• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.96.2-96.2
• /
• 2012

고체산화물연료전지(SOFC) cell은 cathode, electrolyte 및 cathode층으로 구성되어져 있는데, 이 cell의 적층은 EVD, CVD, sputtering등의 기상공정과 screen printing, tape casting, dip coating등의 습식 공정으로 제조한다. 적층 공정의 경우 supports의 크기와 형태에 따라 적용에 어려움이 있다. 따라서 본 연구에서는 적층공정의 문제점을 해결코자 전사지를 제조하여 평관형 anode supports 위에 적층하여 cell을 제조하였다. 전사지를 이용한 적층방법은 매우 간단하고 두께와 형상제어가 쉽게 가능하였다. 본 연구를 상세히 언급하면 평관형 anode 지지체를 압출법을 통해 제작하였고, 반소된 지지체 위에 anode function layer와 electrolyte(YSZ)층을 형성한 후 $1400^{\circ}C$ 동시 소결하여 치밀한 전해질 층을 형성하였다. 그 후 cthode층을 형성한 후, $1200^{\circ}C$에서 2시간 소결하여 porous한 전극층을 형성하여 cell을 제작하였다. 그 후 Anode supporter위에 전사지를 이용하여 적층한 경우 cell 소결정도를 SEM으로 관찰하였고, 전기화학특성으로는 출력과 분극저항을 측정하였다. 이를 통해 새로운 구성소재 증착방법 즉 전사지를 이용하는 방법을 개발하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.158-160
• /
• 1997

WHEN IT IS REQUIRED TO CONNECT OVERHEAD TRANSMISSION LINE WITH UNDERGROUND CABLE, PREVALENT METHOD WAS TO USE CABLE HEAD TYPICALLY MADE OF LATTICE STEEL STRUCTURE. BUT IN VIEW OF THE INCREASING DEMAND THAT STEEL STRUCTURE INSTALLED IN URBAN AREA AND/OR RESIDENTIAL AREA NEED TO MATCH WITH ENVIRONMENTAL SURROUNDINGS, THE UNSHAPELY LARGE-SIZED LATTICE STEEL STRUCTURE CAN NOT BE A PROPER ONE BECAUSE THAT IT IS NOT WELCOMED BY THE RESIDENTS AND ACCORDINGLY ITS INSTALLATION TENDS TO CONFRONT WITH CIVIL PETITION. AS AN ALTERNATIVE METHOD TO SETTLE AFOREMENTIONED UNFAVOURABLE SITUATION WE MAY BE UNDER, WE AR INTENDING TO DEVELOP THE CABLE HEAD MADE OF TAPERED TUBULAR STEEL POLE AND TO PUT IT TO PRACTICAL USE. THE ADVANTAGE WE CAN TAKE OF THE TAPERED TUBULAR STEEL POLE IS THAT IT CAN BE INSTALLED IN A VERY LIMITED SPACE MAXIMIZING THE UTILITY VALUE OF THE LAND AND THAT ITS SMART SHAPE WITH COLOUR COATING IN CONSIDERATION OF AESTHETIC AESTHETIC CAN BE IN GOOD HARMONY WITH THE SURROUNDINGS.

• 한국수소및신에너지학회논문집
• /
• 제17권1호
• /
• pp.82-89
• /
• 2006

The redox behaviors of anode-supported flat tube for solid oxide fuel cell has been studied. The mass change of the extruded NiO/YSZ anode flat tube during redox cycling was examined by thermogravimetric analysis(TGA). The result of TGA was shown a rapidly mass change in the range of $455\;-\;670^{\circ}C$ and the reoxidation of the NiO/YSZ anode was almost completed at $750^{\circ}C$. The starting temperature of reoxidation and the maximum temperature of oxidation rate decreased with increasing the reoxidation cycle, which is attributed to the increased porosity caused by volume change. Bending strengths of the NiO/YSZ anode after redox cycling were 96 - 80 MPa and the bending strength decreased slightly with increasing the redox cycle. On the other hand, the bending strength of the NiO/YSZ anode with electrolyte showed 130 MPa after first redox cycling but decreased rapidly with increasing the redox cycle. From the results of the bending test and the microstructure observation, we conclude that the crack initiation of the electrolyte-coated NiO/YSZ anode was induced easily at interface of electrolyte/anode tube and propagated cross the electrolyte.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.83.1-83.1
• /
• 2011

고체산화물 연료전지는 전해질의 양쪽에 cathode층과 anode층으로 구성되어 있다. 이러한 셀을 제작하기 위한 구성소재 코팅법으로는 EVD, CVD, sputter등의 기상공정과 screen printing, tape casting, dip coating등의 습식공정이 있다. 이중 현재 가장 널리 사용되고 있는 screen printing법은 코팅기판의 크기와 형태에 제한을 받아 원통형, 평관형에는 적용이 어렵다. 이러한 문제점을 해결하기 위해 본 연구에서는 electrolyte 지지체 위에 전사법을 통해 연료극(NiO-YSZ), 공기극(LSCF-GDC) 코팅층의 두께 및 형상을 제어할 수 있었으며 button cell을 제작하여 실제 SOFC에 적용이 가능함을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.91.1-91.1
• /
• 2011

고체산화물 연료전지(Solid Oxide Fuel Cell이하 SOFC)는 연료가 갖는 화학에너지를 연소과정 없이, 공기와 H2, CO, CH4와 같은 환원성 가스를 공급받아 $600{\sim}1000^{\circ}C$에서 전기화학적 반응을 통하여 직접 전기를 얻는 방식이다. SOFC는 $700^{\circ}C$ 이상의 고온에서 고체산화물이 연료와 공기가 반응하여 전기와 열을 동시에 생산하기 때문에 carnot cycle의 제한을 받지 않아 발전효율이 40% 이상으로 고효율이고, NOx 및 SOx를 배출하지 않아 무공해이며, moving parts가 없어 소음이 나지 않고, 건설과 증설이 지역이나 기후 조건에 제약 없이 용이하고, 다양한 용량이 가능하며, 고가의 백금 촉매를 사용하지 않으며, 수소, 석탄가스, 천연가스 등의 연료를 사용할 수 있는 장점이 있음, 또한 다향한 형태로 제작할 수 있으며 전해질이 고체에서 전해질 손실 및 보충에 문제가 없고 타 연료전지에 비해 개질기가 필요 없어 발전시스템이 간단하고 경량화가 가능하다. 전사법은 paste를 제작하여 전사용지에 Screen printing하여 건조 후 coating하는 방법으로 기존의 여러 coating 방법보다 제작이 용이하고 소재의 크기, 두께조절이 간편하며, 구성층의 표면조도나 굴곡에 대응이 용이한 방법이다. 본 실험에서는 paste 제조, 전사법을 이용하여 Anode, AFL, Electrolyte, CFL, Cathode전사지를 제작하고 이를 세라믹 평관형 지지체에 변수로 두께 조건별 Coating 한 후 $1400^{\circ}C$ 소결을 진행하여 SEM 분석으로 미세구조 관찰, 출력특성 및 Impedance을 확인하였다.

• KEPCO Journal on Electric Power and Energy
• /
• 제5권4호
• /
• pp.257-262
• /
• 2019

Lattice steel towers for overhead transmission lines have been replaced by tubular steel poles due to the visual impact of large and complex shape of truss type. Demand for tubular steel poles consisting of a single frame member continues to grow because of its advantages such as visual minimization, architectural appeal and minimal site consumptions. However, there are some constraints on the transportation and construction. As the diameter of tower base has been enlarged, it may exceed minimum height limit required to pass the tunnel in case of land transportation. Also, in a narrow place where it is not easy to secure the installation areas such as mountainous places, there might be some areas wherein it must secure a wide working space so that large vehicles and working cranes will be allowed to enter. In this paper, we presented a vertical separated tubular steel pole, which is a new type of support that can be implemented for general purpose such as mountainous areas or narrow areas to improve the issues raised by breaking away from the conventional design and fabrication methods. Technical approaches for overcoming the limit of the cross-sectional size is to separate and modularize the cross-section of the tubular steel pole designed with a size that cannot be carried or assembled, and to lighten it with a weight capable of being transported and assembled in a narrow space or mountainous area. As a result of this research, it will be possible to enter small and medium sized vehicles in locations where it is restricted to transport by large-sized vehicles. In the case of mountainous areas, it will be possible to divide it into a weight capable of being carried by a helicopter and it will be easy to adjust and fabricate it with individual modules. Furthermore, in order to break away from the traditional construction method, we proposed the equipment that can be applied to the assembly of Tubular Steel Pole without using a large crane in locations where there is no accessible road or in locations wherein large cranes cannot enter. In particular, this paper shows the movable assembling equipment and some methods that are specialized for vertical separated tubular steel pole consisting of members with reduced weight. The proposed assembly equipment is a device for assembling the body of the Tubular Steel Poles. It will be installed inside the support and the modules can be lifted by using the support itself.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2007년도 추계학술 발표회
• /
• pp.193-198
• /
• 2007

KIER has been developing the anode supported flat tubular SOFC stack for the intermediate temperature $(700{\sim}800^{\circ}C)$ operation. for this purpose, we have first fabricated anode supported flat tubular cells by the optimization between the current collecting method and the induction brazing process. After that we designed the compact fuel & air manifold by adopting the simulation technique to uniformly supply fuel & air gas and the unique seal & insulation method to make the more compact stack. For making stack, the prepared anode-supported flat tubular cells with effective electrode area of $90cm^2$ of connected in series with 12 modules, in which one module consists of two cells connected in parallel. The performance of stack in 3 % humidified $H_2$ and air at $800^{\circ}C$ shows maximum power of 507 W. Through these experiments, we obtained basic & advanced technology of the anode-supported flat tubular cell and established the proprietary concept of the anode-supported flat tubular SOFC stack in KIER.