• Korean Journal of Materials Research
• /
• v.10 no.1
• /
• pp.83-89
• /
• 2000

$Si_3N_4$ powder with 2wt% $Al_2O_3$ and 6wt% $Y_2O_3$ additives was sintered by gas pressure sintering (GPS) technique. The variations in the unlubricated wear behavior depending on sintering time were compared. Tribological properties depending on sintering time are associated with fracture toughness as well as flexural strength of materials. When increasing the sintering time, the larger elongated grains were formed as a result of exaggerated grain growth. As the fracture toughness and flexural strength decreased, the wear volume increased. On the basis of these experimental results, the unlubricated wear properties of silicon nitride were found to be governed mostly by both the fracture toughness and the flexural strength of the material.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.58-65
• /
• 2004

A cylindrical constant volume combustion chamber was used to investigate the combustion characteristics of stratified methane-air mixture under several initial charge conditions in the author's previous reports. The results showed that the improvement of thermal efficiency and reduction of heat loss was realized simultaneously by using 2-stage injection method. This paper deals with the reason why the stratified combustion has showed better combustion rate through the measurement and analysis of chemiluminescence of C $H^{*}$ and $C_{2}$$^{*}$ radicals. An optic fiber bundle is used to measure the local emission of C $H^{*}$ and $C_{2}$$^{*}$ radicals to map the relationship between the excess air ratio and local radical intensity ratio in the combustion vessel at 5 mm apart form the geometric center. The results show that there exist a relationship between the intensity ratio and the air-fuel ratio. It is revealed that the improvement of combustion rate in a lean-stratified mixture is realized through the 2-stage injection method. method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.2
• /
• pp.215-226
• /
• 2003

Experimental and numerical studies have been done to examine the effects of excess air ratio and tertiary air swirl number on the formation characteristics of NOx in a pilot scale combustor adopting a multi-air staged burner. In numerical calculation the mathematical models for turbulence, radiation and nitric oxide chemistry were taken into account. The radiative transfer equation was solved using the discrete ordinates method with the weighted sum of gray gases model. In the NOx chemistry model, the chemical reaction rates for thermal and prompt NOx were statistically averaged using a probability density function. The results were validated by comparison with measurements. For the experiment, a 0.2 MW pilot multi-staged air burner has been designed and fabricated. Using the numerical simulation developed here, a variation of thermal and prompt NOx formation was predicted by changing the excess air ratio and tertiary air swirl number. As the excess air ratio increased up to 1.9, the formation of the total as well as thermal NOx at exit increased while the prompt NOx decreased. The formation of thermal NOx was more affected by concentration of $O_2$ and $N_2$ than gas temperature. When the tertiary air swirl number increased, the formation of the total as well as the prompt NOx slightly decreased.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.253-259
• /
• 2013

In the present study, the characteristics of combustion phenomena and NOx emission in the OFA-type tangentially injected coal-fired boiler have been investigated numerically in order to find the effect of geometrical variation on the performance of the boiler. For these, numerical analyses of turbulent flow, chemical reaction, and radiation heat transfer are performed by using the computational fluid dynamics method. The predicted results clearly show that NOx formation highly depends on the combustion processes, the temperature and species concentrations. In addition, the optimum conditions for both the maximum NOx reduction and highest boiler efficiency can be obtained by considering the amount of supplied air and the injection angle at OFA, and modifying the boiler configuration. It is also found that the variation of supplied air at OFA is more effective than that of the injection angle for reducing the NOx emission, within the present operating conditions.

• 한국연소학회:학술대회논문집
• /
• 2006.10a
• /
• pp.53-59
• /
• 2006

This study is measurement of radicals in gas & light oil diffusion flame focused on burner exit. The goal of this study is to analyse the relationship between flame chemiluminescence($OH^{\ast}$, $CH^{\ast}$, $C_2^{\ast}$) intensities and flame conditions. The investigation performed turbulent diffusion flame of commercial burner in varying the excess air ratio from 1.0 to 1.8. The optical emissions were measured by photomultiplier(PMT) using optical band pass filter and spectrometer system. The effects of excess air ratio and NOx emission characteristics on the radical emission intensities were investigated experimentally.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.1
• /
• pp.115-123
• /
• 2001

This study describes the combustion characteristics under various condition of air excess ratio and ignition timing in a 2-valve gasoline optically accessible engine with swirl control valve(SCV). It adapted three different types of SCA(open ration 72.5%, 78%, 89%) to strengthen a swirl flow. Pressure data were acquired using pressure sensor to investigate the effect of swirl flow on combustion, and from these pressure data, IMEP(indicated mean effective pressure) and MFB(mass fraction burnt)were calculated to explain burn rate and flame speed. From acquired flame images, inspected the flame propagation direction, flame area, and flame centroid, Flame propagation direction was shown different tendency between with/without SCV, and flame area with SCV was faster and larger than that of conventional engine. Finally, the representative flame image at each crank angle were acquired by PDF method to verify flame growth process. It is found that strengthened swirl flow is more beneficial for faster and stable combustion.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.70-76
• /
• 2002

This study focus on the effect of engine specification, driving conditions and the vehicle type on the idle emission characteristics. In order to obtain the characteristics of exhaust emissions, 1,260 vehicles of spark ignition engine are sampled and investigated. The exhaust emissions are measured with a CO/HC emission gas analyzer. The Sl engine vehicles are investigated by the effect of various exhaust emission parameters such as vehicle milage, engine specification, valve trains and fuels. The results show that the amount of CO and HC emission is not directly related to the driving mileage of the vehicle. However, the engine specifications and fuels such as the type of valve train and piston displacement have influence on the exhaust emissions. In addition, the LPG vehicle emits more CO and HC than gasoline vehicle. Based on the test results of SI vehicles, the influence of excess air and displacement volume are discussed.

• Journal of the Korean Society of Safety
• /
• v.14 no.3
• /
• pp.84-92
• /
• 1999

The effects of air velocity and excess air on combustion characteristics were studied in a fluidized bed combustor. The domestic low-grade anthracite coal with heating value of 2010 kcal/kg and the imported bituminous coal from Australia with heating value of 6520 kcal/kg were used as coal samples. The combustion characteristics of mixed fuels in a fluidized bed combustor could be interpreted by pressure fluctuation properties, ash distribution and gas emission. The properties of the pressure fluctuations, such as the standard deviation, cross-correlation function, dominant frequency and the power spectral density function, were obtained from the statistical analysis. From this study, the combustion region increased with increasing air velocity but decreased with excess air due to combustion characteristics of anthracite and bituminous coal.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.65-70
• /
• 2003

In this paper, an adapted TWC model and its application to the monitoring algorithm are proposed. As TWCs have the different characteristics, the model has to be corrected to diagnose more accurately. In the TWC model oxygen storage and release rate model are adapted to the installed TWC to whose characteristics related. The model learns from the downstream $O_2$ sensor output during the vehicle's operation. From the results, the model is adapted to the Installed TWC's characteristics. using this model, the monitoring algorithm can diagnose the no more accurately. Finally the algorithm is validated with simulations using the data logged from a retail car.

• 한국연소학회:학술대회논문집
• /
• 2001.11a
• /
• pp.1-7
• /
• 2001

FGR is one of the most widely used methods of NOx reduction in the combustion process. It was investigated the effect of FGR, excess air ratio, peak temperature and firing rate on NOx emission in this study. 100kW burner and LNG were adopted in this experiment. NOx emission was notably decreased with the increase of FGR, however CO emission was also drastically increased in the 25% FGR. And excess air ratio, peak temperature and firing rate did not affect the NOx emission appreciably in the normal operating condition.