• Korean Journal of Optics and Photonics
• /
• v.17 no.1
• /
• pp.18-22
• /
• 2006

The transmission characteristics of multiply cascaded phase-shifted long-period fiber gratings(LPFGs) were investigated theo-retically and experimentally. Their passband can be changed by increasing the number of p-shifted LPFGs. When two p-shifted LPFGs with different grating lengths are cascaded in series, the bandwidth of the rejection band and passband can be controlled by the pristine characteristics of two gratings. We also investigate the transmission characteristics of phase-shifted LPFG by exposing the half of LPFG region to UV laser. The transmission characteristics strongly depend on the initial coupling strength of the LPFG.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1195-1200
• /
• 2007

Torque of a rotating shaft has been mostly measured by strain gages combined with either a slip ring or telemetry. However, these methods have severe inherent problems like low S/N ratio, high cost, limited number of channels and difficult installation. In this paper, a new method using FBG(fiber bragg grating) sensors and a rotary optical coupler for online non-contact torque monitoring is suggested. FBG sensor can measure both strain and temperature, and has much batter characteristics than those of a strain gage. A rotary optical coupler is a optical connecting device between a rotating shaft and stationary side without any physical contact. It has been devised for transmitting light between a rotating optical fiber and a stationary optical fiber. The proposed method uses this rotary optical coupler to connect FBG sensors on the rotating shaft to instruments at stationary side. And a reference FBG sensor is also applied to compensate the insertion loss change of the rotary optical coupler due to rotation. Three FBG sensors have been fabricated in a single optical fiber. Two FBG sensors are attached on the shaft surface to measure torque and one sensor is installed at the shaft center to compensate the insertion loss change. The torque of a rotating shaft has been successfully measured by the suggested method proving its superior performance potential.

• Polymer(Korea)
• /
• v.30 no.2
• /
• pp.158-161
• /
• 2006

Recently the application of plastic optical fiber (POF) in automotives and planes demands the heat-resistant and high refractive index con materials. We synthesized polyglutarimides (PGIs) via imidization of PMMA with primary amines under high pressure and high temperature and investigated thermal and optical properties by varying the molar ratio of amines and the type of amines (ethyl amine vs. isopropyl mine). The degree of imidization was calculated based on the peak intensity in $^1H$ NMR and FTIR. We found that the glass transition temperature $(T_g)$ of PGIs increased over $30^{\circ}C$ compared to the traditional core materials in POF, PMMA, and they are stable up to $300\sim400^{\circ}C$. PGIs anthesized with ethyl mine show the better heat resistance than those with isopropyl amines. Additionally, they show the comparable transparency and higher refractive index than PMMA. It implies that they can be utilized as the excellent photo-efficient and heat-resistant core materials in POF.

• Korean Journal of Optics and Photonics
• /
• v.10 no.2
• /
• pp.146-151
• /
• 1999

We demonstrated a harmonic mode locking scheme that used regeneratie phase modulation to get a high and stable repetition rate in a figure-of-eight fiber soliton laser. From the detected beat spectra of the laser output, a sinusoidal clock freguency tone of 400 MHz, the 96th harmonics of the fundamental mode locking frequency, was extracted with a high Q filter and was used to drive the phase modulator, resulting in stable output of soliton pulse train synchronized with the modulation signal. Generated soliton pulses had FWHM pulsewidth of 930 fs and 3.1 nm linewidth, yielding pulsewidth-bandwidth product of 0.359 that was close to the transform limit. As the modulation frequency always followed the beat frequency of laser modes, stable harmonic mode locking was achieved without the adjustment of the cavity length, which has been commonly required in actively mode-locked lasers.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.467-472
• /
• 2002

In this paper, we propose a polarization-insensitive temperature sensor using a thermo-optic effect of the upper and (or) lower cladding of a planar waveguide in contact with a side-polished fiber. A microscope cover glass with thickness of a 170 ${\mu}{\textrm}{m}$ is adopted as an overlay waveguide because this waveguide opposes sudden temperature change and ensures polarization-insensitive responses. The measured polarization-dependence loss is less than 0.3 dB. The temperature can be detected as a result of the shift in coupling wavelength of the sensor. We investigate the shift in coupling wavelength as a function of the temperature variation with respect to the different thermo-optic coefficients of lower and upper claddings. We also show that the temperature sensitivity of the device can be easily controlled by the thermo-optic coefficients of lower and upper claddings of the overlay waveguide.

• Korean Journal of Optics and Photonics
• /
• v.22 no.2
• /
• pp.96-101
• /
• 2011

Operational and thermal characteristics of a thin disk Yb:YAG crystal with a thickness of 0.8 mm were studied using as a pumping source a fiber-coupled 930 nm laser diode. The heat generated in the crystal was dissipated by placing both surfaces in contact with copper plates with central hole, and the dependence of the temperature change in the illuminated spot on hole size was investigated by measuring the spectral change of the lasing peaks. The slope efficiency and optical-to-optical efficiency with respect to the LD pump power were as high as 42.2% and 34.8%, respectively. The temperature at the illuminated spot increased with diode current and with increasing hole size of the copper plate. When the hole size considerably exceeded the crystal thickness, the temperature rise deviated from the linear increase at high pump power.

• Korean Journal of Optics and Photonics
• /
• v.6 no.4
• /
• pp.310-316
• /
• 1995

We designed the $1.3/1.55\mum$ WDM directional coupler and its coupling length was calculated with the variation of the two waveguide's core separation and other variables by the Fourier transformed scalar wave equation. We deposited the PSG films for optical waveguide by low pressure chemical vapor deposition and fabricated the WDM coupler using the laser lithography and $CF_4/O_2$ reactive ion etching process. A V -groove which was made to support and fix the optical fiber is fabricated on Si substrate by chemical etching. The WDM coupler and the V-groove are connected using UV curing epoxy. We found that propagation mode of each port of WDM coupler is single mode and maximum extinction ratio between two out ports is 6 dB for $1.3.\mum$, and 12 dB for $1.55\mum$. /TEX>.

• Korean Journal of Optics and Photonics
• /
• v.8 no.6
• /
• pp.476-481
• /
• 1997

Optimum operating conditions of the 0.98 $\mu\textrm{m}$-pumped broadband erbium-doped fiber sources, where the mean wavelength variation is minimized, have been experimentally investigated. The optimum conditions for the mean wavelength stabilization were found to be different between the case of the isolated source and the case of the presence of feedback. In case of feedback, the proper pump power that yields zero slope of mean wavelength variation was found to be lower than that of the isolated case, and the mean wavelength was found nearly unchanged over the wide range of pump power. Howerer, the feedback resulted in lower output power and the mean wavelength was found to be sensitive to the variation of feedback level. In the respect of mean wavelength stability, the better performance could be obtained with some feedback, provided that the feedback level is kept constant. Thus we could also enhance the mean wavelength stability by allowing appropriate constant feedback into the source.

• Korean Journal of Optics and Photonics
• /
• v.18 no.2
• /
• pp.162-166
• /
• 2007

In this paper, we propose a WDM optical true time-delay (OTTD) beam former for phased way antenna (PAA) systems. It is composed of a delay lines matrix and a multiwavelength source with discrete DFB laser diodes. The building block of a delay lines matrix is a $2\times2$ optical MEMS switch with proper fiber-optic delay line connected between cross ports. A $4\times3$ matrix using four DFB lasers has been fabricated with unit time-delay difference of 12 ps. Maximum time-delay error was measured to be -1.74 ps and +1.14 ps at a radiation angle of $46.05^{\circ}$, corresponding to error range of $-2.87^{\circ}\sim+1.88^{\circ}$. By measuring time-delays at six different RF frequencies from 5- to 10-GHz, we verified the true time-delay characteristic of our OTTD.

• Korean Journal of Optics and Photonics
• /
• v.18 no.2
• /
• pp.93-99
• /
• 2007

We investigated analytically and numerically the occurrence of modulation instability in fibers with periodic changes both in dispersion and gain. Previously, it has been known that the modulation instability is suppressed in dispersion managed solitons where dispersion is managed in such a way that the local dispersion alternates between the normal and the anomalous regimes. In this work, we enhanced the advantage of the dispersion management scheme by additionally introducing proper gain/loss profiles in fibers. The gain/loss profile is given by $\Gamma(z)=0.5/D(z)*(dD/dz)$, where D(z) represents the dispersion profile. The fundamental gain spectra of the modulation instability in the dispersion and gain managed fibers have been derived analytically and confirmed by numerical calculation. Our investigation reveals that in the dispersion and gain fibers the modulation instabilities are always much more suppressed compared to the case with only dispersion managed. In practical dispersion management schemes, dispersion profiles show discontinuity. and thus. the corresponding gain/loss profiles tend to be finite. In these cases, the gain/loss profiles were approximated by lumped gains/losses of finite values. Our numerical calculations confirm that this approximation also works well.