• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.4
• /
• pp.894-900
• /
• 2004

There are many types of circularly polarized(CP) microstrip antenna elements, which are used as a good unit radiator. Since an advantage of CP antenna is no strict alignment requirements between Rx and Tx system, the printed antennas with circular polarization are very often used in numerous satellite and mobile radio systems. In order to realize the broad bandwidth of 3 dB axial ratio and impedance of CP microstrip antenna, complex feed structure and tri-plate patch element have been researched. This paper describes a design of wideband microstrip cross slot array antennas with circular polarization. The proposed antenna is composed of an open-ended microstrip feed line as a feeder and a cross slot as a radiator for circular polarization. To realize the wide bandwidth, tri-plate structure are considered and cross slot is electromagnetically coupled with feed line. Optimum parameters of 1-element cross slot antenna are analyzed and designed by method of moments. These parameters are also applied to may antennas design considered the mutual coupling between radiating elements. Right hand circular polarization(RHCP) and left hand circular polarization(LHCP) of the proposed antenna are easily controlled by asymmetrical cross slot structure and slot position. In 1-element and 15-element cross slot array antenna, the good axial ratio of 1 dB below and the broad bandwidth characteristics of antenna are obtained.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.727-737
• /
• 1999

Printed microstrip antennas are known to have limitations in terms of bandwidth and efficiency all imposed by the presence of the dielectric substrate. In this paper, to overcome these limitations, rather than using a superstrate geometry, the printed circuit is etched out of metal and supported in "strategic points" by(metallic or nonmetallic) post. The main motivation for this work was to obtain the wide bandwidth microstrip antennal which exhibits a higher efficiency than conventional ones. In this paper, to increase the bandwidth, patch sizes, electrical thickness and impedance matching are considered.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.1
• /
• pp.13-19
• /
• 2004

This paper demonstrates the detailed study of a microstrip Yagi-Uda antenna with and without PBG structure at wireless LAN(5725∼5825 MHz) frequency band. The impedance bandwidth of the antenna with the PBG holes is greater than (about 30 MHz) that of its counter part without PBG holes. The measured gains of the antenna at the frequency band are 7 dB and 6 dB respectively for antenna with and without PBG. The improvement of gain of about 1 dB is likely due to the suppression of surface wave.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.3
• /
• pp.15-20
• /
• 2004

In this paper, a wideband two-layer H-shaped microstrip antenna for WLAN is designed. To increase the bandwidth of microstrip patch antenna a configuration of stacked type using parastic element is used. Furthermore, to reduce the size of microstrip patch antenna, two techniques are employed . the first one is H-shaped patch type and the second one is that the main radiator and parastic patch are shorted to the ground plane using ten shorting posts. The antenna bandwidth and radiation characteristics are calculated by ENSEMBLE ver. 5.0 simulation software, and compared with the experimental results. Experiment results show that the bandwidth of antenna in 740MHz centered at 5.46㎓(13.5%), which is close agreement with the calculations, 770MHz(13%). Also, the antenna size can be reduced by 71.5% compared with the half wavelength rectangular microstrip antenna using the same substrate at the same frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.4
• /
• pp.473-482
• /
• 1998

In this paper, characteristics of the wide band microstrip antennas with parasistic element are analyzed by the Finite Difference Time Domain(FDTD) method, and antenna parameters are optimized to get maximum bandwidth, retern loss, input impedance, and radiation pattern are calculated by Founier transforming the time domain results. The characteristics of the antenna are varied and the bandwidth of the antenna is broaded as a length and a width of the driven element, a gap of the driven element and the parasitic element, a width and a length of parasitic element. So the different patchs are resonating at different frequencies and this multipule resonance increase the bandwidth. The Results of the calculation and measurement, the size of the antenna with parasitic element is about a twice larger than a microstrip antenna, but bandwidth is four times better than a microstrip antenna. And these results were in relatively good accordance with the measured values.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.11
• /
• pp.1774-1784
• /
• 1993

This paper presents the design, fabrication and measured results of the broadband microstrip array with a conical radiation pattern and the circular array composed of six square microstrip antenna elements. Each element antenna has the stacked structure with a parasitic element to achieve a broadband characteristic and a branch line quadrature hybrid is attached to it for the circular polarization. The design procedures and measured results of the scheme for obtaining the conical radiation pattern which is useful for the mobile communication via the satellite. Finally, the performance of the fabricated antenna is measured and compared with the theory.

• Journal of the Korea Society of Computer and Information
• /
• v.19 no.10
• /
• pp.71-79
• /
• 2014

In this paper, the microstrip array antenna is studied to replace the parabolic antenna in the direct satellite reception. A microstrip array antenna has been used in extremely limited area, but if it is applied to practical life like a direct satellite reception antenna, we expect that it will be used in various way. First of all, if we use a microstrip array antenna for a direct satellite reception antenna, it should be guaranteed characteristics of broadband frequency. Therefore, the goal of this paper is designing technique an antenna which guarantees broadband frequency band for a direct satellite reception. In this paper, the proposed microstrip antenna is fed by orthogonal two feed lines to a rectangular patch and a sequentially rotated feeding technique is designed proposed for a good axial ratio in broadband frequency band. The rectangular patch is designed to satellite reception band, and the width and length are W=L=8.9 mm ($0.352{\lambda}o$) respectively. The antenna's ground plane has dimensions of $250{\times}250mm$. The experimental results verify that the proposed antenna had the axial ratio of above 1dB broader than that of the conventional feeding antenna. In order to verify the performance, a $8{\times}8$ array having two pairs was fabricated and tested. The maximum gain is 20.8 dB, the sidelobe level confirm less than -10 dB. It is verified by link budget calculation that C/N=6.7 dB can be obtained for domestic use if this proposed antenna is used in Koreasat reception system.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.468-472
• /
• 2003

본 논문에서는 WLAN용 광대역 마이크로스트립 안테나를 설계 및 제작하였다. 광대역 특성을 얻기 위하여 기생 패치를 이용한 이중 공진 구조를 적용하였으며, 안테나의 사이즈를 줄이기 위하여 단락면을 사용하였다. 제작결과 return loss가 -10dB 이하인 대역폭으로 $4.41{\sim}6.15GHz$에 이르는 약 32.78%대의 광대역 특성을 얻을 수 있었다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.6
• /
• pp.1045-1052
• /
• 2019

In this paper, the slot-coupled microstrip antenna structure with reflector is used for broadband. The reflector of this structure is designed to reduce the radiation emitted from the slot and minimize the influence of external electromagnetic environment while reducing the overall antenna height. Experimental results show that the antenna is very well matched with VSWR below 1.4 at 1.942.17GHz, and the maximum gain of the antenna in this band was measured 9.21dBi. The measured results shows that it can be used in the wireless communication field or IoT field of other frequency band in the future.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.1
• /
• pp.11-17
• /
• 2004

In this paper, A miniature broad-band dime antenna is designed. This antenna consists of two stacked circular patches that create two cylindrical slots resonating at two slightly different frequencies, fed by a strategically positioned coaxial prove. To increase the bandwidth of microstrip patch antenna, a configuration of stacked type is used. Furthermore, to reduce the size of microstrip patch antenna and obtain a double resonant behavior, two shorting-walls are used. Experimental results show that the antenna bandwidth is about 26% centered at 5.8㎓ and are close agreement with the calculation results by HFSS 7.0 software.