• Journal of the Korean Solar Energy Society
• /
• v.28 no.2
• /
• pp.64-69
• /
• 2008

As the grid-connected photovoltaic power conditioning systems (PVPCS) are installed in many residential areas, these have raised potential problems of network protection on electrical power system. One of the numerous problems is an Islanding phenomenon. There has been an argument that it may be a non-issue in practice because the probability of islanding is extremely low. However, there are three counter-arguments: First, the low probability of islanding is based on the assumption of 100% power matching between the PVPCS and the islanded local loads. In fact, an islanding can be easily formed even without 100% power matching (the power mismatch could be up to 30% if only traditional protections are used, e.g. under/over voltage/frequency). The 30% power-mismatch condition will drastically increase the islanding probability. Second, even with a larger power mismatch, the time for voltage or frequency to deviate sufficiently to cause a trip, plus the time required to execute a trip (particularly if conventional switchgear is required to operate), can easily be greater than the typical re-close time on the distribution circuit. Third, the low-probability argument is based on the study of PVPCS. Especially, if the output power of PVPCS equals to power consumption of local loads, it is very difficult for the PVPCS to sustain the voltage and frequency in an islanding. Unintentional islanding of PVPCS may result in power-quality issues, interference to grid-protection devices, equipment damage, and even personnel safety hazards. Therefore the verification of anti-islanding performance is strongly needed. In this paper, improved RPV method is proposed through considering power quality and anti-islanding capacity of grid-connected single-phase PVPCS in IEEE Std 1547 ("Standard for Interconnecting Distributed Resources to Electric Power Systems"). And the simulation results are verified.

• Analytical Science and Technology
• /
• v.19 no.4
• /
• pp.342-351
• /
• 2006

This study was carried out to estimate the contents of heavy metals in big marine 17 kinds of fishes (n=89) which had been sold at wholesale market in Seoul from January to December in 2005. The contents of mercury (Hg), lead (Pb), cadmium (Cd), chrome (Cr), copper (Cu) and arsenic (As) were measured by the mercury analyzer and atomic spectrophotometer (AAS) in the flesh, liver, and gill part. The values of heavy metals in fishes were as follows ($Mean{\pm}SD$, mg/kg). The average contents of heavy metals in the fishes were Hg $0.08{\pm}0.01mg/kg$, Pb $0.17{\pm}0.32mg/kg$, Cd $0.34{\pm}0.07mg/kg$, Cr $0.05{\pm}0.05mg/kg$, Cu $1.14{\pm}0.13mg/kg$, As $0.24{\pm}0.22mg/kg$. Of the heavy metals detected in 3 parts, liver was measured highly in the all heavy metals. Of the heavy metals detected in countries, Hg, Pb, and Cu were measured highly in New Zealand, Cd and As in Norway, Cr in Korea. The range of heavy metal contents in imported and domestic fishes are low level, except of mercury contents of imported Yellow porgy (n=2), compared with regulation value of anther nations and Korea. And the contents of heavy metal in the imported fishes are natural. By correlation coefficients between fish livers of all subjects, a significant correlation was found Hg (r=0.989, p<0.01), Pb (r=0.978, p<0.01), Cd (r=0.991, p<0.01), Cu (r=0.998, p<0.01), As (r=0.198, p<0.05) in fish livers and flesh.

• Journal of IKEEE
• /
• v.28 no.1
• /
• pp.90-96
• /
• 2024

In this paper, we propose an automated system. It utilizes a Raspberry Pi camera and a function generator to analyze luminance in an image. Then, it applies voltage based on this analysis to control light transmission through coloring smart windows. The existing luminance meters used to measure luminance are expensive and require unnecessary movement from the user, making them difficult to use in real life. However, after taking a photography, luminance analysis in the image using the Python Open Source Computer Vision Library (OpenCV) is inexpensive and portable, so it can be easily applied in real life. This system was used in an environment where smart windows were applied to detect the luminance of windows. Based on the brightness of the image, the coloring of the smart window is adjusted to reduce the brightness of the window, allowing occupants to create a comfortable viewing environment.

• Progress in Medical Physics
• /
• v.26 no.4
• /
• pp.215-222
• /
• 2015

In this work, we performed a proof-of-concept experiment for phase-contrast x-ray imaging (PCXI) based on a single antiscatter grid and a polychromatic x-ray source. We established a table-top setup which consists of a focused-linear grid having a strip density of 200 lines/inch, a microfocus x-ray tube having a focal-spot size of about $5{\mu}m$, and a CMOS-type flat-panel detector having a pixel size of $48{\mu}m$. By using our prototype PCXI system and the Fourier demodulation technique, we successfully obtained attenuation, scattering, and differential phase-contrast images of improved visibility from the raw images of several selected samples at x-ray tube conditions of $90kV_p$ and 0.1 mAs. Further, fusion image (e.g., the attenuation+the scattering) may have an advantage in displaying details of the sample's structures that are not clearly visible in the conventional attenuation image. Our experimental results indicate that single-grid-based approach seems a useful method for PCXI with great simplicity and minimal requirements on the setup alignment.

• Journal of Animal Environmental Science
• /
• v.16 no.2
• /
• pp.143-152
• /
• 2010

Conditions for artificial culture of Lemna Paucicostata and its nutritional values were examined in this study. Lemna P. was cultured using artificial wastewater and a bioreactor (total volume $2,630\;cm^3$, working volume $2,240\;cm^3$) was operated at conditions of 6,250 lux and $28^{\circ}C$. Water flow affected the growth of Lemna P.: growth rate was very high (more than $1.1\;d^{-1}$) at a condition of no-water movement, but it was very low (less than $0.15\;d^{-1}$) when water moved slowly. The growth of Lemna P. was higher in $16h\;d^{-1}$ light cycle than in Sand $24h\;d^{-1}$, and it was also severely affected by the initial $NH_4$-N levels of wastewater. The growth rate of Lemna P. was high in lower $NH_4$-N level, indicating that the growth rate is in inverse proportion to $NH_4$-N concentration in wastewater. However, the contents of crude protein (CP) of Lemna P. were proportional to the initial $NH_4$-N concentration. The CP contents of Lemna P. cultured at 2, 10, 50 and 100 $NH_4$-N mg $L^{-1}$ was 18, 24, 37, 43%, respectively, showing the Lemna P. cultured at 50 and $100\;mg\;L^{-1}$ had similar protein contents to linseed (CP 35%), cottonseed (CP 38%) and soybean (CP 45%). Fat, protein, fiber, NDF and ADF contents of Lemna P. harvested at conditions of $16h\;d^{-1}$ light cycle and less than $2\;mg\;L^{-1}$ of $NH_4$-N level was 2.8, 18, 27, 20, 41 and 65.7%, respectively. Since the growth rate of Lemna P. was very high (more than $1.1\;d^{-1}$) at those conditions, it was convinced that mass production of valuable protein and fiber sources are feasible. In particular, since the Lemna P. has unsaturated fatty acids found mainly in animal fat as well as beneficial fatty acids to health such as C18:ln9c, C18:2n6c, C20:5n3 and C22:2, the Lemna P. biomass would be a highly valuable alternative feed source to grains.

• The Korean Journal of Food And Nutrition
• /
• v.18 no.3
• /
• pp.207-218
• /
• 2005

In room temperature, Kimchi becomes acidified and a little decayed, scenting a bad smell, and It couldn't be well kept. But if it should be made into a pill, it could be preserved for a long time for marketing, with nutrition highly concentrated as well as with no scent. Therefore, making Kimchi into a pill needs drying. When dried Kimchi, lactic acid and fragrant ingredient will vanish along with volatilization. The cyclodextrin(CD) as a stabilizer shows that the protecting rate of volatility of lactic acid in Kimchi is higher before than that of after fermentation, and it is higher at the addition $2\%\;than\;of\;1\%$ in case of Kimchi with CD. But it doesn't give much effect on total sugar, reducing sugar, protein and amino acid. Evaporation rate of lactic acid is the least in freeze dry, and natural dry, heat dry come next, respectively. In heat dry, if dried at more than $60^{\circ}C$ for a long time, Kimchi exudes boiling and scorched scent, causing bitter taste. The result of HPLC with superose 12 column at 280nm and 210nm shows that place and amount of main peak is almost the same, but the distribution of other peaks are different, with the revelation of various peaks like peptide and amino acid. The Kimchi pill made by the addition of $1\%$ CD shows that concentration is eight times higher than general Kimchi, total sugar is $14.4\%$, reducing sugar is $8.8\%$, protein is $4.8\%$, amino acid is $2.4\%$, and other contents are $74.4\%$, acidity is 32.8, and pH is 3.5 each. The result of letting 20 people with obesity, 20 patients with constipation have 30 pills(total weight 30g) three times a day for 60 days reveals they lost $2.29\%$ in weight on the average, and 7 among 20 were all relieved in constipation, and 8 responded that they experienced its efficacy.

• Korean Journal of Optics and Photonics
• /
• v.27 no.1
• /
• pp.18-24
• /
• 2016

To effectively utilize a flash and predict its effects on an infrared device, it is essential to know the infrared characteristics of the flash source. In this paper, a study of the IR characteristics of flash light sources is carried out. The IR characteristics of three flash sources, of which two are combustive and the other is explosive, are measured with an IR characteristic measurement system over the middle- and long-wavelength infrared ranges. From the measurements, the radiances over the two IR ranges and the radiative temperatures of the flashes are extracted. The IR radiance of flash A is found to be the strongest among the three, followed by those of sources C and B. It is also shown that the IR radiance of flash A is about 10 times stronger than that of flash B, even though these two sources are the same type of flash with the same powder. This means that the IR radiance intensity of a combustive flash source depends only on the amount of powder, not on the characteristics of the powder. From the measured radiance over MWIR and LWIR ranges for each flashes, the radiative temperatures of the flashes are extracted by fitting the measured data to blackbody radiance. The best-fit radiative temperatures (equivalent to black-body temperatures) of the three flash sources A, B, and C are 3300, 1120, and 1640 K respectively. From the radiance measurements and radiative temperatures of the three flash sources, it is shown that a combustive source radiates more IR energy than an explosive one; this mean, in turn, that the effects of a combustive flash on an IR device are more profound than those of an explosive flash source. The measured IR radiances and radiative temperatures of the flash sources in this study can be used to estimate the effects of flashes on various IR devices, and play a critical role for the modeling and simulation of the effects of a flash source on various IR devices.

• Journal of Mushroom
• /
• v.3 no.4
• /
• pp.133-139
• /
• 2005

Fruiting bodies of Cordyceps have been regarded as popular folk and effective medicines to treat human diseases such as asthma, bronchial and lung inflammation, and kidney disease. Cordyceps pruinosa (Clavicipitaceae; Hypocreales; Ascomycotina) has received special attention for medicinal purpose due to its various physiological activites. The nucleoside derivative N6-(2-hydroxyethyl) adenosine (HEA) isolated from it showed a $Ca^{2+}$ antagonistic effect and negative inotropic response. The artificial production of fruiting body of C. pruinosa has not been tried successfully yet by using living silkworm substrate. To develop techniques for the production of C. pruinosa stromata on a large scale, the infection of Bombyx mori with C. pruinosa and the growth characteristics of stroma of C. pruinosa were investigated. Also, studied about biological activities of fruiting body formed on silkworm. Infection rate of the silkworm pupae with C. pruinosa was the highest in injection inoculation. The formation of the fruiting body of C. pruinosa was quite good in the room controlled at $21{\sim}25^{\circ}C$, over 91% of relative humidity and over 1500 lx. Glucose concentration was high in the fruiting bodies of the silkworm pupae infected with C. pruinosa on a dry weight basis. The most abundant amino acid in the fruiting bodies was arginine and phenylalanine. The fruiting bodies of silkworm pupae infected with C. pruinosa was rich in oleic acid. The high amount of citric acid was found in the fruiting bodies of silkworm pupae infected with C. pruinosa.

• Analytical Science and Technology
• /
• v.22 no.4
• /
• pp.336-344
• /
• 2009

This survey was carried out to estimate the contents of heavy metals (Hg, Pb, Cd, and As) in 10 kinds of dried marine products (n=189) which are closely related to food resources. The contents of heavy metals were estimated by inductively coupled plasma spectrometer (ICP) and mercury analyzer. The values of heavy metals in dried marine products were as follows (Mean${\pm}$SD (range), mg/kg). The average contents of heavy metals in the dried marine products were Hg $0.058{\pm}0.069$ (0.002~0.502) mg/kg, Pb $0.178{\pm}0.598$ (ND~5.130) mg/kg, Cd $0.306{\pm}0.610$ (ND~6.802) mg/kg, As $5.282{\pm}6.158$ (ND~71.760) mg/kg. The range of heavy metal contents in dried marine products are low level, except of lead contents (n=2). In the comparison of heavy metal content by anchovy size, it was shown that cadmium, mercury and arsenic were meaningfully different. The contents of heavy metals by the shape of shrimp and Alaska Pollack were shown that the result of each group was meaningless. In the comparison imported production with domestic production, in the case of common squid, cadmium and arsenic were meaningfully different. The weekly average intakes of Hg, Pb and Cd from dried marine products takes about 1.17~11.52% of PTWI (Provisional Tolerable Weekly Intakes) that FAO/WHO Joint Food Additive and Contaminants Committee has set to evaluate their safeties.