• Food Science and Preservation
• /
• v.24 no.5
• /
• pp.600-607
• /
• 2017

This study was conducted to develop radish as a food product for home meal replacement using superheated steam (SHS). Also, the change of quality characteristics was studied during their storage. The radish cuts were treated with SHS for 0, 3, 5, and 7 min, respectively, followed by complete drying at $80^{\circ}C$ for 6 hours. The results showed that radishes restored with mixed solution (drinking water:sugar:vinegar:salt=2:1:0.8:0.1) were harder than those restored with drinking water. All radishes were stored at 5, 10 and $15^{\circ}C$ for 56 days to investigate the changes of quality characteristics during the storage. Radishes in the control group, restored with drinking water and stored at $15^{\circ}C$, were spoiled after 7 days of storage. The radish in the experimental group did not show any change in the water content; except an increase on the first day of storage. The hardness of radish decreased with an increase in the storage period. It was found that microbial growth was inhibited due to low pH of the mixed solution, in which radishes of the experimental group were immerse.

• Food Science of Animal Resources
• /
• v.27 no.4
• /
• pp.416-423
• /
• 2007

This study investigated the effect of ohmic thawing on the physicochemical properties of pork meat. The physicochemical properties of pork meat thawed by brine immersion and electrode contact ohmic systems were compared. A more rapid thawing rate was seen with the electrode contact thawing system than with brine immersion. No significant differences in pH were found with increasing voltage for both thawing methods (p>0.05). Increasing the voltage level tended to decrease drip loss, resulting in increased water holding capacity. The shear forces of pork thawed at 50 V did not differ from the control (p>0.05) for both thawing methods. Although significantly high TBARS (p<0.05) values were found at 20 and 40 V for immersion, and 0 V for contact thawing, increasing the voltage level tended to decrease the TBARS values. Regarding TVBN, no significant effect was observed with increasing voltage levels (p>0.05). The total color difference of pork was significantly higher (p<0.05) with immersion thawing than with electrode contact thawing. These results indicate that brine immersion thawing is favorable at high voltage levels, while lower voltage levels are applicable for electrode contact thawing.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.8
• /
• pp.1546-1552
• /
• 2016

In addition, because it uses preheating to dissolve an alloy in general, it is hard to regulate the appropriate melting temperature of the alloy and brewing time and shows the defect of the supplementation thing due to the super-heating. Once the alloy is molten and then most of the casting by attaching a sight glass or non-contact temperature sensor is suitable casting temperature the operator pressing a button to generate a centrifugal force to inject the molten alloy into a crucible in the casting ring. These results, and most of the cast temperature is too high or too low to generate a lot of casting defects do not get into a uniform cast body. In this paper, we developed a dental casting machine for high frequency using a single temperature sensor which can measure the actual temperature of the alloy than the temperature of the external non-contact measurement using a temperature sensor.

• Plant Journal
• /
• v.14 no.2
• /
• pp.33-38
• /
• 2018

The CFB boilers technology is facing a number of challenges. Among them, boiler tube erosion, sintering by bed inventory overheating and high self consumed service power are major ones. This study was conducted to obtain allowable bed inventory with the Yeosu Power Plant, a 300 MW class CFB boiler. For the test, bed pressure was reduced from design pressure of 4.5 KPa to 2.5 KPa by reducing bed inventory, at fixed turbine output, coal consumption rate and air flow. Consequently, reducing the lower bed inventory is effective to decrease bed temperature but excessive reducing might increase bed temperature due to lack of circulating fluidized materials. Also, in case of the Yeosu Plant boiler using subbituminous coal as its primary fuel, its bed temperature change is highly affected by not only the amount of bed inventory, but also the boiler capacity and coal contents.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.11
• /
• pp.634-640
• /
• 2020

Failure analysis and heat-resistant were performed for an electric fuel pump that is installed in the fuel tank to transfer fuel to the engine of combat vehicles. The fuel pump with a DC motor was disassembled and inspected to determine the cause of failure. The failure phenomenon was classified into three categories based on observations of the inside of the housing: burnt winding, quick brush abrasion, and fuel leak into the pump. Based on the inspection results, it was estimated that overheating was the main cause of failure. The thermal test was conducted under the no-load condition in 24 hours, and the thermal sensor was installed on the stator surface and the brush holder to check the possibility of damage to the winding due to overheating. When the ambient temperature of the fuel pump was set to 68 ℃, the stator temperature increased to 135.9 ℃, and the winding of the motor was almost damaged. The test results confirmed the lack of heat resistance of fuel pump windings, and suggested that the type F of insulation class (below 155 ℃) of the windings and varnish should be replaced with type C or higher that can be used above 180 ℃.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.2
• /
• pp.238-243
• /
• 2011

The ambient temperature of the experimental conditions changes by varying the speed of the compressor and the electronic expansion valve opening. The effects of changing valve opening to the entire system has been investigated. The results show that the ambient temperatures of $35^{\circ}C$ and $30^{\circ}C$ controlled at 30Hz must be avoided. The capacity control range of the control compressor with changing speed is about 43~100% at $35^{\circ}C$, 43~100% at $25^{\circ}C$ and 48~100% at $10^{\circ}C$, respectively. The results show the capacity control range decreases with decreasing ambient temperature.

• Journal of Energy Engineering
• /
• v.19 no.3
• /
• pp.156-162
• /
• 2010

3-D CFD(Computational Fluid Dynamics) work were carried out to investigate the combustion characteristics in a boiler depending on the variations in air supply condition. For the gas temperature, $O_2$, NO, SOx at the outlet of economizer, the predicted values were been compared with the measured data. With the verified CFD model, the effects of air flow rates through SOFA(Separated Over Fire Air) and CCOFA(Closed Coupled Over Fire Air) on the combustion behavior in a boiler were simulated, and the distributions of NOx and gas temperature were mainly compared each other. The change in SOFA air flow rate gave the more sensitive effect on NOx than that in CCOFA. The distributions of gas temperature at convection path are differed with the changes in SOFA and CCOFA flow rate, so the combustion modification such as yaw anlge adjustment are required to get an enhanced gas temperature distribution.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.833-839
• /
• 2013

Thermal vacuum test should be performed prior to launch to verify satellites' functionality in a harsh space environment which is represented by extremely cold temperatures and vacuum conditions. A thermal vacuum chamber which consists of a vacuum vessel, a pumping system, and a thermal control system are used to perform thermal vacuum tests of a satellite system and its components. A cryogenic blower is a core component of the closed loop thermal control system for thermal vacuum chambers. This paper describes the fan design of the cryogenic blower, the design of the thermal protection interface between the driving part and the fluid part, which were verified by thermal and structural analyses. The performance of the cryogenic blower is confirmed by similarity test on the test bench.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.11
• /
• pp.1008-1015
• /
• 2015

Thermal vacuum test should be performed prior to launch to verify satellites' functionality in extremely cold/hot temperatures and vacuum conditions. A thermal vacuum chamber used to perform the thermal vacuum tests of a satellite system and its components. A cryogenic blower is a core component of the gaseous nitrogen (GN2) closed loop thermal control system for thermal vacuum chambers. A final goal of this research is development of cryogenic blower. Design requirements of a blower are 150 CFM flow rate, 0.5 bara pressure difference, hot and cold temperatures. This paper describes the performance analysis of impeller by 1D, CFD commercial software, the design of the thermal protection interface between the driving part and the fluid part. The performance of the cryogenic blower is confirmed by test at the standard air condition and is verified by on the thermal vacuum chamber at the real operating condition.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.6
• /
• pp.768-773
• /
• 2012

This study was performed to find out the possibility that hot waste water from a thermoelectric power plant can be applied to Organic Rankine Cycle (ORC) by comparing the performance characteristics for use of the ocean surface water ($25^{\circ}C$) and hot waste water ($35^{\circ}C$) as a secondary fluid. The parameters considered in this study are four; superheating temperature, subcooling temperature, turbine efficiency, and pump efficiency. Main results of this study are summarized as follows : Overall efficiency of applying hot waste water to ORC is 87% higher than that of surface water. Thus it could be confirmed that hot waste water of the thermoelectric power plant can be applied to ORC.