• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.2
• /
• pp.287-297
• /
• 2015

In concrete structural design provisons, there is a minimum allowable strain of steel to ensure a ductility of RC members and a c/d is limited for the same purpose in EC2. In general, a ductility capacity of RC members is evaluated by a displacement ductility which is a ratio of ultimate displacement to yield displacement, and it is necessary to calculate accurately a yield displacement and an ultimate displacement to evaluate a displacement ductility. But a displacement in members is affected by various member characteristics, so it is hard to calculate a displacement exactly. In this study, a displacement ductility is calculated by calculating a yield displacement and an ultimate displacement through a moment-curvature relationship. The main variables examined are concrete strength, yield strength, steel ratio, spacing of confinement, axial force ratio and concrete ultimate strain. As results, as a concrete strength is increased, a ductility displacement is increased. But as yield strength, steel ratio, spacing of confinement and axial force ratio are increased, a displacement ductility is decreased. And a displacement ductility is necessary to calculate a response modification factor (R) of columns for seismic design, so it is appeared that it is important to calculate a displacement ductility more accurately.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.5C
• /
• pp.199-210
• /
• 2012

The effects of tunnelling in weak weathered rock on the behaviour of a pre-existing single pile and pile groups ($3{\times}3$ and $5{\times}5$ pile groups) above a tunnel have been studied by carrying out three-dimensional (3D) elasto-plastic numerical analyses. Numerical modelling of such effects considers the response of the single pile and pile groups in terms of tunnelling-induced ground and pile settlement as well as changes of the shear transfer mechanism at the pile-soil interface due to tunnelling. Due to changes in the relative shear displacement between the pile and the soil at the pile-soil interface with tunnel advancement, the shear stresses and axial pile force distributions along the pile change drastically. Based on the computed results, upward shear stresses are induced up to about Z/L=0.775 from the pile top, while downward shear stresses are mobilised below Z/L=0.775, resulting in a reduction in the axial pile force distribution with depth equivalent to a net increase in the tensile force on the pile. A maximum tensile force of about $0.36P_a$ developed on the single pile solely due to tunnelling, where $P_a$ is the service axial pile loading prior to tunnelling. The degree of interface shear strength mobilisation at the pile-soil interface was found to be a key factor governing pile-soil-tunnelling interaction. Overall it has been found that the larger the number of piles, the greater is the effect of tunnelling on the piles in terms of pile settlement, while changes of the axial pile forces for the piles in the groups are smaller than for a single pile due to the shielding effect. The reduction of apparent allowable pile capacity due to tunnelling-induced pile head settlement was significant, in particular for piles inside the groups.

• The Journal of the Korea Contents Association
• /
• v.7 no.12
• /
• pp.262-272
• /
• 2007

SAD (Sum of Absolute Difference) algorithm is the most frequently executing routine in motion estimation, which is the most demanding process in motion picture encoding. To enhance the performance of motion picture encoding on a VLIW processor, an optimal implementation of SAD algorithm on VLIW processor should be accomplished. In this paper, we propose an implementation of optimal scheduling of SAD algorithm with conditional branch on a VLIW-based high performance DSP. We first transform the nested loop with conditional branch of SAD algorithm into a single loop with conditional branch which has a large enough loop body to utilize fully the ILP capability of VLIW DSP and has a conditional branch to make the escape from loop to be achieved as soon as possible. And then we apply a modulo scheduling technique to the transformed single loop. We test the proposed implementation on TMS320C6713, and analyze the code size and performance with respect to processing time. Through experiments, it is shown that the SAD implementation proposed in this paper has small code size appropriate for embedded applications, and the H.263 encoder with the proposed SAD implementation performs better than other H.263 encoder with other SAD implementations.

• Microbiology and Biotechnology Letters
• /
• v.16 no.4
• /
• pp.310-315
• /
• 1988

Two isoenzymes of chorismate mutase(E.C.5.4.99.5) designated as chorismate mutase I(CM I) and chorismate mutase II(CM II), were detected and partially purified from a sp. of intrasporangium isolated from soil. CM I and CM II had pH optima of pH 6.5 and 8.0, respectively and showed the same temperature optimum of 45$^{\circ}C$. The activation energy of the enzymatic reaction was estimated to be 14.7kcal/ mole with CM I and 10.8kcal/mole with CM II. The affinity of isoenzyme CM I for substrate(Km= 1.35mM) was almost the same level as that of CM II(Km = 1.22mM). Both isoenzymes were stable at pH values ranged from pH 6.5 to 9.0, but rapidly denaturated at temperatures above 45$^{\circ}C$. CM II was activated about 7$^{\circ}C$ of its activity by $Ba^{++}$ or $Mg^{++}$ while CM I was slightly inhibited by the same metal ions. Thiol compounds were found not to be necessary for stability of the two enzymes but Co$^{++}$ and EDTA had a little stabilizing effect on CM II only. p-Chloromercuribenzoate strongly inactivated the activities of both enzymes but the reducing agents such as dithiothreitol and L-cysteine protected them against the pCMB inhibition.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.373-379
• /
• 2020

This study performed stress and fatigue life analysis of the damping hinge of a built-in side-by-side refrigerator that occurs when the door is opened to the maximum angle. An analysis of the initial design showed that stress concentration occurred at the corner between the cylinder and upper disk of the bracket pin, and the maximum stress exceeded the yield strength. The maximum stress location and the calculated fatigue life were consistent with the door opening-and-closing endurance test results for a prototype. Three cases of design improvement for the bracket pin were derived with the aim of reducing the stress concentration that appeared in the initial design. An analysis of the cases showed that inserting a fillet between the disk and the cylinder of the bracket pin reduced the stress and increased the fatigue life. Moreover, changing the disk into two steps was more favorable. In conclusion, the best design improvement was the case that the disk was changed to two steps and the fillet with a large radius was inserted. In that case, the stress was the smallest and the fatigue life was infinite.

• Journal of Labour Economics
• /
• v.26 no.2
• /
• pp.97-127
• /
• 2003

The purpose of this paper is to analyze the expected earnings differentials by major of university graduates. Usually the achievement in labor market has been measured by the earnings of those being with job. But such simple comparisons of earnings might fail to bring out correct evaluation once if the probabilities of getting a job are quite different across the major of university graduates. So it is necessary to compare the expected lifetime eatings which can be computed using the earnings of those with job and the probabilities of taking a job. In this paper, we showed that the expected earings of university graduates are quite different by major and not only the difference of earnings but also the difference of job-taking probabilities are considerably contributing such differentials. Especially the expected earnings of medicine and education are considerably higher than those of other majors. These results are maintained almost identically with the change of estimation methods. But despite of these findings. it should be admitted that it was not possible to exactly measure the magnitude of differentials by major.

• The Journal of the Acoustical Society of Korea
• /
• v.19 no.1
• /
• pp.97-102
• /
• 2000

Subband coding is to divide the signal frequency band into a set of uncorrelated frequency bands by filtering and then to encode each of these subbands using a bit allocation rationale matched to the signal energy in that subband. The actual coding of the subband signal can be done using waveform encoding techniques such as PCM, DPCM and vector quantizer(VQ) in order to obtain higher data compression. Most researchers have focused on the error in the quantizer, but not on the overall reconstruction error and its dependence on the filter bank. This paper provides a thorough analysis of subband codecs and further development of optimum filter bank design using vector quantizer. We compute the mean squared reconstruction error(MSE) which depends on N the number of entries in each code book, k the length of each code word, and on the filter bank coefficients. We form this MSE measure in terms of the equivalent quantization model and find the optimum FIR filter coefficients for each channel in the M-band structure for a given bit rate, given filter length, and given input signal correlation model. Specific design examples are worked out for 4-tap filter in 2-band paraunitary filter bank structure. These optimum paraunitary filter coefficients are obtained by using Monte Carlo simulation. We expect that the results of this work could be contributed to study on the optimum design of subband codecs using vector quantizer.

• The Journal of Society for e-Business Studies
• /
• v.18 no.2
• /
• pp.95-110
• /
• 2013

This paper presents a novel feature engineering technique that can improve the conventional machine learning-based text classification systems. The proposed method extends the initial set of features by using hyperlink relationships in order to effectively categorize hypertext web documents. Web documents are connected to each other through hyperlinks, and in many cases hyperlinks exist among highly related documents. Such hyperlink relationships can be used to enhance the quality of features which consist of classification models. The basic idea of the proposed method is to generate a sort of ed concept feature which consists of a few raw feature words; for this, the method computes the semantic similarity between a target document and its neighbor documents by utilizing hierarchical relationships in the WordNet ontology. In developing classification models, the ed concept features are equated with other raw features, and they can play a great role in developing more accurate classification models. Through the extensive experiments with the Web-KB test collection, we prove that the proposed methods outperform the conventional ones.

• Journal of Korea Multimedia Society
• /
• v.13 no.5
• /
• pp.663-673
• /
• 2010

As a tool used for video maintenance, Video segmentation divides videos in hierarchical and structural manner. This technique can be considered as a core technique that can be applied commonly for various applications such as indexing, abstraction or retrieval. Conventional video segmentation used adaptive threshold to split video by calculating difference between consecutive frames and threshold value in window with fixed size. In this case, if the time difference between occurrences of cuts is less than the size of a window or there is much difference in neighbor feature, accurate detection is impossible. In this paper, Improved Adaptive threshold algorithm which enables determination of window size according to video format and reacts sensitively on change in neighbor feature is proposed to solve the problems above. Post-Processing method for decrement in error caused by camera flash and fast movement of large objects is applied. Evaluation result showed that there is 3.7% improvement in performance of detection compared to conventional method. In case of application of this method on modified video, the result showed 95.5% of reproducibility. Therefore, the proposed method is more accurated compared to conventional method and having reproducibility even in case of various modification of videos, it is applicable in various area as a video maintenance tool.

• Journal of Navigation and Port Research
• /
• v.39 no.1
• /
• pp.69-75
• /
• 2015

The concrete purpose of this study is to suggest actually a debt ratio to optimize the capital structure providing a kind of approach to estimate the proper debt ratio with an analytical model and empirical data in Korean shipping industry. The mathematical and analytical model is started from the first equation about ROE, return of net operating income on equity, with an independent variable, debt ratio. It is constructed with several parameters, ROS(return of operating income on sales), TAT(total assets turnover), and NFCL(net finance cost to liabilities). There could not be a certain relationship between debt ratio and ROS or TAT, while some correlation or causality between debt ratio and NFCL. In other words, most of firms with high debt ratio is likely to burden higher finance cost than others with low one. In this case, there is a linearity relationship between debt ratio and NFCL, so then the second equation considering this relation could be included within the analytical approach of this paper. To be short, if the criteria of adequate debt ratio has to be defined as some level of debt ratio to optimize ROE, the ROE could be illustrated as a quadratic equation to debt ratio from two equations. Next, this research estimated those parameters' numbers through the single regression method with data over 12 years of Korean shipping industry, and identified empirically the fact that optimal debt ratio would be approximately 400%. To conclude, if that industry's sales and operating incomes are stable, the debt ratio could be accepted until twice of 200% had forced in order to guarantee its financial safety in past time.