• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.3
• /
• pp.21-24
• /
• 1981

A simple optial fiber Y-branch is fabricated using micro - torch and fusion splicer. Tapered end of two fibers - in -contact is spliced with another fiber. Total insertion loss is 26dB and optical power branchi ng ratio is 0.98. Using fiber Y-branch, an UTDR with simple optical system is realized The resolution of the OTDR is $\pm$ 5m in length and t 0.5 dB/km in loss coefficient.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.1
• /
• pp.1-6
• /
• 1984

Calculation of the launch-condition dependent near field pattern, modal power distribution and far field pattern of the SGS mode scrambler by ray optical approch fits well with the experiment. These results were applied to explain how to establish the stable mode launching into the grated index multimode fiber under test by the SGS mode scrambler. The effective use of the 5G5 mode scrambler is found to restrict the launching NA as well as possible. This was also confirmed by experiment.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1597-1598
• /
• 2006

광간섭계는 물체의 기하학적 구조 및 의료영상계측등 다양한 분야의 광계측에서 매우 일반적으로 사용된다. 이러한 광간섭계에서 광지연단은 측정대상의 기준을 위해 사용되고, 광간섭계의 계측속도는 광지연단에 의해 제한된다. 본 논문에서는 고속 광 지연단을 위해 기존의 기계적 방식을 배제하고, 광학적 방식의 광 간섭계를 구성하였다. 고속 광간섭계의 구성은 1304nm의 10GHz광원을 이용하였으며, 광지연단으로 광위상변조기와 광섬유를 이용하여 안정적이고 고속의 광 간섭계를 구성하였다. 구성된 광간섭계는 광위상변조기의 변조전압, 변조주파수에 의해 광지연시간을 가변할 수 있으며, 10MHz 반복율에 대해 11ps의 광지연시간을 얻을 수 있었다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.223-226
• /
• 2003

본 연구에서는 패러데이 효과(Faraday Effect)를 이용한 초고압 전력설비에서의 광전류 센서의 특성에 대한 기초 연구를 하였다. 광원은 Laser Diode(1310[nm])를 사용하고, 수신부는 PIN-Photodiode를 사용하였다. 센싱부로 사용한 광섬유는 single mode unjacked fiber를 사용하였고, 편광기를 사용하여 빛의 광학적인 편파면을 이용한 전류측정이 가능함을 확인할 수 있었다. 측정 결과에서는 전류에 따른 출력 신호가 나옴으로써 기존 문헌상의 결과와 동일하다는 것을 알 수 있었고 센싱부로 사용한 파이버의 길이에 따른 출력차이를 통해 파이버의 길이가 길수록 강도가 커진다는 것을 알 수 있었다. 또한 길이에 따라 출력의 차이뿐만 아니라 선형성까지도 차이가 난다는 것을 알 수 있었다. reference 값과 광전류센서의 출력 강도와의 오차율을 구했을 때 5[m] 10[m]길이의 광섬유 각각에 대해서 1000[A]이상의 값에서 각각 약 -0.9[%], -0.4[%]의 오차율을 보임을 확인했다. 여기서 인가한 전류값과 길이 즉, 감은 수에 따라 그 오차율이 점점 나아질 수 있다는 것을 알 수 있었다.

• Korean Journal of Optics and Photonics
• /
• v.32 no.6
• /
• pp.276-285
• /
• 2021

This paper reports the study of the line-beam optical system of the laser lift-off (LLO) equipment used in the OLED manufacturing process. To obtain both a long process depth and a narrow width of the line beam, even with the poor M² value of the laser source, the research is focused on the optical system, including the beam transformation unit (BTU). We also propose optical configurations for the super-Gaussian distribution and the fiber-based BTU for the flat-top distribution.

• Korean Journal of Optics and Photonics
• /
• v.33 no.5
• /
• pp.210-217
• /
• 2022

In this paper, a study is conducted on the acceptable tolerance of an alignment device to reduce the optical loss caused by the alignment tolerance of a window hermetic optical connector. To increase the transmission distance of optical signals and fiber-optic communication systems, it is necessary to maintain and improve the high optical efficiency of the connectors used to bond optical fibers. In the case of the window hermetic optical connector, the optical system is aligned through an alignment device. At this time, since the two connectors are used together, each component is fixed, and further alignment is impossible. The alignment tolerance of the housing system and pin used to align the optical system of the connector causes optical loss, leading to serious problems in the fiber-optic communication system. Thus, to find the acceptable tolerance required for manufacturing the optical-connector alignment device, tolerance analysis is performed on the components of the optical connector, such as the ball lens and the window. We also implement single-mode and multimode optical-connector systems, respectively. Based on the results, we determine an acceptable tolerance value for the alignment device.

• Korean Journal of Optics and Photonics
• /
• v.35 no.4
• /
• pp.157-163
• /
• 2024

We developed a 3-channel fiber laser with a common seed and a phase control system for laser beam combining through a diffractive optical element. Beam combining was performed by adjusting the angles of the beams incident on the diffractive optical elements, and the phase of each beam was controlled to maximize the intensity of the combined laser beam. The power of the 3-channel laser before passing through the diffractive optical elements is about 65 mW. The power of the combined beam varied between 2.9 mW and 48.3 mW depending on the phase change of each channel. Through phase control, the output of the combined beam can be maintained at 42 mW for more than 91.8% of the total time. It is expected that higher combining efficiency can be achieved by improving the transmittance of the diffractive optical elements and the performance of the phase control system.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1405-1406
• /
• 2015

본 논문에서는 비교적 가격이 저렴하면서 전자기장의 영향을 적게 받는 광학 소자를 이용하여 각도를 측정하는 연구에 대해 다루고 있다. 보다 측정 범위를 넓히기 위해 빛을 수광하는 포토트랜지스터를 3개 사용하였고, 발광부의 빛을 효과적으로 전달하기 위해 광섬유를 사용하였으며, 이 광섬유의 끝을 여러 각도로 가공하였다. 그 결과 포토트랜지스터를 1개 사용한 경우보다 측정 범위가 넓어지고, 광섬유의 끝을 가공함으로써 측정 신호의 비대칭성과 피크점이 이동하는 것을 확인하였다. 본 연구는 각도 측정을 요하는 다양한 분야에서 활용될 수 있는 측정 기술에 기반이 될 것으로 판단된다.

• New Physics: Sae Mulli
• /
• v.68 no.12
• /
• pp.1374-1377
• /
• 2018

We achieved 95% visibility in the Hong-Ou-Mandel interference experiment while we achieved only 56% visibility in a previous report. We used a 120 mW 405 nm single-mode continuous wave laser, a 5-mm-thick type-1 ${\beta}$-barium borate single crystal, standard Hong-Ou-Mandel interferometer optics, two avalanche photodiode single-photon counters, and a homemade coincidence counting unit. The photon collection unit was the key difference between the present study and the previous study. In the present experiment, we used single-mode optical fibers for photon collection, which suppressed accidental coincidence between-different mode photons by acting as a spatial filter because of its core size being much smaller than a multi-mode fiber.

• Journal of Advanced Navigation Technology
• /
• v.26 no.5
• /
• pp.331-337
• /
• 2022

The length of optical fiber in dispersion-managed link combined with optical phase conjugation to compensate for signal distortion caused by chromatic dispersion and nonlinear Kerr effect is a major factor determining the compensation effectiveness. The dispersion-managed link consists of several fiber spans in which standard single mode fiber and dispersion compensating fiber are arranged. In this paper, the compensation effect in the link that changes residual dispersion per span only by adjusting the length of one type of optical fiber, which is different in the first half link and the second half link with respect to optical phase conjugator (OPC), has been investigated. It was confirmed that the best compensation for 960 Gb/s wavelength division multiplexed signal could be obtained in the dispersion-managed link, in which the cumulative dispersion profile is symmetric around the OPC, and the cumulative dispersion amount is all positive in the first half, and all the cumulative dispersion amount is distributed negatively in the second half.