• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.9-14
• /
• 1999

The effect of operating condition was studied experimently on the characteristics of twin sprays ejected from two airblast atomizers, within the range of the mass air-fuel ratio 1.36∼3.54. Water and nitrogen gas were used as test fluids for the experiments. Spray characteristics of liquid spray were measured with measurement of mass distribution and instantaneous image of the spray cone. Experimental results show that the maximum specify of the distribution were lowered but distributed over the larger area when the ROA ratio increased, Center of mass position did not change with increasing water mass flow, Increase of the nozzle distance has an small effect on mass distribution of interaction area but distributed over the larger area. It was also conformed that the effect of interaction near central point of collision decreased with the increase of the ROA ratio on interaction area from comparison using superposition method

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.267-270
• /
• 2007

오존무 분사장치는 흡입구와 내에 소정의 공간이 형성된 케이스와 자동 손잡이와 $360^{\circ}$회전이 가능해 운반 및 이동이 간편한 케이스, 상기 케이스의 내부 소정 부위에 공기 흡입구로 흡입되는 공기 중에 포함된 먼지 및 습기를 제거하는 제습 장치와, 원료가스인 공기를 일정하게 제공하는 송풍기, 강력한 살균 소독기능을 지닌 오존발생기, 오존을 발생시키기 위한 고주파 펄스 전원장치, 입자경이 $3{\sim}40{\mu}m$이하의 이류체 미세 분사형 노즐, 살수통(물을 담는 용기) 및 기능 조절부(펄스전원제어, 타이머 조절, 송풍기 제어, 이류체 미세 분사형 노즐스위치 제어)로 성되어 작동하는 것으로 일반적인 가습기와는 다르다. 그리고 강력한 살균, 소독, 탈취 및 대기의 정화 기능이 있는 오존을 이용하는 동시에 기존의 방식보다 간단한 구조의 분무발생 수단을 구비함으로써 전체적으로 구성을 간단하게 하면서 대기 정화 효율을 향상시키는 장점이 있다.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.1-9
• /
• 1993

디젤 엔진의 연소 과정에서 흡입공기와 분사된 연료의 최적 혼합기 형성이 배기성분, 연료효율 등 엔진의 성능을 향상시키는데 있어 매우 중요한 과제중의 하나이다. 이를 위하여 연료분무 현상에 대한 연구와 더불어 연소실내 공기유동 현상에 대한 연구가 주요 관심대상이 되어왔다. LDV를 이용한 3-D 유속측정 및 각종 CFD Code를 이용한 유동해석등의 방법으로 엔진 실린더 내부의 유동현상을 이해하는데 많은 도움이 되고 있으나 아직도 엔진연소실설계 등 엔진 개발에 있어서는 종래의 방법에 의한 실린더내 와류 강도의 비교평가에 크게 의존하고 있으므로 여기서는 디젤 엔진의 와류를 측정 평가하는 방법으로 Paddle Wheel회전을 이용한 Paddle Wheel식 Swirl Meter방식과 실린더내 흡입공기의 각 운동량을 측정하는 Impulse식 Swirl Meter 방식에 대해 고찰하고자 한다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.59-70
• /
• 2021

An experimental study was conducted to observe the spray characteristics for different flow rates and rotating speeds of a rotating fuel nozzle of a slinger combustor. The water spray ejected from the nozzle orifice was visualized using a high-speed camera and a light source. It was confirmed that the atomization was improved, as the flow rate decreased and rotating speed increased. The characteristic maps for the spray characteristics and performance parameters showed that the aerodynamic Weber number and the liquid-air momentum flux ratio were associated with the liquid primary breakup, and the liquid-air momentum flux ratio and Rossby number were closely correlated with the liquid ejection mode.

• Journal of agriculture & life science
• /
• v.46 no.3
• /
• pp.119-127
• /
• 2012

For the promotion of the evaporative cooling efficiency of hot air in greenhouse in summer, a fog sprayer consisted of a high volume spraying two-fluid nozzle with turbo fan and a blowing fan was set up at 2.2 m height from bottom of small glass greenhouse and tested to estimate the possibility of the greenhouse cooling. The mean droplet size and the volume sprayed by one of fog sprayer were $29{\mu}m$ and $160m{\ell}/min$. All the droplets sprayed and blown by the fog sprayer were evaporated within 2 m radius. The result from the cooling test that two sprayers set up in glass greenhouse of plane area $228m^2$ was represented lower cooling effect that the temperature and relative humidity of inside air of greenhouse were $28.8^{\circ}C$ and 87.5% when those of outside air of greenhouse were $30.2^{\circ}C$ and 81.2%. Through investigation of literatures and results of the cooling test, it was estimated that the water spraying rate of evaporative cooling of single span greenhouse with 50% light curtain and with air change rate of 1 volume/min was $10m{\ell}/min/m^2$ so that the inside air temperature may cool down $2{\sim}3^{\circ}C$ on the basis of $35^{\circ}C$ atmospheric temperature in summer of south korean area.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.251-262
• /
• 1995

The goal of this study is to provide fundamental information on the design of a new diesel injector system. The cylindrical disk spray was made by an impinging disk insited below the exit of air-assist atomizor. The disintegration processes on a twin-fluid atomization by air-assist atomizor were investigated. Liquid jet was disintegrated at the condition that wavelength was equal and longer than the circumference of the liquid jet, .lambda. .geq. .pi.do. However, the wavelength and the diameter of the liquid jet were decreased according to the increasing of air velocity. The relative density distribution of droplets and pattern of spray by impinging disk were investigated with a C-CCD. Optimum design conditions for cylindrical disk spray were also achieved. The pattern of cylindrical spray can classified according to the size of the disk and the distance from the nozzle tip to the disk. When the space of the disk and the nozzle tip was narrow and the diameter of the disk was larger than that of the air orifice of the nozzle exit, the good distribution of spray could be achieved. When the air flowrate was constant, the spray width was decreased according to the increasing of the liquid flowrate. When the liquid flowrate was constant, the spray width was decreased according to the increasing of the air flowrate.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.214-219
• /
• 1998

The transparent conducting tin oxide films were deposited on g1ass substrates by the ultrasonic spray pyrolysis. Examined were effects of deposition parameters on the electrical resistance, optical transmittance, crystal structure, and thickness of tin oxide films. As both the deposition time and concentration of tin(IV) chloride increase, the deposited tin oxide films exhibited the decrease of electrical resistance and optical transmittance in the visible and near infrared region. With increasing heat-treatment temperature in air, the deposited tin oxide films showed the enhanced electrical resistance and optical transmittance. This study suggests that the ultrasonic spray pyrolysis may be a promising deposition technique effectively to prepare transparent conducting films of good quality in a single step.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.242-246
• /
• 2004

Nano-sized a-alumina with a narrow distribution was prepared by using Flame Spray Pyrolysis (FSP). The microemulsion of water in oil (W/O) was prepared to make ultrafine droplets for FSP process. Kerosene (fuel) as a continuos phase and Al(NO$_3$)$_3$$.$9$H_2O$ (oxidizer) aqueous solution as a dispersed phase were prepared for microemulsification. The microemulsion with dispersion stability was obtained by adjusting the composition of 80 vol% kerosene, 10 vol% aqueous solution, and 10 vol% emulsifying agent. Microemulsion was sprayed onto the flame by using two-fluid nozzle spray gun under the condition of 0.03 ㎫ air pressure. The synthesized products were $\alpha$-alumina phase with the size of 20 to 30 nm.

• Journal of ILASS-Korea
• /
• v.20 no.2
• /
• pp.70-75
• /
• 2015

Swirl flow in the gun type burner has an impact on the stabilization of the flame, improvement of the combustion efficiency. The swirl flow is created by the spinner which is inside the airtube that guide the combustion air. Gun type burner has generally the inner devices composed electronic spark plug, injection nozzle, combustion device adaptor, and spinner. These inner components change the air flow behavior passing through airtube. So, this study conducted the measurement using by hot-wire anemometer and analyzed effect of the swirl number of spinner on the exhaust air of gun type burner. Turbulence characteristics come up in this study was mean velocity, turbulence intensity, kinetic energy, shear stress and flattness factor of the air flow with the change of the distance of axial direction and tangential direction from the exit of the airtube.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.12
• /
• pp.3352-3359
• /
• 1995

An Eulerian-Lagrangian method is employed to simulate the ignition process and the flame propagation through the air/fuel spray mixture in a closed constant-volume combustor. The spray mixture is ignited by providing a hot wall at the end of the combustor or by firing the electric spark. The investigated parameters involve the initial droplet size, overall equivalence ratio, initial fuel vapor concentration, distance between the hot wall and the nearest droplet, and the ignition energy. Numerical results clearly show the existence of the optimum spray condition for minimizing the ignition energy and the ignition delay time as well as the critical dependence of ignition upon the distance of the heat source to the nearest droplet.