• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.9
• /
• pp.929-936
• /
• 2015

Nacelle anemometers are mounted on wind-turbine nacelles behind blade roots to measure the free-stream wind speed projected onto the wind turbine for control purposes. However, nacelle anemometers measure the transformed wind speed that is due to the wake effect caused by the blades' rotation and the nacelle geometry, etc. In this paper, we derive the Nacelle Transfer Function (NTF) to calibrate the nacelle wind speed to the free-stream wind speed, as required to carry out the performance test of wind turbines according to the IEC 61400-12-2 Wind-Turbine Standard. For the reference free-stream wind data, we use the Light Detection And Ranging (LiDAR) measurement at the Shinan wind power plant located on the Bigeumdo Island shoreline. To improve the simple linear regression NTF, we derive the multiple nonlinear regression NTF. The standard error of the wind speed was found to have decreased by a factor of 9.4, whereas the mean of the power-output residual distribution decreased by 6.5 when the 2-parameter NTF was used instead of the 1-parameter NTF.

• The korean journal of orthodontics
• /
• v.36 no.5
• /
• pp.349-359
• /
• 2006

Objective: Nickel-titanium alloy wire possesses excellent spring-back properties, shape memory and super-elasticity. In order to adapt this wire to clinical use, it is necessary to bend as well as to control its super-elastic force. The purpose of this study is to evaluate the effects of heat treatment on the load-deflection properties and transitional temperature range (TTR) of nickel-titanium wires. Methods: Nickel-titanium wires of different diameters ($0.016"\;{\times}\;0.022"$, $0.018"\;{\times}\;0.025"$ and $0.0215"\;{\times}\;0.028"$) were used. The samples were divided into 4 groups as follows: group 4, posterior segment of archwire (24 mm) without heat treatment; group 2, posterior segment of archwire (24 mm) with heat treatment only; group 3, anterior segment with bending and heat treatment; group 4, anterior segment with bending and 1 sec over heat treatment. Three point bending test was used to evaluate the change in load-deflection curve and obtained DSC (different scanning calorimetry) to check changes in $A_f$ temperature. Results: In the three point bending test, nickel-titanium wires with heat treatment only had higher load-deflection curve and loading and unloading plateau than nickel-titanium wires without heat treatment. Nickel-titanium wires with heat treatment had lower Af temperature than nickel-titanium wires without heat treatment. Nickel-titanium wires with heat treatment and bending had higher load-deflection curve than nickel- titanium wires with heat treatment and nickel-titanium wires without heat treatment. Nickel-titanium with heat treatment of over 1 sec and bending had the highest load-deflection curve. Nickel-titanium wires with heat treatment and bending had lower Af temperature, Nickel-titanium wires with heat treatment of over Af sec and bending had the lowest Af temperature. Conclusion: From the results of this study, it can be stated that heat treatment for bending of Nickel-titanium wires does not deprive the superelastic property but can cause increased force magnitude due to a higher load-deflection curve.

• Journal of Soil and Groundwater Environment
• /
• v.11 no.1
• /
• pp.14-22
• /
• 2006

Laboratory column experiment for simultaneous removal of Cd and Cr(VI) were conducted using newly developed material of Fe-loaded zeolite having both reduction ability and sorption capacity. The solution containing Cd and Cr(VI) was injected into the column and the breakthrough curves (BTCs) for the contaminants were observed at the effluent port. Cd breakthrough was not initialized until Cr(VI) breakthrough was completed. Therefore it could be concluded that overall efficiency of Fe-loaded zeolite should be determined by the reactivity for Cr(VI). The relative concentration of Cr(VI) BTC increased to the unit value while initial breakthrough was delayed and the propagation of breakthrough was slowed. In order to quantitatively describe the shape of Cr(VI) BTC, new parameters of ${\alpha}\;and\;{\beta}$ designated to be shape parameters, were defined and applied in contaminant transport concentration. These parameters were employed to represent the degree of initial breakthrough delay and the degree of breakthrough propagation, respectively. As initial contaminant concentration increased, ${\alpha}$ decreased, which indicated the delay of BTC's initiation. And as initial contaminant flow rate increased, ${\beta}$ decreased, which represented the faster propagation of the BTC. From these results, Fe-loaded zeolite was found to be an effective reactive material for PRBs against heavy metals having different ionic forms in groundwater. And it could be expected that as groundwater flows faster, the propagation of breakthrough would be faster and as contaminant concentration is higher, the initial point of breakthrough would appear earlier.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.230-230
• /
• 2022

최근 기후변화로 인해 예측이 어려운 국지성 호우가 빈번하게 발생하고 있다. 국지성 호우는 대량의 홍수를 일으켜 유송잡물을 동반한 흐름을 야기할 수 있다. 대량의 유송잡물이 하상에 퇴적되면 통수능을 저하시키기도 하며 식생효과와 마찬가지로 유목주변으로 유속이 증가하면서 세굴현상이 발생하게 되는데, 이는 하상저하를 일으키며 수공구조물의 안정성에 지속적으로 피해를 줄 수 있다. 기후변화는 또한 강우패턴을 변화시켜 식생의 성장과 활착에도 영향을 미치게 된다. 본 연구지역인 내성천 회룡포의 경우, 2015년 대가뭄 발생 이후 식생활착으로 인해 식생대 면적이 증가하고 잇는 상황이다. 이는 연구지역의 흐름과 사주교란 및 하상변동에도 큰 영향을 미칠 것으로 판단되며, 특히 식생의 증가는 유송잡물의 증가를 야기 할 수 있기 때문에 식생과 유송잡물의 영향이 하천에 미치는 영향을 예측하는 연구가 필요할 것으로 판단된다. 따라서 본 연구에서는 2차원 흐름모형인 Nays2D와 입자법기반의 유목동역학 모형을 활용하여 식생과 유송잡물이 하상변동에 미치는영향에 대한 수치실험을 수행하고 결과를 분석하였다. 여기서, 식생의 경우, 식생성장모형을 적용하여 시간에 따라 식생이 성장하여 항력이 증가하는 것으로 가정하였으며 유송잡물의 경우, 하상에 퇴적되는 유송잡물의 개수와 면적만큼 항력이 증가하는 것으로 가정하였다. 흐름의 경계 조건은 일반화된 부정류 수문곡선을 입력하였으며 초기 하도의 형상은 일정한 경사를 가지는 평지로 가정하여 부정류에 따라 하상변동이 발생하는 것으로 모의하였다. 시뮬레이션 결과, 유송잡물보다 식생대 번성이 하상변동에 상대적으로 큰 영향을 주는 것으로 나타났으며, 유송잡물의 경우 국부적으로 퇴적 분포되어 그 주변으로 침식을 일으키는 것으로 나타났다. 또한 유송잡물은 하안의 얕은수역에서 주로 퇴적되었다. 본 연구는 만곡부 하상변동에 대해 식생과 유송잡물을 고려하여 예측모의를 수행한 사례로서, 식생과 유송잡물이 흐름과 하상변동에 미치는 영향을 이해하는데 도움이 될 것으로 판단된다. 또한 이는 추후에 식생을 고려하는 하천관리방안을 수립 시, 식생과 유송잡물의 영향을 물리적으로 설명할 수 있는 근거자료로 제시할 수 있을 것으로 보인다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.2A
• /
• pp.401-409
• /
• 2006

This study presents basic information on the mechanical properties and long-term deformations of high-strength steel fiber reinforced concrete(HSFRC). The Influence of steel fiber on modulus of elasticity, compressive, splitting tensile and flexural strength, and drying shrinkage and creep of HSFRC are investigated, and flexural fracture toughness is evaluated. Test results show that Test results show that the effect of steel fibers on the compressive strength is negligible, and the modulus of elasticity of HSFRC increased with the increase of fiber volume fraction. And the effect of fiber volume fraction($V_f$) and aspect ratio($l_f/d_f$) on tensile strength, flexural strength and toughness is extremely prominent. It is observed that the flexural deflection corresponded to ultimate load increased with the increase of $V_f$ and $l_f/d_f$, and due to fiber arresting cracking, the shape of the descending branch of load-deflection tends towards gently. Also, the effect of addition of various amounts of fiber on the creep and shrinkage is obvious. Especially, the effect of adding fibers to high-strength concrete is more pronounced in reducing the drying shrinkage than the creep.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.12 no.3
• /
• pp.2019-2028
• /
• 1970

1. Experiments were made for the efficient plowing method by the 4 wheel tractor, the results are as follow; 1) In case of plowing of inner side of the field, the efficient turning method to be the smallest turning time is the $\Omega$-shaped turning method in the turning distance less than 2r (r is the minimum turning radius of the tractor), and also, it is the U-shaped turning method in the turning distance larger than 2r. 2) 2.5r is most efficient in the unit turning section 'w' on plowing of the inner side of the field. 3) In case of plowing of outer side of the field, intermitted plowing method is efficient in case of W>-0.0345 L + 35.84, and also, semi-followed plowing method is efficient in case of W<-0.0345 L + 35.84. 4) The smaller the width of outer side of outer side of the field 'I' is, the higher is the plowing efficiency, and it is estimated that the minimum value 2r is suitable to 'I' in plowing of inner side and outer side of the field. 2. Study on the correlation between the unit field and plowing efficiencies obtained the following results; 1) plowing efficienies increase generally according as length-width ratio L/W and area A increase. 2) Percent of increase of plowing efficiencies decreases generally according as length-width ratio and area enlarge. 3) The limit that change of T is large owing to L/W is 6 for 20 a, 5 for 30 a, 4 for 50 a, 3 for 80 a, less than 2.5 for 100 a, generally, in L/W-T curve. 4) Rate of change of T-A curve is similar to rate of change of $T=A-\frac{2}{3}$ curve in spite of influence of L/W. 5) In case that length-width ratio is more than 3, effects of increase of 10 a area influenced upon plowing efficiencies are as much as effects of about 5 increase of length width ratio without correlation of size of the field. 6) In case that length-width ratio is 2 to 3, effects of increase of 10 a area influenced upon plowing efficiencies are as much as effects of about 4 to 2 increase of length-width ratio without correlation of size of the field, and the effects decrease according as not only length-width ratio decreases but also area increases, generally.

• Journal of the Microelectronics and Packaging Society
• /
• v.31 no.2
• /
• pp.54-62
• /
• 2024

SICM (Scanning Ion Conductivity Microscopy) is a technique for measuring surface topography in an environment where electrochemical reactions occur, by detecting changes in ion conductivity as a nanopipette tip approaches the sample. This study includes an investigation of the current response curve, known as the approach curve, according to the distance between the tip and the sample. First, a simulation analysis was conducted on the approach curves. Based on the simulation results, then, several measuring experiments were conducted concurrently to analyze the difference between the simulated and measured approach curves. The simulation analysis confirms that the current squeezing effect occurs as the distance between the tip and the sample approaches half the inner radius of the tip. However, through the calculations, the decrease in current density due to the simple reduction in ion channels was found to be much smaller compared to the current squeezing effect measured through actual experiments. This suggests that ion conductivity in nano-scale narrow channels does not simply follow the Nernst-Einstein relationship based on the diffusion coefficients, but also takes into account the fluidic hydrodynamic resistance at the interface created by the tip and the sample. It is expected that SICM can be combined with SECM (Scanning Electrochemical Microscopy) to overcome the limitations of SECM through consecutive measurement of the two techniques, thereby to strengthen the analysis of electrochemical surface reactivity. This could potentially provide groundbreaking help in understanding the local catalytic reactions in electroless plating and the behaviors of organic additives in electroplating for various kinds of patterns used in semiconductor damascene processes and packaging processes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.1
• /
• pp.436-444
• /
• 2013

This article presents the dynamic response of nano-scale plates using the nonlocal continuum theory and higher-order shear deformation theory. The nonlocal elasticity of Eringen has ability to capture the small scale effects and the higher-order shear deformation theory has ability to capture the quadratic variation of shear strain and consequently shear stress through the plate thickness. The solutions of transient dynamic analysis of nano-scale plate are presented using these theories to illustrate the effect of nonlocal theory on dynamic response of the nano-scale plates. The relations between nonlocal and local theories are discussed by numerical results. Also, the effects of nonlocal parameters, aspect ratio, side-to-thickness ratio, size of nano-scale plate and time step on dynamic response are investigated and discussed. The amplitude and cycle increase when nonlocal parameter increase. In order to validate the present solutions, the reference solutions are used and discussed. The theoretical development as well as numerical solutions presented herein should serve as reference for nonlocal theories as applied to the transient dynamic analysis of nano-scale structures.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.11
• /
• pp.5542-5550
• /
• 2012

Third-order shear deformation theory is reformulated using the nonlocal elasticity of Eringen. The equation of equilibrium of the nonlocal elasticity are derived. This theory has ability to capture the both small scale effects and quadratic variation of shear strain through the plate thickness. Navier's method has been used to solve the governing equations for all edges simply supported boundary conditions. Analytical solutions of buckling of nano-scale plates are presented using this theory to illustrate the effect of nonlocal theory on buckling load of the nano-scale plates. The relations between nonlocal third-order and local theories are discussed by numerical results. Further, effects of (i) length (ii) nonlocal parameter, (iii) aspect ratio and (iv) mode number on nondimensional buckling load are studied. In order to validate the present solutions, the reference solutions are used and discussed. The present results of nano-scale plates using the nonlocal theory can provide a useful benchmark to check the accuracy of related numerical solutions.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6C
• /
• pp.321-329
• /
• 2008

In this study, a series of column test as a way in order to make up for the weakness point of the conventional acceleration method were conducted to both propose the suction board drain method and grapes the specific improvement character of this method as a result of a sort of plastic drain board and a phase of vacuum pressure conditions. On this occasion, the study focused on computing the effective factors of the fittest Suction board drain method affected by each condition through confirming the settlement generated during the test, the water content reduction and stress increase effect occurred arising from the test, and the ratio of consolidation related to the improvement period. In accordance with the shape of core and that whether the core is attached to the filter(pocket or adhesion), the castle type of adhesion and the column type of pocket are more efficient than the others as a consequence of the test to find out the improvement effect depending on each drainage such as a castle type, coil type, harmonica type, column type of pocket and a castle of the adhesion. In case of the step suction pressure, the shorter the period of $-0.8\;kg/cm^2$ as a final step of the suction pressure is, the better the improvement is. In addition, the correlation between degree of consolidation per each suction pressure level and duration of application was drawn as a curve and the point of inflection on this curve was provided to determine the duration period to maximize the consolidation.