• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.163.1-163.1
• /
• 2010

MTO 공정을 개발하기 위한 순환유동층 장치에서 고체순환량을 높이기 위해 고체 주입량 및 상승관 유속에 따른 수력학적 특성의 파악에 관한 연구를 수행하였다. 전체 높이 2.6m 직경 0.009m의 상승관을 가진 순환유동층 장치에 대해 고체순환량을 조절하기 위한 비기계적 밸브로 각각 Seal-pot과 L-valve가 장착된 두 장치에 대해 고체순환량 및 체류량을 측정하였다. 고체순환량 및 체류량은 두 장치에서 모두 고체의 주입량이 증가함에 따라 증가하는 모습을 나타내었으며, 상승관의 유속에 따라서는 특정한 유속의 범위 내에서 증가하다가 일정 유속 이후 감소하는 모습을 나타내었다. Seal-pot을 사용한 장치에서는 고체순환량이 최대 $87kg/m^2.s$ 가량의 값을 나타내었으나 L-valve를 사용한 장치에서는 최대 $180kg/m^2.s$를 보였다. 이러한 실험 결과를 바탕으로 하여 전산유체역학을 이용한 순환유동층의 유동해석에 관한 연구를 실시하여 실험조건의 변화에 따른 상승관 내부의 수력학적 특성을 비교하였다.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.527-532
• /
• 2016

The effects of gas velocity and solid circulation rate on the axial solid holdup distribution have been determined in a 10 mm-I.D. ${\times}$ 800 mm-high circulating fluidized bed plasma reactor under reduced pressure (1torr). Polystyrene polymer powder and nitrogen gas are used as solid and gas materials respectively. The change of solid circulation rate by a large gas flow rate of the riser (40~80 sccm) is also possible by a relatively small gas flow rate of the solid recirculation part (6.6~9.9 sccm). The solid circulation rate in the reactor under reduced pressure increases with increasing aeration velocity in the solid recirculation part. The axial solid holdup in the riser decreases from the dense at the bottom to the dilute phase at the top section of the riser. Solid holdups at the axial positions in the riser increase linearly with increasing solid circulating velocity. From these results, we could determine the position of plasma load for good plasma ignition, maintain and plasma reaction.

• Journal of Energy Engineering
• /
• v.9 no.4
• /
• pp.348-357
• /
• 2000

본 연구에서는 동해화력 순환유동층 보일러와 유사한 3개의 사이클론을 갖는 직사각형 구조의 순환유동층 반응기를 이용하여 동해화력 운전조건 -연소로 공기 속도, 일-이차 공기비, 전체 고체량(inventory), 입도 및 입도분포 등- 에 따른 축방향 고체 체류량 및 순환량 등의 수력학적 특성을 고찰하였다. 상승관에서의 공기유속(U$_{0}$)이 증가함에 따라, 또는 PA/[PA+SA]비가 증가함에 따라, 그리고 전체 고체량(inventory)이 증가함에 따라 고채 채류량 및 순환량은 증가하는 것으로 나타났다. 또한 넓은 입도 분포를 갖는 석탄 회재의 경우는 균일한 입도 분포의 입자들에 비해 입자 비산량 및 고체 순환량이 작을 것으로 나타났다. 한편, 층내에서의 고체 체루량 분포를 감소지수 a 및 K를 사용하여 나타낼 수 있었으며, a 및 K와 유속 및 입자간의 상관 특성치를 도출하여 유동 및 순환특성을 고찰하였다. 상기의 상관수는 균일한 입도의 모래에 비해 석탄회재가 비교적 큰 값을 나타내었으며, 상관수가 클수록 희박상 영역에서의 비산 및 고체 순환량이 작은 것으로 나타났다.다.

• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.83-88
• /
• 2011

Holdup characteristics of small bubbles were investigated in a viscous slurry bubble column. The phase holdup of small bubbles was obtained from the knowledge of total bubble(gas) holdup and large bubble holdup, which were measured by mean of static pressure drop method and dual resistivity probe method, respectively. Effects of gas velocity, viscosity of continuous liquid phase and solid fraction in the slurry phase on the small bubble holdup as well as holdups of total bubble(gas) and large bubble in a viscous slurry bubble column. The small bubble holdup increased with increasing gas velocity but decreased with increasing liquid viscosity or solid fraction in the slurry phase. In addition the fraction of small bubble in the total bubble(gas) holdup increased with increasing gas velocity but decreased with increasing liquid viscosity or solid fraction in the slurry phase. It was revealed that the rising velocity of large bubble did not related to the holdup of small bubble in a viscous slurry bubble column.

• Clean Technology
• /
• v.17 no.1
• /
• pp.62-68
• /
• 2011

Hydrodynamic characteristics in multistage annular type fluidized bed (riser: $0.01{\times}0.025{\times}2.8m^3$, J-valve: $0.009{\times}0.015m^2$)were investigated. Glass beads ($d_p=101{\mu}m$, ${\rho}_b=1,590kg/m^3$, $U_{mf}=1.25{\times}10^{-2}m/s$, Geldart classification B) was used as a bed material. Accumulated weight by the electronic balance was measured to determine the solid flow rate in batch-type. In circulation condition, we measured the accumulated weight of particle transported from riser. At the steady state condition, solid circulation rate was calculated from time interval of the heated bed material passing between two thermocouples. Solid flow rate increased with increasing inlet gas velocity ($1.2-2.6U_{mf}$) and the static bed height (z, 0.24-0.68 m) from 2.2 to 23.4 kg/s. However, mean residence time decreased with increasing inlet gas velocity ($1.2-2.6U_{mf}$) and the static bed height (z, 0.24-0.68 m) from 1,438 to 440 s. The solid holdup in the riser was determined by measuring pressure differences according to the riser height. These results showed a similar trend to that of simple exponential decay type except for the top section of the riser. To verify the gas bypassing from top bubbling beds to middle bubbling beds, $CO_2$ gas was injected by tracer gas in constant ratio, and then was measured $CO_2$ concentration in outlet gas by gas chromatography. Gas bypassing occurred below 2.6% which is negligible value.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2000.04a
• /
• pp.143-146
• /
• 2000

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.359-364
• /
• 2010

Three kinds of functional regions such as continuous slurry(${\varepsilon}_f$), bubble(${\varepsilon}_b$) and wake(${\varepsilon}_w$) regions were identified, and the individual phase holdups of each functional region were determined in a three-phase slurry bubble column of 0.152 m ID. The holdups of bubble and wake were measured by adopting the electrical resistivity probe method. Effects of gas velocity and solid concentration in the slurry phase on the individual holdups of functional regions in the column were discussed. The holdup of continuous slurry phase decreased but that of bubble or wake increased, with an increase in the gas velocity in the column. The increase of solid content in the slurry phase could lead to the increase in the holdup of continuous slurry phase but decrease in the bubble or wake holdup. The portion of wake holdup was in the range of 15~40% of the bubble holdup, which decreased with increasing gas velocity or solid content in the slurry phase. The individual holdups of three functional regions were well correlated with operating variables within this experimental conditions.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.790-797
• /
• 2011

Hydrodynamic similarity was analyzed by employing scaling factor in three phase fluidized beds. The scaling factor was defined based on the holdups of gas, liquid and solid particles and effectivity volumetric flux of fluids between the two kinds of fluidized beds with different column diameter. The column diameter of one was 0.102 m and that of the other was 0.152 m. Filtered compressed air, tap water and glass bead of which density was 2,500 kg/$m^3$ were used as gas, liquid and solid phases, respectively. The individual phase holdups in three phase fluidized beds were determined by means of static pressure drop method. Effects of gas and liquid velocities and particle size on the scaling factors based on the holdups of each phase and effective volumetric flux of fluids were examined. The deviation of gas holdup between the two kinds of three phase fluidized beds decreased with increasing gas or liquid velocity but increased with increasing fluidized particle size. The deviation of liquid holdup between the two fluidized beds decreased with increasing gas or liquid velocity or size of fluidized solid particles. The deviation of solid holdup between the two fluidized beds increased with increasing gas velocity or particle size, however, decreased with increasing liquid velocity. The deviation of effective volumetric flux of fluids between the two fluidized beds decreased with increasing gas velocity or particle size, but increased with increasing liquid velocity. The scaling factor, which was defined in this study, could be effectively used to analyze the hydrodynamic similarity in three phase fluidized processes.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.11a
• /
• pp.31-34
• /
• 1999

기-고체간의 접촉효율이 높고, 층 내 전체에 걸쳐서 균일한 기-고의 접촉을 갖는 등 많은 장점이 있어 석탄연소로, 촉매반응기와 같은 여러 기-고 반응기에 적용이 확대되고 있는 순환유동층은 높은 유속에서 조업되므로 상승관내 고체입자들은 즉시 비산하게 된다. 따라서, 원활한 반응에 필요한 상승관내 적절한 고체체류량 유지를 위해 고체입자들 대부분은 싸이클론에서 포집 되어 고체재순환부에 의하여 상승관내로 재주입 된다.(중략)

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.200-205
• /
• 2011

Axial and radial distributions of bubble holdup were investigated in a slurry bubble column with pilot plant scale(D=1.0 m). Effects of gas velocity, surface tension of continuous liquid medium and solid fraction in the slurry phase on the axial and radial distributions of bubble holdup were examined. The bubble holdup decreased with increasing radial dimensionless distance from the center of the column, while it increased with increasing dimensionless distance in the axial direction from the distributor, in all the cases studied. The radial non-uniformity of bubble holdup increased with increasing gas velocity but decreasing surface tension of liquid medium, while it was not dependent upon the solid fraction in the slurry phase. The axial non-uniformity of bubble holdup increased with increasing gas velocity, but it does not change considerably with variations of liquid surface tension or solid fraction in the slurry phase . The axial and radial distributions of bubble holdup were well correlated in terms of operating variables within this experimental conditions.