• The Korean Journal of Mycology
• /
• v.33 no.1
• /
• pp.22-29
• /
• 2005

The main objectives of this research were to study the cultural and nutritional characteristics of Tricholoma matsutake and to establish its liquid culture system. The optimum growth of T. matsutake was observed in HA and TMM agar media. Similarly highest growth was observed in PDB and TMM liquid media. The optimal temperature for the mycelial growth was $25^{\circ}C$. The most suitable carbon source was dextrin among 12 different carbon sources tested. Yeast extract and peptone were best nitrogen sources among 17 different sources tested. The optimum mineral salts were $Fe_{2}(SO_{4})_{3}{\cdot}H_{2}O$ and KCl among 9 different sources tested. Shaking culture gave higher mycelial growth compared to stationary culture. Similarly, optimum medium amount for shaking culture was 100 ml per 250 ml flask. The highest mycelial growth was obtained when $5{\sim}7$ mycelial discs were inoculated in 100 ml of medium and incubated for $8{\sim}9$ weeks, respectively. The highest proportion of mycelial growth was observed at 40 : 1 ratio of medium to inoculum volume in 8 l air-lift fermenter.

• Korean Journal of Food Science and Technology
• /
• v.7 no.4
• /
• pp.243-249
• /
• 1975

This experiment were carried out to investigate the conditions of amylase produced by Candida muscorum in wheat bran cultures and the properties of its amylase (crude enzyme). The results obtained were as follows. 1. The optimum conditions for amylase production in wheat bran cultures were; water content 75 percent, temperature $25^{\circ}C$ and incubation time 4-7 days. 2. The production of amylase was increased about 20 percent in the medium added 0.5 percent of ammonium sulfate or ammonium chloride to wheat bran, but the production of those was decreased in the case of addition of nitrates. 3. No significant effect was found in the case of the addition of carbon source on the production of amylase. 4. The properties of liquefying amylase of the selected strain were; the optimum pH 4.2, the optimum temperature $60-65^{\circ}C$, the stable pH 3.2-6.8 and the stable heating (for 15 minutes heating) below $65^{\circ}C$. 5. The properties of saccharifying amylase of the selected strain were; the optimum pH 4.5, the optimum temperature $55^{\circ}C$, the stable pH 3.8-6.2 and the stable heating (for 15 minutes heating) below $45^{\circ}C$.

• Journal of the Korean Geosynthetics Society
• /
• v.21 no.2
• /
• pp.57-65
• /
• 2022

This study simulated the shock wave propagation through the tamping material between explosives and hole wall at blasting works and verified the effect of tamping materials. The Arbitrary Lagrangian-Eulerian(ALE) method was selected to model the mixture of solid (Lagrangian) and fluid (Eulerian). The time series analysis was carried out during blasting process time. Explosives and tamping materials (air or water) were modeled with finite element mesh and the hole wall was assumed as a rigid body that can determine the propagation velocity and shock force hitting the hole wall from starting point (explosives). The numerical simulation results show that the propagation velocity and shock force in case of water were larger than those in case of air. In addition, the real site at blasting work was modeled and simulated. The rock was treated as elasto-plastic material. The results demonstrate that the instantaneous shock force was larger and the demolished block size was smaller in water than in air. On the contrary, the impact in the back side of explosives hole was smaller in water, because considerable amount of shock energy was used to demolish the rock, but the propagation of compression through solid becomes smaller due to the damping effect by rock demolition. Therefore, It can be proven that the water as the tamping media was more profitable than air.

• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.296-301
• /
• 2023

Solid oxide fuel cell has received more attention recently due to the fuel flexibility via internal reforming. Commonly used Ni/YSZ anode, however, can be easily deactivated by carbon coking in hydrocarbon fuels. The carbon deposition problem can minimize by developing alternative perovskite anode. This study is focused on improving conductivity and catalytic activity of the perovskite anode by introducing rGO (reduced graphene oxide). Sr_0.92Y_0.08TiO₃(SYT) anode with perovskite structure was synthesized with 1wt% of rGO. The presence of rGO during anode fabricating process and cell operation is confirmed through XPS and Raman analysis. The maximum power density of rGO/SYT anode improved to 3 times in H₂ and 6 times in CH₄ comparing to that of SYT anode due to the high electrical conductivity and good catalytic activity for CH₄.

• Analytical Science and Technology
• /
• v.10 no.4
• /
• pp.264-273
• /
• 1997

Anodic oxidation reaction was applied to remove trihalomethanes in an aqueous solution. Each component was determined by using solid phase microextraction(SPME) fiber and GC-ECD. Anodic and cathodic compartments were separated in order to protect contaminants and connected by $KNO_3$-agar bridge. The calibration graphs of the 6 THM components were shown good linearlity from a few ppb up to a few hundreds ppb concentration level. Anodes such as platinum(Pt), titanium(Ti). zircornium(Zr), titanium metal coated with iridium(Ti-Ir), and glassy carbon coated with mixed valence ruthenium(mv Ru) were tried to remove the THMs at different potentials. The best result was obtained on the Ti-Ir anode applied 9 volts DC. The electrode could effectively remove almost all the THM components from the stirring solution within about 1.5 hours. The glassy carbon electrode coated with mixed valence ruthenium showed excellent removing effect at the begining, but the maximum removing level was remained at 60% probably due to the destruction of the electrode surface. The concentration of chloroform, however, tends to be increased due to the electrode reaction producing the component at the condition.

• Korean Chemical Engineering Research
• /
• v.52 no.4
• /
• pp.544-552
• /
• 2014

In this study, We have investigated the kinetics on the char-$CO_2$ gasification reaction. Thermogravimetric analysis (TGA) experiments were carried out for char-$CO_2$ catalytic gasification of an Indonesian Roto lignite. $Na_2CO_3$, $K_2CO_3$, $CaCO_3$ and dolomite were selected as catalyst which was physical mixed with coal. The char-$CO_2$ gasification reaction showed rapid an increase of carbon conversion rate at 60 vol% $CO_2$ and 7 wt% $Na_2CO_3$ mixed with coal. At the isothermal conditions range from $750^{\circ}C$ to $900^{\circ}C$, the carbon conversion rates increased as the temperature increased. Three kinetic models for gas-solid reaction including the shrinking core model (SCM), volumetric reaction model (VRM) and modified volumetric reaction model (MVRM) were applied to the experimental data against the measured kinetic data. The gasification kinetics were suitably described by the MVRM model for the Roto lignite. The activation energies for each char mixed with $Na_2CO_3$ and $K_2CO_3$ were found a 67.03~77.09 kJ/mol and 53.14~67.99 kJ/mol.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.11
• /
• pp.927-933
• /
• 2016

In a solid propulsion system, the rocket nozzle is exposed to high temperature combustion gas. Hence, choosing an appropriate material that could demonstrate adequate performance at high temperature is important. As advanced materials, carbon/silicon carbide composites (C/SiC) have been studied with the aim of using them for the rocket nozzle throat. However, when compared with typical structural materials, C/SiC composites are relatively weak in terms of both strength and toughness, owing to their quasi-brittle behavior and oxidation at high temperatures. Therefore, it is important to evaluate the thermal and mechanical properties of this material before using it in this application. This study presents an experimental method to investigate the fracture behavior of C/SiC composite material manufactured using liquid silicon infiltration (LSI) method at elevated temperatures. In particular, the effects of major parameters, such as temperature, loading, oxidation conditions, and fiber direction on strength and fracture characteristics were investigated. Fractography analysis of the fractured specimens was performed using an SEM.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.10
• /
• pp.69-74
• /
• 2017

In this study, cholesteryl 4-n-alkoxybenzoates (Chol-n), with alkyl groups used for controlling the temperature of transition to the liquid crystal phase, were synthesized, and the effects of the length of the alkyl groups on the physical properties of the liquid crystal compounds were investigated. The chemical structures and thermal and liquid crystalline properties of the synthesized compounds were investigated by Fourier transform infrared spectroscopy (FT-IR), proton nuclear magnetic resonance spectroscopy ($^1H$-NMR), differential scanning calorimetry (DSC), and polarizing optical microscopy (POM). The synthesized compounds showed melting transition temperatures ($T_m$) in the range of $103^{\circ}C$ to $143^{\circ}C$ and all of the compounds except Chol-6 exhibited a wide liquid crystal phase temperature range of about $60^{\circ}C$ to $100^{\circ}C$. No correlation between the number of carbon atoms in the molecule and the thermal properties of the compounds was found. All of the synthesized compounds showed an enantiotropic cholesteric phase, which was accompanied by a chiral smectic phase in the compounds Chol-6, Chol-8, Chol-9, and Chol-10. All of the compounds exhibited thermochromism in the liquid crystal state, and their color changed from red to blue as the temperature was increased.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.19 no.1 s.71
• /
• pp.93-103
• /
• 2006

It is absolutely essential that safety assessment of the containment buildings during service life because containment buildings are last barrier to protect radioactive substance due to the accidents. Therefore, this study describes an enhanced degenerated shell finite element(FE) which has been developed for nonlinear FE analysis of reinforced concrete(RC) containment buildings with elasto-plastic material model. For the purpose of the material nonlinear analysis, Drucker-Prager failure criteria is adapted in compression region and material parameters which determine the shape of the failure envelop are derived from biaxial stress tests. Reissner-Mindlin(RM) assumptions are adopted to develop the degenerated shell FE so that transverse shear deformation effects is considered. However, it is found that there are serious defects such as locking phenomena in RM degenerated shell FE since the stiffness matrix has been overestimated in some situations. Therefore, shell formulation is provided in this paper with emphasis on the terms related to the stiffness matrix based on assumed strain method. Finally, the performance of the present shell element to analysis RC containment buildings is tested and demonstrated with several numerical examples. From the numerical tests, the present results show a good agreement with experimental data or other numerical results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.4
• /
• pp.657-666
• /
• 2022

The International Maritime Organization(IMO) recommends the active implementation of national policies on technological development and energy efficiency to reduce Green House Gas (GHG) in the international shipping sector. Such IMO environmental regulation policies have a great impact on the entire shipping sector and are also a heavy burden on ship's owners. The most reasonable way to curb GHG emissions from ships comes down to the development of zero-emission ships. In other words, the development of a fuel cell ship (FCS) driven by an eco-friendly fuel is an alternative that can escape the IMO regulations. Countries in Asia, Northern America, and Europe independently develop and produce PEMFC, and are pursuing international standardization by acquiring approval in principle from an internationally accredited registration authority. Currently, there are three types of fuel cells (FC) that are recommended for ships: a Polymer Electrolyte Membrane Fuel Cell (PEMFC), a Molten Carbonate Fuel Cell (MCFC), and a Solid Oxide Fuel Cell (SOFC). In this study, PEMFC, which is expected to grow continuously in the global FC market, was analyzed domestic and international development trends, specifications, performance, and empirical cases applied to ships. In addition, when applying PEMFC to ships, it was intended to suggest matters to be considered and the development direction.