• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.22-27
• /
• 2010

본 논문은 유한체적법에 근거한 CFD 분석기법을 이용하여 증기 이젝터의 성능에 대하여 구동노즐의 기하학적 형상에 따른 영향을 조사하였다. 구동노즐의 직경비를 변화시키고 또한 직경비를 일정하게하고 구동 노즐의 위치를 변화시키면서 최적의 조건을 조사하였다. 연구 결과 이젝터의 성능은 구동노즐의 직경과 노즐의 출구 위치에 의해 좌우됨을 확인하였다. 일정 노즐 면적비에 대하여 노즐 목 직경이 감소함에 따라 혼입율이 증가하는 것을 확인하였고 일정 노즐 목 직경에 대하여 면적비의 증가는 혼입율의 감소의 원인이 된다는 것을 확인할 수 있었다. 또한 혼입율은 노즐의 출구 위치에 따라 영향을 받는다는 것도 확인하였다. 혼입율은 노즐 출구의 위치가 이젝터의 상류로 이동할수록 증가하고 그 위치는 이젝터의 일정단면적부 직경(D)에 대하여 0.4D일 때 최적의 성능을 보였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.8
• /
• pp.645-651
• /
• 2015

The objective of this study is to experimentally investigate the effect of design parameter on the mass ratio of a central-driven ejector. The design parameters are the primary nozzle area and distance ratios, diffuser exit-area ratio and mixing-tube length ratio. The experimental setup was an open-loop continuous circulation system which has a movable nozzle ejector, an electric motor-pump, a water tank, a control panel and high-speed camera unit. We calculated the mass ratio using the measured primary and suction-flow rates with the experimental parameter of primary water-flow rate or pressure. The results showed that the mass ratio increased with the primary nozzle distance ratio and mixing tube length ratio, while the mass ratio decreased with the primary nozzle-area ratio and diffuser exit-area ratio.

• Journal of ILASS-Korea
• /
• v.27 no.3
• /
• pp.126-133
• /
• 2022

The objective of this is to experimentally investigate the effect of mixed jet on the oxygen transfer characteristics with the primary nozzle area ratio of an annular nozzle ejector for the application of a microbial fuel cell. A direct visualization method with a high speed camera system was used to capture the horizontal mixed jet images, and a binarization technique was used to analyze the images. The clean water unsteady state technique was used for the oxygen transfer measurement. The air-water mixed jet discharging into a water tank behaved similar to a buoyancy or horizontal jet with the primary nozzle area ratio. It was found that an optimum primary nozzle area ratio was observed where the oxygen transfer performance reached its maximum value due to the decrease of air volume fraction and the increase of jet length and air bubble dispersion.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.68-75
• /
• 2015

In this paper, unsteady characteristics of pressure in solid rocket motor were analyzed by using response of pintle actuation, pressure and thrust data from ground test. Pressure and thrust in solid rocket motor can be controlled in real time by varying nozzle throat area with pintle, installed in the valve. Unsteady characteristics of pressure can be observed in this system occurred by various reasons. Two critical reasons, error of pintle actuation and ablation of center tube, are found and effects of each reason can be analyzed individually by re-prediction of pressure with response of pintle actuation and analyzing thrust to pressure ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.662-665
• /
• 2011

Pintle technology, which is one of the thrust control method for solid rocket motor, can control the thrust by the control of nozzle throat area through the pintle moving. For studying the unsteady flow characteristics of pintle nozzle by needle type pintle moving, cold flow test and numerical analysis were performed. The pressure distribution on the pintle tip was varied for pintle moving and stopping and thrust was varied by this effects.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.5
• /
• pp.61-70
• /
• 2017

Robust thrust distribution method of solid DACS is researched. For the case of the system which has higher number of actuation nozzles than the degree of freedom of thrust to be controlled, the robust thrust allocation law which accommodate the abnormal operation is suggested. Assuming the situation that some nozzles are uncontrollable, the error between nozzle throat area command and response can be calculated. The error is used for realtime reshaping of weighting matrix. From the weighting effect, the nozzle which operated abnormally has low responsibility for the command then, the thrust error is reduced. The suggested algorithm is verified by the simulation of abnormal operation condition of DCS and ACS nozzle respectively.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• v.10 no.2
• /
• pp.32-35
• /
• 2005

밭고랑 옆의 해가림시설 지주목에 파이프라인을 설치하고 방제장치를 탑재한 주행장치가 자동으로 파이프를 추적하면서 농약을 살포 할 수 있는 방제기를 개발하여 인삼재배포장에서 성능시험을 실시하였다. 그 결과를 요약하면다음과 같다. 가. 인삼재배용 방제기의 주행장치는 동력원으로 축전지를 사용하는 DC모터에 의한 4륜 구동형으로 제작하였고, 방제장치는 수직 붐노즐 방식으로 쌍선형 노즐을 좌우에 3개씩 부착하고 살포각도를 조절할 수 있도록 제작하였으며, 인력으로 골간 이동시키는 방식이다 나. 성능시험결과 주행속도는 0.3m/s이고, 장애물이나 요철부의 통과 가능높이는 4cm였고, 작업성능은 38분/10a로 나타났다. 다. 방제성능은 피복면적비를 측정한 결과 인삼 잎 앞면은 100%, 뒷면은 40%이상으로 분무입자의 부착률이 양호한 것으로 나타났다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.49-59
• /
• 2008

The effects of design parameters on the pellet transport rate in the ejector system which is widely used in the production processes of automotive parts were investigated experimentally. The primary nozzle geometry, the area ratio (R) of nozzle exit cross-sectional area to mixing chamber cross-sectional area and the distance (S) from primary nozzle exit to mixing chamber entrance were considered as the design parameters. The area ratios of the primary nozzle were varied from R=0.10 to R=0.25, 0.30, 0.40 and 0.55. The primary nozzle was positioned at the non-dimensional distance (S/D) of 1.30, 1.87, 2.44, 3.00 and 3.75, normalized using the mixing chamber diameter (D). The design parameters were determined to run with high efficiency by measuring the pellets transport rate. The geometry and the area ratio (R) of the primary nozzle had an effect on the pellet transport rate of the ejector system, and the area ratio of R=0.3 was carefully selected after taking the minimum fluidization velocity and transport rate of applied pellets into account. The higher pellet transport rate with the variation of the distance (S/D) was observed at S/D of 2.44.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.3
• /
• pp.520-527
• /
• 1988

Liquid ejectors are widely used as marine pumps, inducer stage for the boiler feed water pump, boiler recirculating pump, cooling water recirculating pump in boiling water type nuclear reactor and a deep well pump, because of their high working confidence and simplicity. Furthermore, it requires only a modest net positive suction head for cavitation-free operation and it can be installed in remote location from mechanical power source. It is not easy to presume the friction losses, because it is complicately affected by area ratio, flowrate ratio, nozzle spacing, throat length, shape of liquid ejector and so on. Therefore, the optimization of liquid ejector design is still dependent, to a large extent, on the experimental results and empirical procedures. On the design of the liquid ejector, the area ratio and the nondimensional throat length are the most important design factors among the mentioned above. In this experiment, the effects of the area ratio and the nondimensional throat length to ejector efficiency are carried out systematically by the combination of 4 kinds of motive nozzle and 2 kinds of throat length. In this paper, the present experimental results are compared with the calculated ones by the previous computer aided design program based on one dimensional flow equation. And also, an empirical equation for the working limit of liquid ejector is reported.