• Journal of the Korean Society for Marine Environment & Energy
• /
• v.2 no.1
• /
• pp.40-48
• /
• 1999

Wave absorbing system is needed at various kinds of wave basins (wave flume, towing tank, square tank) for the model test related to the ocean engineering. In this paper, the performance of wave absorbing system with new concept is estimated throughout the experiments. Herein, the wave absorbing system is designed by punching plate with a given porosity which is installed horizontally and submerged near the water surface. As the incident wave generated by a wave maker advances above a punching plate, the strong jet flow is formed near a hole of punching plate. As a result, wave energy is dissipated into heat energy, Systematic model tests were conducted at KRISO to verify the performance of the wave absorber using a punching plate. It was found that the reflection coefficient of wave absorber is deeply dependent on both the porosity and the submerged depth of a punching plate. Inclined installation of a punching plate shows better performance than a horizontal one within a certain inclined angle.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.543-547
• /
• 2011

Primary water stress corrosion cracking has occurred in dissimilar weld areas in nuclear power plants. Residual stress is a driving force in the crack. Residual stress may be generated by weld or surface machining. Residual stress due to surface machining depends on the machining method, e.g., milling, grinding, or EDM. The stress is usually distributed on or near the surface of the material. We present the measured residual stress for machining on SA 508 and austenitic stainless steels such as TP304 and F316. The residual stress can be tensile or compressive depending on the machining method. The depth and the magnitude of the residual stress depend on the material and the machining method.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.1
• /
• pp.93-101
• /
• 1987

Residual stresses have remained around welding areas of a steel structure member after welding operation. The major causes to occur these residual stresses are the local heat due to a welding, the heat stresses due to a irregular and rapid cooling condition, the material and rigidity of a steel structure. Ultimatly, these residual stresses have been known to decrease a brittle fracture strength, a fatigue strength, a buckling strength, dynamic properties, and the corrosion resistance of the material. This paper deals with the residual stresses on a steel structure member through experimental studies. SWS 58 plates were welded by the method of X-groove type. These plates were layed on the heat treatment at four different temperatures; $350^{\circ}C$, $500^{\circ}C$, $650^{\circ}C$ and $800^{\circ}C$. The resulting residual Stresses were measured by hole drilling method, and the followings were obtained. The residual stresses on the vicinity of a welding point were relieved most effectively at the temperature of $650^{\circ}C$, and these stresses relieved completly when the ratio of a hole diamerter to a hole depth became unity. Hardness test shows that the higher value of hardness at the heat affected zone dropped to belower as the temperature went up from $350^{\circ}C$ to $800^{\circ}C$. The Welding input heats have not influenced the magnitude of residual stresses at the input heat range between above and below one forth than standard.

• The Korean Journal of Ecology
• /
• v.28 no.3
• /
• pp.141-147
• /
• 2005

To clarify seed distribution in sediment and its burial properties of Suaeda japonica, the vertical and horizontal distribution of seeds, organic content of sediment, and sediment content delivered by crabs were studied in mud tidal-flat of Walgot-dong, Siheung, Gyeonggi Province, from March 1999 to October 2000. The 94% and 6% of S. japonica seeds were buried under and outside the maternal plant crown, respectively. Organic matter contents of sediment were higher at the area (17%) covered than at the one (8%) uncovered by S. japonica. In the area covered by S. suaeda, organic matter profiles of sediment showed vertical variation from 19% in surface (1 cm depth) to 14% in 6 cm depth. S. japonica seeds buried in sediment decreased from 45% in 2 mm depth to 0% in 12 mm depth. The density of crabs was higher in the vegetated area than in the non-vegetated one. Especially, the density of Cleistostoma was about 8 times higher in the former than in the latter In the vegetated area, the amount of sediment delivered by crabs was estimated to be 2,409 $cm^3{\cdot}m^{-2}$, and this could ascend the height of sediment to 2.4 mm. Consequently, it might be interpreted that plant debris (organic matters) of maternal plants and sediment delivered by crabs made the S. japonica seeds bury well. By relationship between crab distribution and vegetation, it was thought that crabs got a benefit from S. japonica.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.27 no.4
• /
• pp.255-265
• /
• 1991

In order to find the excavating performance of water-jet nozzle on the sand, the authors were carried out the excavating experiment with the model nozzles which were semi circular sectioned nozzles and rectangular nozzle in water tank. The results were as follows. 1) Excavating maximum depth and width on the sand by the water jet were straightly increased in proportion to the velocity of water jet and the section area of nozzle, and that, by the nozzle distance from the excavating point on the sand, the depth was decreased, while the width was increased straightly. 2) Rectangular nozzle which the thick of hole is 1mm, was a little bit better than the circular nozzle of the same sectioned area on the excavating performance. 3) Empirical equations between the velocity of water jet, the distance of nozzle, and the maximum excavating depth and width by angle of nozzle were expressed as linear, they were as follows on the 45$^{\circ}$ angle of the rectangular nozzle(1$\times$12mm); D=0.0093V sub(0)-0.23H+5.7. W=0.0147V sub(0)+1.06H+10.2. where, D is the maximum excavating depth(cm), W is the maximum excavation width(cm), V sub(0) is the velocity of water jet(cm/s); 926$\leq$V sub(0)$\leq$1504, H is the distance(cm) from nozzle tip to water-jetted point on the surface of sand.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.32-32
• /
• 2000

잠입노즐은 로케트 추진기관의 길이 및 중량을 감소시켜 체계설계의 관점에서 볼 때 많은 이점을 제공한다. 본 연구에서는 3단형 과학로케트 원지점 차넣기 모타(apogee kick motor)에 적용하기위한 잠입노즐의 기초기술 개발에 주안점을 두었다. 고고도에서 저속으로 회전하며 비행하는 원지점 차넣기 모타를 제작하기위해서 체계 요구성능에 의해 예상된 실물형의 50% 크기에 해당하는 축소형 잠입노즐을 제작하였다. 잠입노즐은 잠입부의 내외부가 고온의 추진제 연소가스에 노출된 상태에서 노즐 내부 압력 외에 연소실압에 의한 외부압력이 작용하므로 이를 고려한 열 및 구조설계가 중요하다. 본 연구에서는 노즐 수렴부와 목부에 일체형 그라파이트 소재를 적용하고 확장부 내열재 및 잠입부 배면내열재에 탄소/페놀 복합재를 노즐 내열재로 사용하였다. 그리고 이들의 구조적 지지를 위해 스틸구조물을 적용하였다. 적용된 스틸구조물에는 K형 열전쌍을 이용해 내열재와 구조물 온도를 측정할 수 있는 관통구멍 및 나사부를 구조물 외변에 가공하였다. 열전쌍은 노즐 목직경의 2, 4배 되는 확장부 내열재 단면위치의 2mm와 4mm 깊이와 구조물 내면 및 외면의 4개소에 열전쌍을 부착하여 지상연소시험시 노즐 내열재와 구조물의 온도분포를 관찰한다. 그리고 노즐 조립시 확장부 내열재와 구조물에 각 각 반원형 홈을 내어 여분의 접착제가 원형 홈에 밀려들어가 경화되어 노즐 기밀유지와 체결력을 향상시킬 수 있는 원형공간 접착제 충전 공법을 적용하여 실제모타에 대한 적용가능성을 지상연소시험을 통해 확인한다.

• Korean Journal of Environmental Biology
• /
• v.18 no.1
• /
• pp.133-144
• /
• 2000

The Brentidae is characterized by the reduced labial palpi, which is located in cavities on the apicoental margin of the prementum. The postcoila of two subfamilies of this family is deep and bowl-like on ental surface of the hypostomal arms. The mouthparts treated in here comprise the labrum, clypeus, mandibles, maxillae, labium, hypostoma and the septum of the preoral cavity. The terms are followed principally after Ting and Morimoto. The detail terminology fur the mandibles are newly given. [Insecta, Coleoptera, Comparative morphology, Mouthparts, Brentidae].

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.623-628
• /
• 2011

Micro EDM(Electric Discharge Machining) is one of the most powerful technologies which are capable of fabricating micro-structure without any problems from high cutting force. However, there is a significant defect in the part machining with deep holes or pockets, because debris which are generated by electric discharging may frequently cause a short circuit between an electrode and workpiece material. Vibration flushing can reduce the undesirable phenomena with dynamic flow of EDM fluid in a deep and choked area. In this study, Vibration flushing with solenoid is suggested and the results show that the method can generate a remarkable EDM efficiency with high amplitude at a low frequency in comparison with current vibration flushing methods with high frequency using piezo actuators.

• Korean Journal of Environmental Biology
• /
• v.37 no.2
• /
• pp.217-227
• /
• 2019

The purpose of this study was to investigate the initial growth, burrowing depth, and relative growth of mud shrimps (Upogebia major and Austinogebia wuhsienweni), living in damaged high density tidal flat shellfish farms form 2008 in the Western coast of Korea. By August, young mud shrimps (Upogebia major), which had settled down on the tidal flats in early May, grew to more than 10 mm in carapace length (CL). At the end of the first year, their CL and total length (TL) increased to 14.21 mm and 42.28 mm, respectively. The inhabiting depth of the young mud shrimps (Upogebia major) increased rapidly up to about 6 months after stocking (5 cm in July, 12.5 cm in September, and 28 cm in November, respectively). The inhabiting depth of adult mud shrimps in their burrows was about 10-93 cm during the year. As results, the analysis of the relative growth between the carapace length (CL) - the total length (TL) and the CL - total wet weight (TWW), the total wet weight of mud shrimps at Boryeong Saho (inner part of the Cheonsu-bay) was estimated to be 1.2-4 g heavier than those of Boryeong Jugyo (Outer part of the Cheonsu-bay) tidal flat. The young mud shrimps primarily grew from April to October. It is therefore crucial to observe whether the settlement of young mud shrimps on tidal shellfish farms from May to June to minimize the damage of shellfish farms by newly stocked young mud shrimps. In addition, it is recommended that young mud shrimps grown in fisheries be harvested before they dig deep into the sediment until early December.

• Journal of the Korean Society of Radiology
• /
• v.13 no.4
• /
• pp.661-666
• /
• 2019

Diverging collimators is used to obtain reduced images of an object, or to detect a wide filed-of-view (FOV) using a small gamma camera. In the gamma camera using the diverging collimators, the block scintillator, and the pixel scintillator array, gamma rays are obliquely incident on the scintillator surface when the source is located the periphery of the FOV. Therefore, the spatial resolution is reduced because it is obliquely detected in depth direction. In this study, we designed a novel system to improve the spatial resolution in the periphery of the FOV. Using a tapered crystal array to configure the scintillation pixels to coincide with the angle of the collimator's hole allows imaging to one scintillation pixel location, even if events occur to different depths. That is, even if is detected at various points in the diagonal direction, the gamma rays interact with one crystal pixel, so resolution does not degrade. The resolution of the block scintillator and the tapered crystal array was compared and evaluated through Geant4 Application for Tomographic Emission (GATE) simulation. The spatial resolution of the obtained image was 4.05 mm in the block scintillator and 2.97 mm in the tapered crystal array. There was a 26.67% spatial resolution improvement in the tapered crystal array compared to the block scintillation.