• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.12
• /
• pp.929-936
• /
• 2013

The saturator and injection nozzle are important facilities on the dissolved air flotation process. To increase the formation of micro bubble, it is required to improve the air dissolving performance in the saturator and keep the pressure uniform from the saturator to the nozzle. This study aimed to evaluate the performance of the saturator and the hydraulic effect of the nozzle and the pipe structure. The air volume concentration, bubble size and bubble residual time were measured in the test. The saturator, which had mounted with the spray nozzle, showed a good performance for bubble formation. Also, the characteristics of micro bubble formation were influenced by pressure uniformity and flow velocity through the orifice in the nozzle.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2003.11a
• /
• pp.71-73
• /
• 2003

본 연구에서는 안정 상태에서 일반 공기 중에 산소 농도(21％) 환경에 비해 외부에서 고 농도(35％)의 산소 공급이 혈중 산소 포화도(SPO2), 심박동율(Heart rate), 피부전도도(Galvanic skin response)에 어떠한 영향을 미치는지를 검증하고자 한다. 35％의 고농도 산소를 2L/min의 양으로 일정하게 공급할 수 있는 산소 공급 장치를 이용하였고, 뇌 질병이 없는 5명의 대학생들이 피험자로 참여하였다. 21％의 비해 35％ 산소 농도에서 모든 실험 참여자의 3분 동안의 평균 심박동율은 감소하였고 평균 혈중 산소 포화도는 증가하였다. 그러나 피부전도도는 차이가 없었다.

• The Journal of Engineering Geology
• /
• v.32 no.2
• /
• pp.209-219
• /
• 2022

To experimentally investigate the variation of soil characteristics in slope during rainfall and the shape of slope failure, the model test was performed using soil box and artificial rainfall simulator. The model test of slope formed by the homogenous sand was performed, and the saturation pattern in the model slope due to rainfall infiltration was observed. The slope model with the inclination of 35° was set up on the slope of 30°, and the rainfall intensity of 50 mm/hr was applied in the test. The soil depth of 35 cm was selected by considering the size of soil box, and the TDR (time domain reflectometry) sensors were installed at various depths to investigate the change of soil characteristics with time. As the result of model test, the slope model during rainfall was saturated from the soil surface to the subsurface, and from the toe part to the crest part due to rainfall infiltration. That is, the toe part of slope was firstly saturated by rainfall infiltration, and then due to continuous rainfall the saturation range was enlarged from the toe part to the crest part in the slope model. The failure of slope model was started at the toe part of slope and then enlarged to the crest part, which is called as the retrogressive failure. At the end of slope failure, the collapsed area increased rapidly. Also, the mode of slope failure was rotational. Meanwhile, the slope failure was occurred when the matric suction in the slope was reached to the air entry value (AEV) estimated in soil-water characteristic curve (SWCC).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.300-300
• /
• 2004

본 연구에서는 언어과제 수행 시 일반 공기 중의 산소 농도 (21%) 환경에 비해 외부에서 고 농도 (30%)의 산소 공급이 혈중 산소 포화도(SPO$_2$), 심박동율(Heart Rate), 정답률(Accuracy), 반응속도(Reaction Time)에 어떠한 영향을 미치는지를 검증하고자 한다. 30%와 21%의 산소를 8L/min의 양으로 일정하게 공급할 수 있는 산소 공급 장치를 이용하였고, 10명의 대학생(오른손잡이, 평균나이 23.4세)을 대상으로 실험을 수행하였다. 난이도가 비슷한 두 가지 언어과제를 28문제씩 피험자에게 풀게하여 정답률과 반응속도를 계산하였다.(중략)

• Journal of Soil and Groundwater Environment
• /
• v.11 no.4
• /
• pp.10-17
• /
• 2006

Laboratory-scale two-dimensional aquifer physical model studies were conducted to assess the effect of air injection rate and air injection pattern on the removal of disel contaminated soil and groundwater by air/bio-sparging. The experimental results were represented that the optimal conditions in this experiment were as air injection rate of 1,000 ml/min and pulsed air injection pattern(15 min on/off). The results of the TPH reduction, DO consumption and $CO_2$ production indicate the effective biodegradation evidence of diesel. Based on our results, The minimal $O_2$ supply and pulsed air injection pattern could effectively enhance the diesel removal and the pulsing air injection had effect on oxygenation in this system. Thus, the cost of operating air/bio-sparging system will be reduced if optimal air injection rate and pulsed air injection pattern are applied to remediate contaminants.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.232-232
• /
• 2011

DAF는 기존 침전 공정에 비해 뛰어난 정수 품질과 빠른 처리 시간으로 차세대 정수 공정으로 각광 받고 있다. DAF는 기포 생성 방법에 따라 용존 공기 부상법, 분산 공기 부상법, 진공 부상법, 전해 부상법, 미생물학적 부상법 등이 있다. 이 중 가장 많이 쓰이는 방식은 용존 공기 부상법으로, 과포화 상태의 기체와 액체의 혼합액을 압력을 급격히 감소시켜 기포를 발생 시키는 방법이다. 이 방법은 기포의 발생은 많지만 장비의 크기가 거대하고 시설제조 비용이 많이 드는 단점이 있다. 수중에서 발생되는 플라즈마는 그 구조와 메카니즘에 따라 생성되는 버블의 양을 제어할 수 있음을 확인하였다. 모세관 형태의 전극을 이용한 수중 방전은 전원 공급 장치만 있다면 적은 공간으로도 효과적으로 기포를 생성 할 수 있기 때문에, 수중 방전을 이용하여 기포 발생 후 DAF에 적용 가능한지 알아보고자 한다. DAF공정에서 필요한 요인으로는 기포의 크기, 개수, 성분 물질 등이 있는데, 그 중 가장 핵심은 기포의 크기 이다. 그래서 간단한 전원 장치와 리액터 제작 후 방전에 최적화 된 전극으로 기포를 발생시켜 기포의 크기를 측정하였다. 기포의 크기는 전극의 직경과 방전공간의 비율에 따라 제어가 가능함을 확인하였고 평균 기포의 크기는 약 50 ${\mu}m$로서, DAF에 적용 할 수 있는 크기이다. 일반적으로 기포의 사이즈가 작을수록 입자 제거율이 높은데, 실제 DAF공정에서 사용되는 기포의 사이즈는 80 ${\mu}m$정도 이다. 따라서 개발된 기포 발생장치를 DAF 공정에 응용한다면 높은 효율을 가질 것으로 판단된다.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.29 no.3
• /
• pp.5-16
• /
• 2021

In this study, the applicability of the MBR(Membrane Bio Reactor) process of oxygen dissolve was evaluated through comparison and evaluation of the efficiency of oxygen dissolve device and conventional aeration device in the explosive tank within the MBR process. The organic matter and ammonia oxidation by oxygen dissolve device were evaluated, and the efficiency of persaturation was evaluated by applying real waste water (anaerobic digester effluent treatement from food waste). SCOD and ammonia removal rates for oxygen dissolve device and conventional aeration device methods were similar. However, it was determined that the excess sludge treatment cost could be reduced as the yield of microorganisms by oxygen dissolve device is about 0.03 g MLSS-produced/g SCOD-removed lower than that of microorganisms by conventional aeration device. The removal rates of high concentrations of organic matter (4,000 mg/L) and ammonia (1,400 mg/L) in anaerobic digester effluent treatment from food waste were compared to the conventional aeration device and the oxygen dissolve device organic matter removal rate was approximately 13% higher than that of the conventional aeration device. In addition, for MLSS, the conventional aeration device was 0.3 times higher than for oxygen dissolve device. This is believed to be due to the high progress of sludge autooxidation because the dissolved oxygen is sufficiently maintained and supplied in the explosive tank for oxygen dissolve device. Therefore, it was determined that the use of oxygen dissolve device will be more economical than conventional aeration device as a way to treat wastewater containing high concentrations of organic matter.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.5-7
• /
• 1974

1. This study indicates that above the fiber saturation point the drying rate can be increased with increasing the velocity of the air circutation, i.e., the drying rate of sample boards is proportional to the air velocity, but below the fiber saturation point, the effect of the velocity of air circulation is very low as shown in Figs. 1 and 2. 2. Under the controlled temperature and humidity in the kiln, the more the sample boards have moisture, the higher drying rate of it can be obtained. In other words, this means that even though in the case of drying various moisture content of wood, at the final drying stage, approximately the same percentage of moisture content of wood can be secured by employing the higher velocity of air circulation. 3. This study shows that the rate of drying in kiln changes distinctly at the fiber saturation point, i, e., above the fiber saturation point, the drying curve shows concave aginst the X axsis, but below the fiber saturation point, in the range from 30 percent of moisture content to 20 percent of moisture content, the curve shows convex as shown in Fig. 3. As the drying progresses, however, the drying curve shows concave again below 20 percent of moisture content. This means that inflection point of drying curve may be located clearly at the fiber saturation point, i.e., 30 percent of moisture content. As mentioned above, the 30 percent of moisture content of wood at which the inflectional point appears can be recognized as a critical point, i. e., the fiber saturation point at which all free water was removed from wood. The existence of inflectional point indicates that the evaporation of hygroscopic water in a cell wall is more difficult than the evaporation of free water in a cell cavity and the minor space of cell wall. The convex curve in the range of moisture content from 30 percent to 20 percent means that the evaporation of capillary condensed water has a tendency of the same rates of drying approximately, but as approaching to the 20 percent of moisture, the transfusion of moisture from wood becomes difficult because of having less moisture in cell wall. Below 20 percent of moisture content, the drying curve shows concave again, which means that it is difficult to remove the moisture located nearer to the surface of cellulose molecules and the surface bound water. These relations were revealed in Fig. 4. In comparison AC curve which does not have the two inflection points with BD curve which has two inflection points, i.e., Band D, they are mentioned already, by existence of the inflection points, the curve BD shows that the change of drying rate in the interval from 20 percent of moisture content to 30 percent of moisture content is not greater than in the case of the curve AC in the same interval. At the inflection point of 30 percent of moisture content, it can be noticed that the changing of the drying rate is very conspicuous. This phenomenon also can be recognized, as it is noticed by the Fig. 3, the drying rate from green to 30 percent of moisture content is very great. But the inclination of the curve is very slow from 30 percent of moisture content to 20 percent of moisture content, i.e., the inclination of the curve becomes almost horizontal lines. Acknowledgments Gratitude is expressed to Fred E. Dickinson, Professor of 'Wood Technology, School of Natural Resources, University of Michigan, USA for his suggestion to carry out this study.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.124-129
• /
• 1998

고온고압 수화학 분위기를 모사한 조건에서 피로균열성장 거동에 관한 연구를 수행하였다. 고온고압분위기 모사를 위해 Load machaine, Autoclave, Water loop, 균열측정장치(Reversing DCPD) 그리고 전기화학변수 측정장치 등을 설치하였다. 우선 공기분위기 및 상온수화학 분위기에서의 시험을 통해 안정성을 확인하였으며, 안정한 조건에서 고온수화학분위기에서 실험을 수행하였다. 수화학 분위기에서 용존산소에 상관없이 취성파면이 관찰되었다. 용존산소의 양이 적을 경우(10ppb이하) 발견된 취성파면의 양은 연성파면에 비해 훨씬 적었으며, 용존산소가 높을 경우(8000ppb) 취성파면의 양이 많이 발견되었다. 산소포화된 고온수화학 분위기 피로시험결과는 피로균열성장이 주로 취성파면에 의해 이루어졌으며, 균열성장속도 또한 크게 증가하였다.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 1997.05a
• /
• pp.17-22
• /
• 1997

본 연구에서는 고구마 조직배양묘의 $CO_2$ 교환량을 측정하기위해 개방형 광합성측정장치의 원리를 이용해 자체제작한 $CO_2$ 교환량 측정장치를 이용하여 공기 주입구와 배출구의 $CO_2$ 농도를 연속측정하고, 명기와 암기에 있어서의 $CO_2$ 교환량의 일변화를 분석했다. 내용적 1.48$\ell$의 배양기에 32개의 식물체를 이식했을 때 식물체당 일일 $CO_2$ 교환량은 19일째에 포화에 달했다. 식물체 생장에 있어서는 자연환기구보다 강제환기구의 생장이 촉진되었고, 강제환기구에서는 $CO_2$ 시용구가 무시용구보다 생장이 촉진되었다. 본 연구의 결과는 고구마 조직배양묘를 강제환기와 $CO_2$ 시용등 배양환경의 개선함으로써 순환과정을 거치지 않고 포장정식이 가능한 배양묘나 삽수의 생산이 가능함을 시사한다고 사료된다.