• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.4
• /
• pp.344-349
• /
• 2009

To improve performance of the main landing gear for helicopters, a semi-active control landing gear is introduced in this paper. An MR damper based on commercial finite element electromagnetic field analysis of an electromagnet has been adapted the shock absorber. Force control algorithm (which maintains constantly the sum of air spring force and damping force as internal forces) which keep the sum of air spring force and damping force constant during landing, has been used for the controller, applied to control the semi-active landing gear. A series of drop simulations using ADAMS has been done with the passive, sky-hook control type, and force control type landing gears. The result of each simulation has been compared to evaluate the landing performance of the proposed force control type landing gear.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.5
• /
• pp.860-867
• /
• 2009

In this paper, we designed the array antenna for FMCW radar in X - band frequency, and we chose stacked structure for improvement of narrow bandwidth. The array antenna is implemented on the circuit board which is relative permittivity 2.33 and the stacked patchs are designed on the circuit board which is relative permittivity 4.6. A Foam which has a similar permittivity of air is added to keep the particular gap between array antenna and the stacked patch. The result of array antenna has characteristics that a half-power beam width is $10.6^{\circ}$ and antenna gain is 18.70 dBi and bandwidth is 1.25GHz at the design frequency of 9GHz. The result of the array antenna with the stacked structure has that the half power beam width is $15.17^{\circ}$ and the antenna gain is 15.85dBi and bandwidth is 2GHz. It is needed to improve the antenna gain as keeping bandwidth in same level.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.3
• /
• pp.131-137
• /
• 2017

In order to safely protect high over current flowing into the main circuit at short-circuit without any explosion or fire, the enclosed cartridge fuse with a high interrupting capacity should be applied. But this fuse is impossible to be applied to an inner electronic circuit because of a limited space problem result from the miniaturization trend of products. Therefore, it is necessary to apply a sub-miniature fuse with a relatively small size. However the semi-enclosed fuse which is more free for an influx of air than the enclosed cartridge fuse and is possible to protect fuse elements with chemical and physical combination can be adoptable. But it has a limit of implementing the characteristic of a high breaking capacity. For these reasons, the Fe-42wt％Ni fuse elements alloy and fuse-link with less space were designed to increase a breaking capacity of sub-miniature fuse and its safety for fire and explosion was confirmed in this paper.

• Journal of Welding and Joining
• /
• v.12 no.2
• /
• pp.11-19
• /
• 1994

레이저 가공기술은 재료가공 분야에서 넓은 응용분야를 가지고 있으며, 특히 절단, 용접, 열처리 등의 가공분야에서 고정밀도와 자동화의 용이성으로 인해 생산성이 높은, 고부가가치의 첨단응용 기술로 부각되고 있다. 특히 레이저절단은 타 절단법에 비교되는 절단정도, 열영향, 생산성, 작업 환경등의 각종 우위성으로 박판 및 후판절단분야에서 급속한 보급을 보이기 시작하였다. 현재 대 부분의 레이저 가공기는 CNC화 되어가고 있는 추세이며, 레이저 절단의 경우 생산성증대 및 고 정밀화를 위하여 CAD/CAM인터페이스에 의한 자동화가 필연적인 상황이다. 뿐만아니라 고출력 레이저 발전기를 가공 기본체에 탑재한 탑재형 레이저가공기의 출현으로 대형부재의 절단이 가능 하게 되었으며, 더불어 절단공정의 무인화를 지향하는 각종 시스템이 개발되고 있다. 이와 같은 무인화, 생산성증대, 작업시간단축과 러닝 코스트 및 재료의 절감을 위한 노력의 일환으로 컴 퓨터에 의한 자동 및 반자동 네스팅 시스템의 개발을 들 수 있다. 레이저에 의한 2차원 절단응 용분야에서의 네스팅작업은 설계가 끝난 각 부품의 절단작업의 전단계로서 수행되며, 일반적으로 네스팅공정이 완료되면 절단경로를 결정하고 가공조건과 함께 수치제어공작기계의 제어에 필요한 NC코드를 생성하게 된다. 최근에는 이와 같은 네스팅 시스템이 일부 생산현장에 적용되고 있 으나 이러한 시스템들의 대부분이 외국에서 개발된 것을 수입하여 사용하는 실정이다. 2차원 패턴의 최적자동배치문제는 비단 레이저 절단과 같은 열가공 분야에서 뿐만 아니라 블랭킹 금형, 의류, 유리, 목재등 여러분야에서 응용이 가능하며 패키지의 국산화가 시급한 실정이다. 네스 팅작업은 적용되는 분야에 따라 요구사항과 구속조건이 달라지며 이로 인해 알고리즘과 자료구 조도 달라지게 되나 공통적인 목표는 주어진 영역안에서 겹침없이 배치하면서 버림율을 최소화 하는 것이다. 지난 10여년간 여러 산업의 응용분야에서는 네스팅시스템의 도입이 활발하게 이 루어지고 있는데 수동에 반자동 및 자동에 이르기까지 다양하나 자동네스팅시스템의 경우 배치 효율의 신뢰성이 비교적 부족하기 때문에 아직까지는 생산현장에서 기피하는 실정이다. 배치알 고리즘의 관점에서 볼 때 이러한 문제들은 NP-complete문제로 분류하며 제한된 시간안에 최적의 해를 구하기가 가능한 조합 최적화 문제로 알려져 있다. 따라서 이 글에서는 레이저 절단분야 에서의 네스팅시스템에 관한 개요와 최근의 연구동향 그리고 몇 가지 전형적인 네스팅 알고리 즘들을 소개하고 비교분석을 통해 개선점을 간략하게 논의하고자 한다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.2
• /
• pp.83-96
• /
• 2011

Currently, the commonly used tunneling method in Korea is NATM (New Austrian Tunneling Method). This method uses the rock bolt, shotcrete, and supporting system to maintain the strength of original soil and ensures the stability of tunnel by stabilizing the soil using the original strength of the soil in maximum after the excavation. In past years, wire-mesh reinforced shotcrete was common ones but currently steel-fiber reinforced shotcrete is being widely used for the tunnel construction site in Korea to save construction time with the advanced construction technology. The results further indicate that needs for the establishment of not only the specifications for shotcrete but the strengthening methods for the under reinforced shotcrete sections. Therefore, this study deals with the development of a new steel-fiber to ensure the stability of tunnels that are under reinforced with steel-fibers and to overcome the shortcomings of conventional method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.1
• /
• pp.69-75
• /
• 2009

This paper studies the aerodynamic performance that the vent mixer-new conceptual supersonic mixer-showed with its geometric characteristics. The hole is 2 mm with 2 mm's distance from the wall in case 1 and with no distance in case 2. In case 3 die hole is 1 mm. Case 1 and case 2 showed the same total pressure recovery ratio, of which the case 3 was lower than that. While cases 1-3 had the same reattachment length, the shear layer was thicker in cases 1 and 2 than in case 3. Within the recirculation zone, cases 1 and 2 had lower pressure loss and higher velocity gradient difference than case 3-they enhance mixing between air and fuel. Separation bubble which is developed by the inflow into the recirculation zone has a significant effect on the total pressure recovery ratio in the combustor. Also separation bubble influences pressure distributions and recirculation flows in the recirculation zone. Therefore, inflow rate of air into the recirculation zone mainly affects the performance of vent mixer.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.37-40
• /
• 2008

Recently, Construction Business, is changing very quickly, exceedingly needs to slim down the construction expensive by reducing material costs and the term of works. The term of formwork takes 25% of the term of works and costs 15% to 20% of the cost of construction. Hereupon, the purpose of this study is to investigate the Axial Strength of Centrifugall Formed Shell PC Columns that can reduce the term of formwork, the costs of material, the difficulty of throwing away the waste. Shell PC Column is loaded stirrups and manufactured at factory, so it has good points like construction's quality control and part's precision. However, it needs to be tested for checking bonded ability because it is set up at core and coverd with concrete. therefore this study is necessary three type of columns, which are a RC column, different type of two compressive strength core concrete columns and a Shell PC Column. By three columns, this study compare with and analysis three columns's bonded and Compressive Behavior abilities.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1264-1271
• /
• 1990

The vortex lattice method was adopted to predict the aerodynamic performance of a horizontal axis wind turbine. For this simulation. the rotor blade was divided into many panels both in chordwise and spanwise direction and then replaced by horseshoe vortices. The wake was divided into two parts of near wake and far wake : the near wake was assumed as helical vortex line elements and the far wake was modeled by semi-infinite circular vortex cylinder. The induced velocity components were calculated by the Biot-Savart law. By this way the power coefficient was obtained and represented as a function of the tip speed ratio. The numerical results obtained were compared with those of the other methods and experimental results and showed good agreement with experimental results.

• Journal of Advanced Navigation Technology
• /
• v.27 no.1
• /
• pp.96-101
• /
• 2023

In this work, an energy harvester (EH) on the rotating shaft has been proposed for a wireless sensor system (WSS) applications. The EH was designed and implemented to the shaft with a diameter of 20 cm to continuously power a wireless sensor system (WSS). The rotor has coils wound in pairs on seven U-shaped cores attached to the shaft. The stator consists of eight pairs of magnets attached to eight I-cores and they are fixed to an outer fixture. The generated power of the EH was investigated as function of the air gap between the rotor and stator, the number of turn of coils, and shaft speed. The fabricated EH produced power up to 2.87 W at 300 rpm and the 3 mm air gap.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.4
• /
• pp.121-125
• /
• 2023

In winter, Jeju's Seogwipo and Jungmun areas are 2~3℃ warmer than Jeju City. The reason is that when the north wind over Halla Mountain crosses Baengnokdam of Halla Mountain and passes the 300m long and 260m vertical rock face of Donnaeko at an altitude of 1600m above sea level, the cold air turns into warm air through adiabatic compression, and the warmth rides on Donnaeko and flies to Seogwipo and Jungmun. Conversely, the south wind that rises over the sea in Seogwipo in the summer passes over Hallasan Mountain and passes 99 valleys before turning into a muggy, humid climate, making Jeju hot. In other words, it is because of The wind from Jeju City to Seogwipo-The Wind from Seogwipo to Jeju City.