• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2004년도 동계학술대회 논문집
• /
• pp.14-14
• /
• 2004

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.819-824
• /
• 2001

Mean velocity and Reynolds stress components of the developing turbulent flows in a rotating 90 degree bend with square cross-section were measured by a hot-wire anemometer. Effects of the centrifugal and Coriolis forces generated by the curvature and rotation of bend on the mean motion and turbulence structures are investigated experimentally. Results show that the Coriolis force associated with the rotation of the bend may act both through the mean motion and turbulent structures, thereby changing the pressure fields, mean and turbulent velocities distributions.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.485-490
• /
• 2000

The effect of curvature, rotation, variable cross-section can make very complex flow pattern in turbo-machinery such as Pumps, compressors, turbines, In this study of turbulent flow characteristics rotating $90^{\circ}$ curved duct under a Plane rate of strain condition is computationally analyzed. The objective of this study is to understand the complex turbulent flow phenomena in turbo-machinery passage by analyzing the modeled rotating $90^{\circ}$ curved duct flow. RSM(Reynolds Stress Model) was employed for the turbulence modeling of Reynolds stress in momentum equations proposed by Shin(1995). The three dimensional computational code which adopts RSM for trubulence modeling was newly developed for the generalized curvilinear coordinate.

• 대한기계학회논문집B
• /
• 제23권8호
• /
• pp.1063-1071
• /
• 1999

Fine grid calculations are reported for the developing turbulent flow in a curved duct of square cross-section with a radius of curvature to hydraulic diameter ratio ${\delta}=Rc/D_H=3.357 $ and a bend angle of 720 deg. A sequence of modeling refinements is introduced; the replacement of wall function by a fine mesh across the sublayer and a low Reynolds number algebraic second moment closure up to the near wall sublayer in which the non-linear return to isotropy model and the cubic-quasi-isotropy model for the pressure strain are adopted; and the introduction of a multiple source model for the exact dissipation rate equation. Each refinement is shown to lead to an appreciable improvement in the agreement between measurement and computation.

• 설비공학논문집
• /
• 제19권2호
• /
• pp.191-201
• /
• 2007

It was noted by the several researchers that the voltage outputs in response to a single yawed hot-wire sensor in a flow perpendicular to the axis deviate from the theoretical voltage output by King's law and Jorgensen's relation. This study noticed that the calibration coefficients of original Grande's method are not constant and fairly sensitive to the radial angle (${\alpha}_{R}$). For more accuracy, this study interpolated the parameters of the Grande relation as a function of radial angle and compared velocity components with ones by Jorgensen and original Grande relation in the calibration jet flow. Finally, as a test case, 3-dimensional turbulent flows of the inlet plane of 180 degree bend are measured and compared the velocity components by above three methods and showed the characteristics of the flows.

• 대한기계학회논문집
• /
• 제16권10호
• /
• pp.1971-1978
• /
• 1992

본 연구에서는 원형 파이프에 원추형 디퓨져가 연결된 덕트 내의 유동장에 대 하여 Launder-Sharma의 저 레이놀즈수 k-.epsilon. 난류모델을 이용하여 수치해석을 수행하였 으며, 수치해석 방법으로는 타원형 방법을 사용하였으며, 앞으로 일반적인 단면의 곡 관이나 스크롤 내부 유동 등의 연구 수행을 감안하여 지배방정식을 일반 비직교 좌표 계로 변환하여 계산을 수행하였다.

• 대한기계학회논문집B
• /
• 제22권2호
• /
• pp.139-152
• /
• 1998

In the present study, the flow characteristics of developing laminar oscillatory flows in a square -sectional 180 deg. curved duct are investigated experimentally. The experimental study using air in a square-sectional 180 deg. curved duct is carried out to measure velocity distributions with a data acquisition and LDV (Laser Doppler Velocimetry) processing system. In this system, Rotating Machinery Resolver (RMR) and PHASE program are used to obtain the results of unsteady flows. The major flow characteristics of developing oscillatory flows are found by analyzing velocity curves, mean velocity profiles, time-averaged velocity distribution of secondary flow, wall shear stress distributions, and entrance lengths. In a lower dimensionless angular frequency, the axial velocity distribution of laminar oscillatory flow in a curved duct shows a convex shape in a central part and axial symmetry. The maximum value of wall shear stress in a lower dimensionless angular frequency is located in an outside wall, but according to increasing the dimensionless angular frequency, the maximum of wall shear stress is moved to inner wall. The entrance lengths of laminar oscillatory flows in a square-sectional 180 deg. curved duct is obtained to 90 deg. of bended angle of duct in this experimental conditions.