• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2407-2414
• /
• 1992

Constant temperature hot wire air flow meter for automobiles requires temperature compensation system because hot wire output signal is sensitive to ambient temperature variations as well as fluid velocity. The objectives of the present study are to design an air flow meter circuit which is capable of compensating the hot wire output signal for ambient temperature variations and to investigate the mechanism of such temperature compensation. This circuit is composed of platinum hot wire, platinum resistor, two variable resistors, a constant resistor and a DC-amplifier. In particular, by simply replacing a constant resistor in one of the bridge arms of the conventional circuit with platinum resistor and a variable resistor for the purpose of temperature compensation, the deviation of output signal with respect to ambient temperature variations between 27deg. C 70deg. C could be reduced to less than 2.5% for mass flow rate and to less than 5% for velocity respectively. The mechanism of temperature compensation against ambient temperature variations was explained by means of measuring the heat transfer coefficient with hot wire temperature variations and analyzing and analyzing conventional empirical equations qualitatively.

• Resources Recycling
• /
• v.14 no.2
• /
• pp.3-9
• /
• 2005

A study on the air and gravity separation has been performed for the removal of chlorine containing materials from ASR of end-of-life vehicles. The gravity separation was also conducted on waste plastics collected from ASR. In this work, ASR were previously shredded to pass through 8 mm sieve prior to separation tests and the gravity separation of waste plastics was conducted for three different particle sizes. The two-stage air classification was conducted with the range of air flow rate of 9~20 M$^3$/hr at first stage and 25~34 M$^3$/hr at second stage, respectively. The fraction of overflow product was remarkably increased in the 2nd stage air classification because of high air flow rate while that of underflow product obtained from 1st stage air classification was found to be 62~66%. From the results of gravity separation on waste plastics, it was also found that the amount of the float product was much greater than sink product. It is believed that the gravity separation may be used very efficiently for the removal of calorine bearing materials from waste plastics.

• Applied Chemistry for Engineering
• /
• v.33 no.1
• /
• pp.96-102
• /
• 2022

Reactants of PEMFC are hydrogen and oxygen in gas phases and fuel cell overpotential could be reduced when reactants are smoothly transported. Numerous studies to modify cathode flow field design have been conducted because oxygen mass transfer in high current density region is dominant voltage loss factor. Among those cathode flow field designs, a block in flow field is used to forced supply reactant gas to porous gas diffusion layer. In this study, the block was installed on a simple fuel cell model. Using computational fluid dynamics (CFD), effects of forced convection due to blocks on a polarization curve and local current density contour were studied when different air flow rates were supplied. The high current density could be achieved even with low air supply rate due to forced convection to a gas diffusion layer and also with multiple blocks in series compared to a single block due to an increase of forced convection effect.

• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.321-326
• /
• 2022

As the thickness of the polymer membrane of PEMFC(Proton Exchange Membrane Fuel Cells) is getting thinner for PEMFC performance and price reduction, research on improving durability has become more important. In the durability evaluation of membranes, the mechanical durability evaluation time is more than twice that of the chemical durability evaluation time, so it is necessary to select the durability evaluation conditions well. In this study, we tried to check how much the mechanical durability evaluation time changes when there is a difference in the inflow gas type and flow rate in the mechanical durability evaluation protocol (Wet/Dry). When nitrogen was used at a flow rate of 2,000 mL/min, the evaluation time increased by 1.25 times compared to when air was used. An increase in the degradation rate of the electrode Pt was the main factor when air was used. When the flow rate was reduced to 800 mL/min, the air and nitrogen evaluation times increased by 1.5 times and 1.2 times, respectively.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.992-995
• /
• 2010

엔진 흡기시스템 중 흡기매니폴드는 가솔린엔진의 성능을 결정하는 매우 중요한 성능 인자이다. 본 연구에서는 1400cc급 가솔린 엔진용 흡기 매니폴드에 대한 유동해석과 리그 실험을 수행하였다. 압력차에 따른 유동 및 유량계수의 해석을 통하여 유동특성을 분석하였으며 실험적 평가를 통하여 공기유량계수의 결과치를 검증하였다. 해석과 실험 결과를 비교 분석하여, 해석값과 실험값의 오차를 확인하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.115-118
• /
• 2010

2 Types of heater (Vitiated Type, Clean Air Type) in order to increase the temperature for a test are used for industry. In this report, large capacity clean air type heater was designed. Heater capacity and LNG consumption rate can be calculated by the air mass flow and heater inlet/outlet temperature. The heater is composed by Burner, Furnace, Heat Exchanger, and Stack. The hot air from the burner and cold air from the tube inlet exchange their heat indirectly in the heat exchanger, so the desired temperature can be achieved at the exit of the tube.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2002.05a
• /
• pp.245-250
• /
• 2002

보일러의 압입송풍기 토출구로부터 나온 연소용 공기를 버너가 있는 장소로 이동시키기 위해 설치하는 풍도(air duct)는 보다 원활한 연소용 공기의 공급과 효율적인 운송을 통하여 연소로에서 배출되는 연소 배출물인 SOx, NOx 등이 최소가 될 수 있도록 연소운전조건을 개선하여 연소로 내부에서의 화염을 안정화시킴으로 고효율 보일러의 운전환경을 제공할 수 있기 때문에 설계 단계에서 충분한 연구가 필요하다고 보여진다.(중략)

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.491-492
• /
• 2010

기존에 사용중인 저압용 벤튜리 타입 혼합기는 0.32kg/cm2에서 열리고 0.28kg/cm2에서 닫히도록 설정되어 있다. 이 방식은 증가하는 도시가스 공급량을 따라갈 수 없기 때문에 강제 혼합기를 개발 현장에 적용하고자 한다. 본 연구를 통해서 개발하고자하는 강제 혼합기는 제어밸브을 통하여 가스 62.5%, 압축공기 37.5%의 비율로 희석하여 서지탱크로 보내진다. 완성된 혼합기를 이용한 열량실험 결과 유량이 변하여도 일정한 열량이 나옴을 알 수 있었다.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.9
• /
• pp.948-954
• /
• 2008

Membrane bioreactor(MBR) processes have been widely applied to wastewater treatment for last decades due to its excellent capability of solid-liquid separation. However, membrane fouling was considered as a limiting factor in wide application of the MBR process. Excess aeration into membrane surface is a common way to control membrane fouling in most MBR. However, the excessively supplied air is easily dissipated in the reactor, which results in consuming energy and thus, it should be modified for effective control of membrane fouling. In this study, cylindrical tube was introduced to MBR in order to use the supplied air effectively. Membrane fibers were immersed into the cylindrical tube. This makes the supplied air non-dissipated in the reactor so that membrane fouling could be controlled economically. Two different air supplying method was employed and compared each other; nozzle and porous diffuser which were located just beneath the membrane module. Transmembrane pressure(TMP) was monitored as a function of airflow rate, flux, and ratio of the tube area and cross-sectioned area of membrane fibers(A$_m$/A$_t$). Flow rate of air and liquid was regulated to obtain slug flow in the cylindrical tube. With the same flow of air supply, nozzle was more effective for controlling membrane fouling than porous diffuser. Accumulation of sludge was observed in the tube with the nozzle, if the air was not suppled sufficiently. Reduction of membrane fouling was dependent upon the ratio, A$_m$/A$_t$. For diffuser, membrane fouling was minimized when A$_m$/A$_t$ was 0.27, but 0.55 for nozzle.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.4
• /
• pp.103-111
• /
• 2009

Moisture is one of the important design factors that affects to the changes of physical properties and air permeability in the composting matrix. This study examines the effects of moisture during the wetting and drying procedure on physical properties like bulk density, particle size, free air space and air permeability in the sawdust used as the bulking agent in composting process. During both procedures of wetting and drying of the water, with increasing moisture content, bulk density and particle size increased, but FAS decreased. In the range of near 40 to 60% moisture content on a wet basis, particle size and FAS in wetting procedure were larger and higher than those in drying procedure. During wetting procedure, pressure drop continuously decreased ranging from near 20 to 60% moisture content, despite of decreasing FAS as a consequence of increasing moisture, and then over the range of 60% moisture content, pressure drop rapidly increased to the saturated moisture condition while the pore space was filled with the water. On the other hand, during drying procedure, pressure drop decreased from the saturated condition to 40% moisture content. In the recommended range of 50 to 60% moisture content for composting operation, pressure drop in wetting procedure were lower than in drying procedure. For the enhancement of the air permeability in the composting matrix, the wetting procedure was proper than the drying procedure, and the optimum moisture content for the efficient composting operation was appeared to be near 60%.