• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2002.05a
• /
• pp.95-100
• /
• 2002

This study was experimentally performed to investigate flow characteristics of spray droplets in the wind tunnel. Behavior of the spray droplets in the pipe was observed and the deposition rate of droplets on the surface of pipe as liquid film was measured. The experiments were carried out for a variety of parameter, such as velocity of feed air, spray angle of nozzle, and diameter of droplet. From the visual observation of the spray droplets in the pipe and the measurement of deposition rate on the pipe, the general understanding of droplets behavior for desuperheater was provided.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.729-734
• /
• 2001

Thermal stratification due to turbulence penetration and in-leakage of valve cause the large thermal stress, which lead to fatigue crack of the piping system of nuclear power plant. So it is needed that numerical and experimental study for the phenomenon is conducted because there have not yet been sufficient study for the relationship between turbulence penetration and thermal stratification. Therefore numerical analysis is done here and respected to give a fundamental method of the approach to the phenomenon.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.7
• /
• pp.667-673
• /
• 2000

In order to understand the laminar flow heat transfer enhancement by the swirl flow, the effects of heat transfer in a circular pipe with a twisted tape insert were investigated experimentally. In the present study, the uniform heat flux condition was considered. The laminar heat transfer correlations were developed using the least-square-fit from the surface temperature distribution of an electrically-heated pipe and flow property data. Average Nusselt number correlations with the twisted tape insert were expressed as a function of swirl parameter, Reynolds number and Prandtl number. In the case of the twisted ratio y = 6.05, the mean Nusselt number increased approximately 500% and the friction factor increased approximately 300%, compared to the case of the empty pipe, respectively.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.6 no.3
• /
• pp.227-236
• /
• 1994

Steady flows of Newtonian and non-Newtonian fluids in the stenotic tubes with various stenotic shapes are numerically simulated. Validity of the modified power-law model as a constitutive equation for the purely viscous non-Newtonian fluid is discussed and the results of the power-law model are compared with those of the Carreau model, the Powell-Eyring model and experimental data for blood. Flow characteristics and reattachment lengths for non-Newtonian fluids in the stenotic tubes are presented extensively. Also, the analysis is extended to predict the influences of diameter ratio, stenosis spacing, number of stenosis and Reynolds number on the flow characteristics in the multiple stenotic tubes.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.04a
• /
• pp.217-222
• /
• 1995

소음기의 음향 성능을 평가하기 위해서는 음원의 임피던스를 알아야 한다. 음원의 임피던스를 구하기 위한 많은 연구가 행해졌고 정재파법, 음향전달함수법, Two Load Method(TLM), Four Load Method(FLM)등이 여러가지 방법이 개발되었다. 정재파법은 저주파수에서 음원의 출력보다 큰 출력음을 발생시킬 수 있는 스피커가 있어야 하고, 주파수별로 반복 측정해야 하는 번거로움으로 인해 실험에 어려움이 따른다. 전달함수법과 Two Load Method(TLM)는 관내에서 음압을 측정해야 하는데 엔진의 흡배기계와 같이 음압이 높거나 고온의 가스 유동이 있는 경우 측정이 매우 어렵다. 한편 Four Load Method(FLM)는 외부의 방사 음압을 측정하여 음원의 특성을 구하기 때문에 위에서 언급한 문제점들이 없는 반면에 무향실을 이용해야 한다. 본 논문은 음원의 임피던스 측정의 여러 방법 중 FLM에 의하여 스피커 음원의 임피던스를 측정하고 삽입손실을 구하면서 FLM이 가진 문제점을 검토하였다.

• Journal of the Korean Society of Safety
• /
• v.9 no.2
• /
• pp.3-11
• /
• 1994

This study discribes result of comparision of two other numerical method, method of characteristics (MOC) and Lax-Wendroff method(LWM) applied at wave action analysis of Intake and exhaust pipe. Partiality FCT(Flux Correct Transport) scheme is appeneded to LWM to protest unacceptable overshoots, occuring near discontinuity. The final conclusion of this study is that MOC should be replaced by a second order finite difference approach(such as the LW method). Clear benefits we can get by change are faster calculation, higher accuracy, conservation of mass and consistent calculation method.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.41-45
• /
• 2011

Pressure drops of two-phase flow in a pipe according to particle shapes have been calculated and analyzed. The numerical analysis for 3 cases of Reynolds number has been conducted for each particle shape. In case of the cylinder shape, the particles had been assumed to be randomly distributed for each Reynolds number. The results have been averaged and compared to those of the case of the ball shape. Additionally, pressure drops of ball and cylinder shapes has been compared to the result of Ergun's equation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.5
• /
• pp.52-57
• /
• 2000

Recently large capacity of electric equipment and increasing in atomic power generation are shown. One of the reason is shortage of the electric power supply for air conditioning load during summer. And every consumer is concerning about economical refrigeration and air conditioning system to decreases electric power consumption and decrease in global warming. For these necessities, ice making thermal storage system is required. Therefore, in this paper, the possibility of continuous slurry ice making using flowing organic water solution in cooled circular tube has been investigated. The experiments was carried out under some parameters of concentration and velocity of water solution, temperature of cooled tube wall, and control pressure in tube, As a result, four types of operating conditions in the pipe, that was supercooling, continuous ice making, intermittent ice making and ice blockage, were classified . And it was found that the critical condition for continuous ice making was acquired as a function of these experimental parameters.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.11
• /
• pp.1499-1508
• /
• 1998

A numerical study is performed to investigate pressure drops, particle trajectories and erosion around orifice plates in pulverized coal pipe lines. Particle impaction rates change significantly with orifice shapes and Stokes numbers. At Reynolds number of $5{\times}10^5$, the pulverized coal flows well with streamlines and do not collide at the orifice plates at small sizes (${\sim}20{\mu}m$). However, the large particles (over $70{\mu}m$) impact on the front face of the orifice and erode the orifice surface. The pressure loss coefficients around the erode orifice are largely different from the designed original orifice.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.6
• /
• pp.689-696
• /
• 2008

In a water treatment process a complete and homogeneous dispersion of the coagulants in the raw water could be most important factor. This research was performed to evaluate coagulation performance of the in-line-orifice mixer which was recently introduced as a rapid mixing device. The test was to determine the actual coagulant dispersion distribution on the overall cross-section at a distance of 1.6~3D from the chemical injection point by measuring zeta potential. From the results of zeta potential test, it was shown that the coagulant dispersion within the in-line orifice mixer was occurred very unevenly. The results have confirmed that it is necessary to increase the velocity of coagulants injection or pressurized water rates, in order to reduce nonuniform distribution of chemicals.