and highly strong monolithic zirconia. In consequence of the treatment process, the patient was able to improve his oral environment aesthetically and functionally.