• Korean Journal of Optics and Photonics
• /
• v.18 no.3
• /
• pp.208-215
• /
• 2007

A fiber-coupled laser-diode pumped ceramic Nd:YAG laser for compensating the thermal tensing effect was developed. The thermal tensing effect was compensated using a convex lens, which was 25 mm away from the laser rod, with a focal length of 30 mm and an effective clear aperture of 22 mm. Without a compensator, the laser output power decreased suddenly above a pump power of 6 W. Using a compensator, the laser output power increased linearly according to the pump power. The beam propagation factor $M^{2}$ was 2.4 under a pump power of 12 W.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.396-400
• /
• 2006

We present a weather-insensitive optical free-space communication method supporting optical packet channels. It operates optical fiber amplifiers in gain-saturation regions. When the propagation loss gets too high, it decreases the average packet rate, or the average packet length, or both, to increase the optical power level launched into the free-space. As a demonstration, we transmit $8{\times}10$ Gigabit Ethernet channels over a terrestrial distance of 2.4 km. One gain-saturated free-space optical repeater is used at the halfway point.

• Korean Journal of Optics and Photonics
• /
• v.12 no.5
• /
• pp.371-375
• /
• 2001

We have implemented a sensor head which consists of erbium doped fiber pumped by 1480 nm LD and single fiber Bragg grating for simultaneous measurement of strain and temperature. The measurement precision and speed are improved by using Mach-Zehnder interferometer instead of optical spectrum analyzer (OSA) as a demodulator. The measurement precision of temperature measured by the amplitude variation of output signal is 0.05$^{\circ}C$ and that of strain measured by the phase variation of output signal is 0.1$\mu$strain. The measurement precision of temperature and strain are improved nearly 140 times and 700 times, respectively, compared to those using an OSA with wavelength resolution of 0.97 nm as d demodulator.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.320-326
• /
• 1997

Broadband sources for fiber-optic gyroscope were constructed using erbium-doped fibers. Output power, linewidth, and mean wavelength were compared between four different source configurations. Among them, double pass configuration exhibited the highest output power, as high as 5.5 mW with 25 mW pumping at 1.48 ${\mu}{\textrm}{m}$ wavelength. It also showed nearly zero sensitivity of mean wavelength for the variation of pump power when a sufficient pumping was provided. Amplifier/Source configuration resulted in the highest detected power(power received by the gyro detector) that is more than 100 times larger than those of the other configurations, though it was the lowest of source output power. As the feedback level increased, the source power decreased while the linewidth increased, and mean wavelength varied significantly which would affect the scale factor of the gyroscope.

• Korean Journal of Optics and Photonics
• /
• v.8 no.4
• /
• pp.333-339
• /
• 1997

We fabricated a sensor head which consists of spliced different-diameter fiber gratings for discrimination between strain and temperature. Because the fibers were drawn from the same preform, their temperature characteristics were the same but not for strain sensitivities which are inversely proportional to fibers cross-sectional areas. In measurement range of 0-1500$\mu$strain and 20-10$0^{\circ}C$, we could obtain, by using the matrix calculation, the unknown physical quantities within 10% of calculation error compared with the micrometer and thermocouple values. To improve the strain measurement accuracy, we suggest a new, novel method which deploys an unbalanced fiber Mach-Zehnder interferometer. This new signal processing technique converts the strain information to interference signal amplitude variation, temperature-independently. we obtained measurement accuracy nearly 80 times better than that obtainable with the conventional optical spectrum analyzer usage.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.17-21
• /
• 2004

We demonstrate an S/S＋band discretely tunable thulium doped fiber laser (TTDFL), anchored on a 50-㎓ ITU-T grid. Investigating the inversion analysis of the thulium doped fiber (TDF) in applying a dual wavelength (1.4 m and 1.5 m) pumping scheme, a laser whose tuning range covers most of the S/S＋band has been obtained. Within the wide 3-㏈ bandwidth of 65.1 nm, the output power of the tunable laser exceeds 6.1 ㏈m with very flat spectral profile and the number of DWDM channels generated is as large as 178. If we increase the subsidiary pump power to 22 ㎽, the bandwidth is expanded up to 66.2 nm. By controlling the temperature of the fine grid filter, we have also shown that the frequency locking capability of the laser can be improved. The laser developed in this work is expected to be utilized as a practical optical source providing reference wavelengths in the S/S＋band.

• Korean Journal of Optics and Photonics
• /
• v.18 no.5
• /
• pp.345-350
• /
• 2007

The characteristics of the supercontinuum generated in photonic crystal fibers were investigated by using the generalized nonlinear $Schr\"{o}dinger$ equation and the split-step Fourier method. Based on the simulated results, we generated the supercontinuum spectrum with the flatness of ${\pm}4dB$ in the wavelength range of 650 to 900 nm by employing a 200-fs pulse of Ti:sapphire laser and a commercial photonic crystal fiber.

• Korean Journal of Optics and Photonics
• /
• v.21 no.6
• /
• pp.254-258
• /
• 2010

We investigate an optical technique for beam shaping and optical amplification of a pulsed laser diode without variation of its original properties, such as repetition rate and pulse duration. The horizontal and longitudinal sizes of the pulsed laser diode are 300 and $2{\mu}m$, respectively, and its output power is $1.1mW/cm^2$. The multimodal and elliptical pulse shape of the laser diode is converted to the single-modal and Gaussian pulse shape by using a lensed optical fiber. Since the single-modal lensed fiber coupling from the multimodal pulsed laser diode degrades the output power severely, the output power of the pulsed laser diode is dramatically enhanced by using an optical amplification method based on master oscillated power amplification (MOPA). The pulse qualities of the laser diode are not changed after amplifying the pulse power and the output power was finally measured to be $29mW/cm^2$.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.461-466
• /
• 2002

Fiber-optic comb filters using a side-polished fiber coupler are proposed as multi-channel isolation filters on wavelength division multiplexing systems. We have demonstrated that the coupling efficiency between two waveguides is improved by the intermediate coupling layer in spite of the decrease of the optical power transfer between two waveguides due to the high-order modes of the overlay waveguide coupled with the side-polished single-mode fiber. When LiNbO$_3$with a 200-${\mu}{\textrm}{m}$-thickness was applied as a planar-overlay-waveguide, the comb filtering characteristics with a 4 nm-channel-spacing were achieved and the maximum power coupling occurred at the 1-${\mu}{\textrm}{m}$-thickness and the refractive index in range 1.52 to 1.53 of an intermediate coupling layer. If the intermediate coupling layer is optimized, an extinction ratio with more than 20 dB can be obtained. These experimental results are in good agreement with the BPM simulation.

• Korean Journal of Optics and Photonics
• /
• v.15 no.5
• /
• pp.415-422
• /
• 2004

We propose and present a new multiplexed bend loss type single-mode fiber-optic sensor system for displacement measurement in order to measure the displacement of several mm of civil engineering structures such as bridges and buildings. We make a bend loss type fiber-optic sensor for measuring displacements using the signal difference between two reflection signals due to various bend losses generating at a pair of optical connectors by using the optical time domain reflectometer. And we fabricate a multiplexed bend loss type fiber-optic sensor detecting linear displacements of 4 measuring positions of an object by setting these new 4 fiber-optic sensors on a single mode fiber simultaneously. We find that the multiplexed fiber-optics displacement sensor has linearity of 0.9942, maximum displacement of 6 mm, and accuracy of 6% for 4 measuring points.