• Journal of the Korea Concrete Institute
• /
• v.24 no.3
• /
• pp.275-283
• /
• 2012

Steel Plate for Rebar Connection was recently developed to splice rebars in delayed slab-wall joints in high-rise building, slurry wall-slab joints, temporary openings, etc. It consists of several couplers and a thin steel plate with shear key. Cyclic loading tests on slab-wall joints were conducted to verify structural behavior of the joints having Steel Plate for Rebar Connection. For comparison, joints with Rebend Connection and without splices were also tested. The joints with Steel Plate for Rebar Connection showed typical flexural behavior in the sequence of tension re-bar yielding, sufficient flexural deformation, crushing of compression concrete, and compression rebar buckling. However, the joints with Rebend Connection had more bond cracks in slabs faces and spalling in side cover-concrete, even though elastic behavior of the joints was similar to that of the joints with Steel Plate for Re-bar Connection. Consequently, the joints with Rebend Connection had less strengths and deformation capacities than the joints with Steel Plate for Re-bar Connection. In addition, stiffness of the joints with Rebend Connection degraded more rapidly than the other joints as cyclic loads were applied. This may be caused by low elastic modulus of re-straightened rebars and restraightening of kinked bar. For two types of diameters (13mm and 16mm) and two types of grades (SD300 and SD400) of rebars, the joints with Steel Plate for Rebar Connection had higher strength than nominal strength calculated from actual material properties. On the contrary, strengths of the joints with Rebend Connection decreased as bar diameter increased and as grade becames higher. Therefore, Rebend Connection should be used with caution in design and construction.

• Journal of Environmental Impact Assessment
• /
• v.28 no.5
• /
• pp.492-506
• /
• 2019

Heavy metal contaminants in the shooting range are mostly present in a warhead circle or a metal fragment present as a particle, these fine metal particles are weathered for a long period of time is very likely that the surface is present as an oxide or carbon oxide. In particular, lead which is a representative contaminant in the shooting range soil, is present as more fine particles because it increases the softness and is stretched well. Therefore, by physical washing experiment, we conducted a degree analysis, concentration of heavy metals by cubic diameter, composition analysis of metallic substances, and assessment of applicability of gravity, magnetism and floating selection. The experimental results FESEM analysis and the measurement results lead to the micro-balance was confirmed thatthe weight goes outless than the soil ofthe same size in a thinly sliced and side-shaped structure according to the dull characteristics it was confirmed that the high specific gravity applicability. In addition, the remediation efficiency evaluation results using a hydrocyclone applied to this showed a cumulative remediation efficiency of 71%,twice 80%, 3 times 91%. On the other hand, magnetic sifting showed a low efficiency of 17%,floating selection -35mesh (0.5mm)target soil showed a relatively high efficiency to 39% -10mesh (2mm) efficiency was only 16%. The target treatment diameter of soil washing should be 2mm to 0.075mm, which is applied to the actual equipment by adding an additional input classification, which would require management as additional installation costs and processes are constructed. As a result, it is found that the soilremediation of shooting range can be separately according to the size of the warhead. The size is larger than the gravel diameter to most 5.56mm, so it is possible to select a specific gravity using a high gravity. However, the contaminants present in the metal fragments were found to be processed by separating using a hydrocyclone of the soil washing according to the weight is less than the soil of the same particle size in a thinly fragmented structure.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.4
• /
• pp.225-232
• /
• 2024

This study focuses on the determination of the fracture mode in composite laminates using deep learning. With the increase in the use of laminated composites in numerous engineering applications, the insurance of their integrity and performance is of paramount importance. However, owing to the complex nature of these materials, the identification of fracture modes is often a tedious and time-consuming task that requires critical domain knowledge. Therefore, to alleviate these issues, this study aims to utilize modern artificial intelligence technology to automate the fractographic analysis of laminated composites. To accomplish this goal, scanning electron microscopy (SEM) images of fractured tensile test specimens are obtained from laminated composites to showcase various fracture modes. These SEM images are then categorized based on numerous fracture modes, including fiber breakage, fiber pull-out, mix-mode fracture, matrix brittle fracture, and matrix ductile fracture. Next, the collective data for all classes are divided into train, test, and validation datasets. Two state-of-the-art, deep learning-based pre-trained models, namely, DenseNet and GoogleNet, are trained to learn the discriminative features for each fracture mode. The DenseNet models shows training and testing accuracies of 94.01% and 75.49%, respectively, whereas those of the GoogleNet model are 84.55% and 54.48%, respectively. The trained deep learning models are then validated on unseen validation datasets. This validation demonstrates that the DenseNet model, owing to its deeper architecture, can extract high-quality features, resulting in 84.44% validation accuracy. This value is 36.84% higher than that of the GoogleNet model. Hence, these results affirm that the DenseNet model is effective in performing fractographic analyses of laminated composites by predicting fracture modes with high precision.

• Journal of Korean Society of Steel Construction
• /
• v.27 no.6
• /
• pp.513-523
• /
• 2015

In steel moment frames constructed of H-shapes, strong-axis moment connections should be used for maximum structural efficiency if possible. And most of cyclic seismic testing, domestic and international, has been conducted for strong-axis moment connections and cyclic test data for weak-axis connections is quite limited. However, when perpendicular moment frames meet, weak-axis moment connections are also needed at the intersecting locations. Especially, both strong- and weak-axis moment connections have been frequently used in domestic practice. In this study, cyclic seismic performance of RBS (reduced beam section) weak-axis welded moment connections was experimentally investigated. Test specimens, designed according to the procedure proposed by Gilton and Uang (2002), performed well and developed an excellent plastic rotation capacity of 0.03 rad or higher, although a simplified sizing procedure for attaching the beam web to the shear plate in the form of C-shaped fillet weld was used. The test results of this study showed that the sharp corner of C-shaped fillet weld tends to be the origin of crack propagation due to stress concentration there and needs to be trimmed for the better weld shape. Different from strong-axis moment connections, due to the presence of weld access hole, a kind of CJP butt joint is formed between the beam flange and the horizontal continuity plate in weak-axis moment connections. When weld access hole is large, this butt joint can experience cyclic local buckling and subsequent low cycle fatigue fracture as observed in this testing program. Thus the size of web access hole at the butt joint should be minimized if possible. The recommended seismic detailing such as stickout, trimming, and thicker continuity plate for construction tolerance should be followed for design and fabrication of weak-axis welded moment connections.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.21 no.1
• /
• pp.11-23
• /
• 2016

An ecological study on subtidal macrobenthic fauna was conducted off the Namhaedo Island, south coast of Korea from July 2012 to April 2013. A total of 247 species of macrobenthos occurred with a mean density of $1,027ind./m^2$ and a mean biomass of $148.7g/m^2$. Polychaetes was the richest and most abundant faunal group that comprised 37% in both total species number and density whereas echinoderms were biomass-dominant faunal group that accounted for 44% of the mean biomass. There was a seasonal variation in the species richness and abundance of macrobenthos with more species in winter and higher density in spring. Mean faunal density was relatively high at the stations near Namhaedo Island, but gradually decreased toward offshore stations. The most dominant species in terms of density was an amphipod species, Eriopisella sechellensis which occurred as a top ranker during three seasons except spring recorded the fourth rank. E. sechellensis showed its high density at the near shore stations of Namhaedo Island, but this species did not occur around the entrance of Gwangyang and Saryang Bays where Theora fragilis and Lumbrineris longifolia showed high densities. In particular, Tharyx sp., recorded high density between Gwangyang Bay entrance and offshore after Sea Prince oil spill, did not occur in the same area during this study period. The bottom temperature and sorting value of the surface sediments were highly correlated to the spatial distribution of macrobenthic fauna from the Bio-Env analysis. From the cluster analysis, the study area has five station groups with more similar faunal affinities from inner area toward offshore area. Based on the SIMPER analysis T. fragilis, Magelona japonica, E. sechellensis, L. longifolia and Paraprionospio cordifolia were mainly contributed to the classification of station groups. From the BPI, benthic communities in the entrance of Gwangyang Bay and Saryang Bay were considered to be in a slightly polluted condition in contrast to the normal healthy community at the offshore of Namhaedo Island. These results suggested that the benthic community of this area should be regularly monitored to assess the health status of this benthic ecosystem.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.3
• /
• pp.99-104
• /
• 2011

A stoichiometric mixture of evaporating materials for $MgGa_2Se_4$ single crystal thin films was prepared from horizontal electric furnace. The crystal structure of these compounds has a rhombohedral structure with lattice constants $a_0=3.953\;{\AA}$, $c_0=38.890\;{\AA}$. To obtain the single crystal thin films, $MgGa_2Se_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperatures were $610^{\circ}C$ and $400^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the double crystal X-ray rocking curve and X-ray diffraction ${\omega}-2{\theta}$ scans. The carrier density and mobility of $MgGa_2Se_4$ single crystal thin films measured from Hall effect by van der Pauw method were $6.21{\times}10^{18}\;cm^{-3}$ and 248 $cm^2/v{\cdot}s$ at 293 K, respectively. The optical absorption of $MgGa_2Se_4$ single crystal thin films was investigated in the temperature range from 10 K to 293 K. The temperature dependence of the optical energy gap of the $MgGa_2Se_4$ obtained from the absorption spectra was well described by the Varshni's equation, $E_g(T)=E_g(0)-({\alpha}T^2/T+{\beta})$. The constants of Varshni's equation had the values of $E_g(0)=2.34\;eV$, ${\alpha}=8.81{\times}10^{-4}\;eV/K$ and ${\beta}=251\;K$, respectively.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.20 no.2
• /
• pp.78-91
• /
• 2015

Macrobenthic community was studied at 87 stations including intertidal and subtidal area in Yoja Bay, south coast of Korea in summer season of July 2001. Duplicate sediment samples were taken using a van Veen grab ($0.1m^2$) in each station. Mud facies of the sediments were widly distributed in the bay. And relatively high content of sand was shown in the Bulgyo-cheon stream estuary. A total of 274 species was occurred with a mean density of $2,346ind./m^2$ and a mean biomass of $78.2g/m^2$. The polychaetes were species- and density-dominant faunal group with a total of 122 species (44.5% of the total number of species), and mean density of $1,543ind./m^2$ (65.8% of the mean density). Meanwhile, molluscs were biomass-dominant faunal group with $44.4g/m^2$. Bio-Env. analysis showed that the combination of bottom salinity and sand content of the surface sediments was highly correlated to the major macrobenthic communities. The macrobenthic species number, decreasing toward inner bay from mouth of the bay, was significantly correlated to the sediment environmental variables and bottom water salinity. The spatial distribution of abundance showed significant correlation to the sand and mud contents and mean grain size of the surface sediments. Major dominant species were Minuspio japonica (polychaete) with a mean density of $1,167ind./m^2$ at upper part of the bay where salinity was low and Eriopisella sechellensis (amphipod) with $152ind./m^2$ in central part of the bay. Species diversity (H') was $3.0{\leq}$ in the mouth part of the bay and ranged 2.0-3.0 in the inner part of the bay, which showed a significant positive correlation to bottom salinity. Total number of species also showed significant correlations to the sediment composition and bottom salinity. Based on the cluster analysis the macrobenthic community of the bay was classified into five station groups from the bay mouth toward the inner part of the bay depending on the species composition. From the SIMPER analysis Minuspio japonica, Eriopisella sechellensis and Sternaspis scutata mainly contributed to the classification of station group. These results suggested that the macrobenthic communities of the bay were mainly influenced by bottom salinity together with sediment composition, and that the studies of spatial distributions of major dominant species and benthic communities should be conducted continuously to monitor the Yeoja Bay benthic environment.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.3
• /
• pp.330-342
• /
• 1998

Benthic environmental parameters were analysed at 40 stations during the period from April 1995 to February 1996. such as water temperature, salinity, and dissolved oxygen (DO)-concentration in the surface and bottom water layers, grain size, chemical oxygen demand (COD), ignition loss, particulate organic carbon (POC) in the sediment of Youngsan River estuary. The water temperature ranged from 4.1 to $29.8^{\circ}C$ in the surface and 4.0 to $20.7^{\circ}C$ in the bottom layers. Salinity ranged from 15.1 to $33.6\%_{\circ}$ in the surface and 31.5 to $33.2\%_{\circ}$ in the bottom layer. The salinity in the outer pan of the study area was higher than that of inner area from autumn to spring, whereas they remained lower in summer. Dissolved oxygen concentration ranged from 5,1 to 11.2 $mg/\ell$ in the surface, and 0.79 to 10,2 $mg/{\ell}$ in the bottom layers. Hypoxic condition ($\le2.0mg/\ell$) was developed in the bottom water layer from Youngsan dike to Mokpo Harhour in summer due to the summer stratification. The surface sediment type was silty clay with a mean grain size of $9.12{\pm}0.45\phi$. The range of COD was from 6.15 to $15.49mgO_2/g$ with a mean of $10.59{\pm}12.64mgO_2/g$. The COD in the inner stations was relatively higher than that of outer stations, and decreased toward the outer part of the study area. Ignition loss (IL) ranged from 3.35 to $15.45\%$ with a mean of $5.96{\pm}1.91\%$. Principal component analysis was carried out from the following five environmental parameters: water temperature, dissolved oxygen in the bottom layer and mean grain size, clay content and COD in the sediment. The forty stations in the study area were classified into three stational groups. Group I was located in the inner part of the estuary characterised by relatively low surface salinity and bottom water temperature, fine sedimemt texture, high organic matter and low dissolved oxygen concentration during the summer. Meanwhile, Group III showing relatively high bottom salinity and water temperature was located in the outer part of the estuary characterising coarse sediment and low organic content in sediment. Group II was between Group I and Group III. The division of the areal groups had high correlations to the DO in the bottom layer and clay content in the sediment.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.5 no.1
• /
• pp.59-69
• /
• 2000

Environmental factors and phytoplankton community have been bimonthly investigated in order to clarify the bioecological characteristics of coral habitats around Moonsom at the southern Cheju Island from September 1995 to July 1996. Annual mean temperature and annual mean salinity were $17.4^{\circ}C$ and 34.06 psu, respectively, showing lower temperature-higher salinity in winter and higher temperature-lower salinity in summer, which means such conditions are inadequate for coral reef formation. Nutrient concentrations represent that total nitrogen ranged from $0.07{\sim}10.08\;{\mu}M$, phosphate from $0.05{\sim}1.70\;{\mu}M$, and silicate from $3.08{\sim}21.86\;{\mu}M$. The N/P ratio showed the range of 9.59-10.60 with decreasing offshore-ward, which means the phytoplankton community could be limited by nitrogen sources. Annual mean euphotic depth was 32.0m (18.9m-48.6m) with difference according to season and reveals the close relationship with the depth of coral distribution. Chlorophyll a concentrations of phytoplankton ranged from $0.12{\sim}1.51\;{\mu}g\;L^{-1}$ and standing crops from $1.5{\times}10^3{\sim}7.0{\times}10^5\;cells\;L^{-1}$, showing higher at inshore than at offshore with a blooming in May. A total of 128 species of phytoplankton occurred in all stations, representing 99 spp. of diatoms, 26 spp. of dinoflagellates, 2 spp. of silicoflagellates and 1 sp. of blue-green algae. Diatoms are main taxa in all seasons except for occupying by dinoflagellates in summer. Among dominant species, fParalia sulcata (Ehrenberg) Cleve and Cylindrotheca closterium (Ehrenberg) Lewin & Reimann were predominant and are likely to be main food sources for coral community. Annual mean species diversity index (H') was 1.84, showing lower than around the coast line of Cheju Island.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.23 no.2
• /
• pp.91-108
• /
• 2018

An ecological study on subtidal macrobenthic fauna was conducted from 25 stations in the estuarine area of Wando-Doam Bay, southern coast of Korea during August 2013. A total of 186 species was collected with a mean density of $1,229ind./m^2$ and a mean biomass of $265.7g/m^2$. Polychaetes showed the richest benthic fauna comprising 43% of total fauna, whereas mollusks appeared as density- and biomass-dominant fauna accounted for 45% and 48% of the mean density and biomass, respectively. The number of species and mean faunal density were relatively higher at the stations surrounded by Sinjido, Joyakdo and Gogeumdo showing a gradual decrease toward inner bay stations. Species number and density were negatively correlated with bottom water temperature, but they were positively correlated with both the bottom salinity and DO. The most dominant species in terms of density was a semelid bivalve, Theora fragilis which showed a positive correlation with TOC content of surface sediment and its high density occurred around Gogeum-Sinji-Joyakdo area where dense aquaculture facilities exist. In the bay mouth area, an amphipod species, Eriopisella sechellensis showed its higher density at the stations with low organic content but fine grains. The combination of water temperature, salinity, pH of bottom water, water and sulfur content of the surface sediment could explain 71% of the spatial distribution of macrobenthic fauna from the Bio-Env analysis. From the cluster analysis, the study area consisted of 6 distinct station groups lineated from offshore area toward inner area. Ampharete arctica, Goniada maculata, Eriopisella sechellensis, Theora fragilis, Caprella sp. were identified as the main contributing faunas in classification by the SIMPER analysis. From the value of BPI, the benthic communities at the inner and central Wando-Doam Bay were assessed to be in a normal condition whereas those at the outer Wando harbor and Gogeum-Sinji-Joyakdo area were assessed in a poor or very poor condition due to the high concentration of particulate organic matter might be originated from the nearby dense aquaculture facilities. This study indicated that pristine inner bay has been influenced by the organic material supplied from the outer bay. Thus it is necessary to establish an ecological management plan to reduce organic enrichment of sediment from dense aquaculture facilities in the outer bay.