• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2011.06a
• /
• pp.66-67
• /
• 2011

항로를 횡단하여 건설되는 교량이 증가하고 해상교통의 증가에 비례하여 항로의 혼잡도가 증가하는 만큼 선박과 교량의 충돌우려가 커지고 있다. 선박과 교량의 충돌은 단순 접촉사고가 아닌 재난급 사고의 개연성이 크다. 직접 손괴를 일으키는 큰 충돌이 아니더라도 선박과 교각의 충격진동에 의하여 교량상판이 균형을 잃고 연쇄 붕괴하는 일이 종종 발생하여 많은 인명의 손실이 발생하고 있기 때문이다. 적정 교각 폭, 교각의 시인성 증진을 위한 표지와 등화의 설치 및 점등방법 등의 환경 여건 개선, 충돌방지공의 효과 검토, 교량 통과전 사전 점검사항, 교량 부근에서 선박의 조종성 유지방안, 예선의 효과 연구, 관제기법과 안전규정, 불가피한 충돌이나 접촉의 경우 손실 감소대책과 충돌방지공의 효과 등 다각적인 연구가 필요하다. 면피용 탁상이론을 배제하고 현장실무의 경험을 바탕으로 실효적인 방안을 제시하고자 한다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.6
• /
• pp.675-682
• /
• 2015

Current design codes such as AASHTO LRFD or Korean Highway Bridge Design Code recommend of using static force for designing bridge column against vehicle collisions. However, there was an accident that the bridge was collapsed shortly after vehicle impact on bridge pier in Nebraska(near Big Spring, 2003). It was found that the second largest cause of bridge collapse is collision after hydraulic causes. It can be thought that the possibility of truck-bridge collision are getting increasing as the size of truck increases and traffic condition are becoming improved. However, dynamic behavior under the impact loading seldom considered in bridge design procedure due to computational cost and time. In this study, in order to reduce the computational cost for dynamic impact analysis, model reduction method was developed. Obtained results of residual displacement were compared with the results of direct impact simulations.

• Journal of the Korea Concrete Institute
• /
• v.22 no.4
• /
• pp.535-546
• /
• 2010

Recently, the probability of collision accident between vehicles or vessels and infrastructures are increasing at alarming rate. Particularly, collision impact load can be detrimental to sub-structures such as piers and columns. The damaged pier from an impact load of a vehicle or a vessel can lead to member damages, which make the member more vulnerable to impact load due to other accidents which. In extreme case, may cause structural collapse. Therefore, in this study, the vehicle impact load on concrete compression member was considered to assess the quantitative design resistance capacity to improve, the existing design method and to setup the new damage assessment method. The case study was carried out using the LS-DYNA, an explicit finite element analysis program. The parameters for the case study were cross-section variation of pier, impact load angle, permanent axial load and axial load ratio, concrete strength, longitudinal and lateral rebar ratios, and slenderness ratio. Using the analysis results, the performance based resistance capacity evaluation method for impact load using satisfaction curve was developed using Bayesian probabilistic method, which can be applied to reinforced concrete column design for impact loads.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2019.11a
• /
• pp.81-83
• /
• 2019

해상교량 설치 시 교량표지는 선박과 교량구조물과의 충돌사고를 예방하는 중대한 역할을 수행한다. 이와 관련하여 현재 대부분 사설항로표지로 관리되고 있는 교량표지의 설치허가 협의 사례와 제도적 문제점을 공유하고 교량표지의 효율적인 관리를 위한 교각등, 경간 등과 같은 세부 설치규정을 제안하고자 한다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1111-1119
• /
• 2022

Tourism projects through islands in the waters of Sinan-gun became active, and as a result, a total of 13 marine bridges connecting islands were completed. However, the marine bridge constructed in the fairway is dangerous for traffic. Particularly, in the case of the marine bridge connecting two islands, the width of the fairway is extremely narrow, therefore the risk is higher. In this study, we evaluated the risk of collision between marine bridge piers and ships using the IALA Waterway Risk Assessment Program (IWRAP), a risk assessment model for port waterways, based on a maritime traffic survey on the coastal bridge in Sinan-gun. The results, indicated that No.1 Sinan bridge had the highest probability of collision and most of the transit ships were coastal passenger ships. In addition, No.1 Sinan bridge was the place where the most collision accidents occurred among the marine bridge piers in the target sea, and the cause this study was analyzed. An analysis of the satellite images of the sea environment of No.1 Sinan bridge using an image processing method, confirmed that obstacles that could not be seen in the chart existed nearby the bridge. As a result, traffic was observed to be concentrated in one direction, unlike two-way traffic, which is a method of inducing traffic of bridges to avoid obstacles. The risk cause analysis method using the image processing technique of this study is expected to be used as a basic research method for analyzing the risk factors of island bridge in the future.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.34 no.3
• /
• pp.137-149
• /
• 2021

Cable-stayed bridges are infrastructure facilities of a highly public nature; therefore, it is essential to ensure operational safety and prompt response in the event of a collapse or damage caused by natural and social disasters. Among social disasters, impact accidents can occur in bridges when a vehicle collides with a pier or when crashes occur due to aircraft defects. In the case of offshore bridges, ship collisions will occur at the bottom of the pylon. In this research, a procedure to evaluate the structural behavior of a cable-stayed bridge for aircraft impact is suggested based on a numerical analysis approach, and the feasibility of the procedure is demonstrated by performing an example assessment. The suggested procedure includes 1) setting up suitable aircraft impact hazard scenarios, 2) structural modeling considering the complex behavior mechanisms of cable-stayed bridges, and 3) structural behavior evaluation of cable-stayed bridges using numerical impact simulation. It was observed that the scenario set in this study did not significantly affect the target bridge. However, if impact analysis is performed through various scenarios in the future, the load position and critical load level to cause serious damage to the bridge could be identified. The scenario-based assessment process employed in this study is expected to facilitate the evaluation of bridge structures under aircraft impact in both existing bridges and future designs.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.17 no.2
• /
• pp.179-185
• /
• 2011

A marine collision accident occurred at the Jin-do water way. A barge loaded with heavy equipment of Power Generation Plant was being towed at its side by two tugs "A" and "B" from Byeg-pa harbour to the designated position to be used for power generation plant near Jin-do bridge. The Power Generation Plant was 40-meters high loaded atop the barge. When the "tugs and tow" were approaching the Jin-do the bridge, the two towing tugs lost maneuvering control of the barge and it went off-course, hit first the waterway embankment and finally struck the lower part of bridge's span and post musing the barge to capsize and sunk its cargo into the sea. The bridge also suffered damages where the top of the Plant struck At the time of the accident, there was a strong tidal current at the waterway. This paper calculates the safe towing force of barges with heavy loads when traversing in a strong tidal current situation in narrow waterway.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.4
• /
• pp.363-371
• /
• 1996

The Steering and Sailing Rules of International Regulations for Preventing Collisions at Sea now in use direct the best aid - action to avoid collision by the stand - on vessel. But these rules do not refer to the safety relative distance between two vessels when she should take such action. In this paper, the author analyzed the ship's collision avoiding actions from the viewpoint of ship motions and worked out mathematical formulas to calculate the relative distances necessary for taking action to avoid collision. Figuring out the values of maneuvering indices through experiments of 11 actual ships of small, medium, large and mammoth size, the author applied these values to the calculating formulas and calculated the minimum relative distances. The main results are as follows: 1. It was confIrmed that the stand - on vessel should keep the greatest relative distance for taking best aid - action to avoid collision when the cross angle of course was $90^{\circ}$ and near it(70-$90^{\circ}$ ). 2. When the cross angle of course was $90^{\circ}$ , the minimum relative distance of small vessel(GT: 160-650tons) was found to be more than about 6.8 times of her own length, and those of medium(GT : 2,300-3,500tons), large(GT : 22,OOO-62,OOOtons) and mammoth(GT : 91,000-139,000tons) vessels were found to be more than about 9.0 times, about 5.4 times and about 6.8 times of their own lengths. 3. It was confIrmed that collision danger was greater when crossing angle was obtuse than in an acute angle, therefore greater relative distance was to be kept by the stand - on vessel for taking best aid - action to avoid collision in the case of the obtuse angle. 4. In every vessels, in the case of $90^{\circ}$ cross angle of course the safety minimum relative distance was found to be more than about 9.0 times of their own lengths.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.14 no.2
• /
• pp.97-112
• /
• 1978

The rule 15, 16 and 17 of International Regulations for Preventing collisions at Sea direct actions to avoid collision when two power-driven vessels are crossing. But these rules do not present the safety minimum approaching distances outside which a give- way vessel deeps out of the way of a stand-on vessel. In this paper, the author analyzed the ship's collision avoiding actions from a viewpoint of ship kinematics as the method to calculate this distance. The author worked out mathematic formulas for calculating the safety minimum approaching distances outside which the give-way vessel takes the actions to avoid collisions in accordance with the cross angles of the crossing vessels' courses. Figuring out actually the values of maneuvering indices of the M. S. Koan Ack San (GT: 224tons), the training ship of the National Fisheries University of Busan and the M. S. Golden Clover (GT: 101, 235tons) of the Eastern Shipping Co., Ltd. through their Z test, the author applied these values to the calculating formulas and calculated the safety minimum approaching distances. The results of calculations are as follows; 1. The greatest distance is to be kept by the give-way vessel to avoid collision when the cross angle of courses is 90$^{\circ}$ or near it. In such case the safety minimum approaching distance of a small vessel must be more than 5 times of her own length and that of a large vessel more than 11 times of her own length. 2. Collision danger is greater when crossing angle is obtuse than in an acute angle, therefore greater distance is to be kept by the give-way vessel to avoid collision in the case of the obtuse angle. 3. The actions to be taken to avoid collisions by the give-way vessel in Rule 16 and by the stand-on vessel in Rule 17(a)(ii) of International Regulations for Preventing Collisions at Sea, must be done outside the above safety minimum approaching distance. When inevitably such actions are to be taken within the safety minimum approaching distance, they should be accompanied with engine motions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.6
• /
• pp.19-26
• /
• 2021

The seismic isolation system have been applied in order to protect the collapse of bridge by seismic load and the vertical load transmitted from the superstructure. However, the failure and damages of non-shrinkage mortar, isolator and wedge in total 12 bridge were reported by Pohang Earthquake. In this study, the damage mechanism and behavior characteristics of elastomeric bearing by an earthquake were evaluated to consider the seismic isolation system including non-shrinkage mortar and the seat concrete of pier. To discuss the effect of installed wedge and damage mode of elastomeric bearing, the compressive-shear tests were carried out. Also, the mechanical behaviors and damage mechanism for each component of elastomeric bearing were evaluated by using finite element analysis. From the test results, the cracks were created at boundary between non-shrinkage mortar and seismic isolator and the shear loads were rapidly increased after bump into wedge. The cause for damage mechanism of seismic isolation system was investigated by comparing stress distribution of anchor socket and non-shrinkage mortar depending on wedge during earthquake.