• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.6
• /
• pp.482-489
• /
• 2018

Most of the numerical and experimental studies on supercavitating flows are focused on the cavitator only. However, the partial cavity growing into the supercavity is affected by the shape of the body placed behind the cavitator. In this paper, we develope a numerical method which is based on the boundary element method to predict supercavitating flow around three-dimensional axisymmetric bodies. We estimate the influence of the body shape on the supercavity growth. Here, we consider various parameters of the body such as cavitator shape, shoulder length and body diameter, and compare the results with the case of the cavitator only. In summary, it is found that the body may impede the cavity growth, the shoulder mainly affects the cavity length, and the supercavity occurring in the cone type cavitator is strongly influenced rather than that of the disk type cavitator.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.2
• /
• pp.237-244
• /
• 2021

In recent years, the maturity of the technology for a high speed underwater vehicle using supercavitation increase, it is entering the stage of applied research for practical use. In this study, hydrodynamic performance of the supercavitating object was evaluated by using a Viscous-Potential based Boundary Element Method(VP-BEM). 27 models with different shape parameters such as body diameter, length and fore-body shape were considered. The process of the supercavity development of each model was simulated, and drag generated according to operating conditions such as changes in water depth was analyzed.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.1
• /
• pp.10-20
• /
• 2014

To study the water-entry impact noise, on-board experiment using a small launcher firing various objects was performed in the Yellow Sea. As the launcher fires a cylindrical object from the ship vertically, generated noise is measured with a hydrophone on the starboard of Chung-hae, Marine surveyor. Three types of cylindrical objects, which have noses of flat-faced, conical, and hemisphere, were used during the experiment. The measured noise exhibits a time-dependency which can be divided into three phases: (1) initial impact phase, (2) open cavity flow phase, (3) cavity collapse and bubble oscillation phase. In most cases, the waveform of bubble oscillation phase is dominant rather than that of initial impact phase. Pinch-off time, where a cavity begins to collapse, occurs at 0.18 ~ 0.2 second and the average lasting time of bubble was 0.9 ~ 1.3 second. The energy of water-entry impact noise is focused in the frequency region lower than 100 Hz, and the generated noise is influenced by the nose shapes, object mass, and launching velocity. As a result, energy spectral density on the bubble frequency is higher in the order of flat-faced, conical, hemisphere nose, and the increase of initial energy raises the energy spectral density on the bubble frequency in the cylinder body of same shape. Finally, we compare the measurements with the simulated signals and spectrum based on the bubble explosion physics, and obtain satisfactory agreements between them.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.1
• /
• pp.19-26
• /
• 1996

An experimental and computational study of the pressure fluctuation induced by a propeller on a hull surface was carried out with three ship models and seven model propellers. The fluctuation of pressure on a flat plate was measured at KRISO cavitation tunnel and calculated by a panel and lifting surface method(XForShip code). To extend the measurement data on the flat plate into that on complex hull forms, the correction factor was determined as a ratio of the solid boundary factor(SBF). The computation of pressure fluctuation around complex hull forms was also performed to make the full scale prediction and compared with the corrected experimental data. The calculated values agreed well with the compensated experimental data and it was found that the correction factor was about 0.65-0.7.

• Journal of Sensor Science and Technology
• /
• v.11 no.5
• /
• pp.263-272
• /
• 2002

In this paper, we investigate the potential for retrieval of morphometric data from three dimensional images of conducting bronchus obtained by X-ray Computerized Tomography (CT) and to explore the potential for the use of rapid prototype machine to produce physical hollow bronchus casts for mathematical modeling and experimental verification of particle deposition models. We segment the bronchus of lung by mathematical morphology method from obtained images by CT. The surface data representing volumetric bronchus data in three dimensions are converted to STL(streolithography) file and three dimensional solid model is created by using input STL file and rapid prototype machine. Two physical hollow cast models are created from the CT images of bronchial tree phantom and living human bronchus. We evaluate the usefulness of the rapid prototype model of bronchial tree by comparing diameters of the cross sectional area bronchus segments of the original CT images and the rapid prototyping-derived models imaged by X-ray CT.

• Tunnel and Underground Space
• /
• v.16 no.1 s.60
• /
• pp.11-25
• /
• 2006

The world's largest nucleon decay experiment facility is constructed at a depth of approximately 1,000 meters, in the Kamio Mine, Japan. The excavated cavern is consisted of a cylinder of 42.4 m high and a semi elliptical dome of 15.2 m high, with a bottom diameter of 40 m. The total excavation volume is approximately $69,000\;m^3$. Because of the character as a large cavern excavation in deep underground, there is many unknown factors in rock mechanics. Based on the results of rock test and numerical analysis, the monitoring of rock mass behavior accompanying progress of construction was performed by various instruments installed in the rock mass surrounding the cavern. The monitoring data was used in the study of measures for cavern stability.

• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.63-68
• /
• 2008

This paper describes about the simulation and the experimental results of optical cavity with curved mirror surface and vertical mirror surface to improve the light intensity and efficiency of the optical sensors. When we use the vertical mirror surface, the distribution of light reached to the filter surface of detector shows an elliptical shape. Whereas, the curved mirror surface focuses the light into circular shape. Therefore, due to focusing effects in case of using curved mirror surface, the light intensity per unit area has been improved. Consequently, the output voltage of gas sensor has been expected to increase. Based upon the simulation, the experiment of gas sensor has been conducted with $CO_2$ gas from 0ppm to 2,500 ppm at 250 ppm step and $25^{\circ}C$, 45%R.H. ambient. The output voltage of gas sensor that has a curved mirror surface increases approximately 200 mV than that of vertical mirror surface.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.3
• /
• pp.143-151
• /
• 2015

The Crack, occurred in the concrete structure, is a major cause of function deterioration such as strength, durability and waterproof. Therefore the need for crack reduction will continue as long as there is concrete structure. But, it is not easy to reduce or prevent crack cause of impact factor of it. There are so many factors of crack such as material, construction and maintenance environment, and structure, and these are acting in combination. So, this study derives a correlation between the cracks and members through reviewing member crack occurred. And member's attribute, related crack, is analyzed by it. It consider that the basic attribute of member is similar when its requirements are similar. Through this study, therefore, foundation of countermeasure of crack will be provided by prediction of crack shape through member's attribute.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.2
• /
• pp.153-161
• /
• 2009

After several PWSCCs were found in Bugey(France), Ringhals(Sweden), Tihange(Belgium), Oconee, Arkansas, Crystal Fever, Davis-Basse, VC Summer(U.S.A.), Thuruga(Japan), USNRC and PNNL started the research on PWSCC, that is, PINC project. The aim of this project is to fabricate and obtain representative NDE mock-ups with flaws to simulate tight PWSCC cracks, to identify and quantitatively assess NDE methods for accurately detecting, sizing and characterizing tight cracks such as PWSCC, to document the range of locations and crack morphologies associated with PWSCC and observed responses and to incorporate findings from other ongoing PWSCC research programs, as appropriate. By participating in PINC project, Korean morphology technique about PWSCC and NDE technique have improved and become similar lever with other advanced country. Therefore, the evaluation technique of integrity for nickel alloy component has been improved by cooperation with university, research institute and industries.

• Journal of KIISE:Computing Practices and Letters
• /
• v.15 no.10
• /
• pp.796-800
• /
• 2009

Currently, there are many software tools that can generate 3D human figure models and animations based on the advancement of computer graphics technology. However, we still have problems in interoperability of human data models in different applications because common data models do not exist. To address this issue, the Web3D Consortium and the ISO/IEC JTC1 SC24 WG6 have developed the H-Anim standard. However, H-Anim does not include human motion data formats although it defines the structure of a human figure. This research is intended to obtain interoperable human animation by defining the data for human motions in H- Anim figures. In this paper, we describe a syntactic method to define motion data for the H-Anim figure and its implementation. In addition, we describe a method of specifying motion parameters necessary for generating animations by using an arbitrary character model data set created by a general graphics tool.