• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.88.1-88.1
• /
• 2011

SOFC는 사용되는 셀의 디자인에 따라 튜브형, 평판형으로 구분되어진다. 평판형의 경우에는 전해질 지지형(ESC), Anode 지지형(ASC) 및 금속 지지형(MSC)로 크게 나눌 수 있다. SOFC 스택은 이와 같은 셀과 밀봉재, 집전체, 분리판의 구성요소를 여러 장으로 적층하여 이루어진다. SOFC 발전시스템은 SOFC 스택과 EBOP, MBOP로 구성되는데, SOFC 발전시스템의 상용화를 위해 선행되어야 할 것은 스택의 안정적 출력 및 신뢰성 확보이다. 즉, 셀, 밀봉재, 분리판 및 집전체로 대변되는 구성요소들이 스택에 장착되었을 때 그 기능을 최대한 발휘하면서도 점진적 또는 급격한 품질저하가 발생되지 말아야 한다. 특히, 밀봉재의 경우 SOFC에 사용되는 연료와 공기의 혼합(Cross-over)을 방지하는 중요한 기능을 담당하고 있으며 여러 장 적층된 분리판의 전기적 단락을 방지해야 한다. 또한 SOFC의 특성상 $700^{\circ}C$ 이상의 고온에서 다른 구성요소와 화학적 반응이 없어야하고 열싸이클(Thermal cycle)을 견딜 수 있도록 충분한 기계적 강도가 보장되어야 하는 등 요구되는 품질기준이 엄격하다. SOFC의 밀봉재는 접합형(Brazing), 압착형(Compressive), 용융-고정형(Glass-ceramic)이 대표적으로 적용되고 있다. 이 중에서 Brazing 물질과 방법은 현재 활발히 연구가 수행 중에 있지만 범용적으로 사용되고 있지는 않은 상태이고 Compressive 밀봉재와 Glass-ceramic 밀봉재가 대면적 SOFC 스택에 사용되어 적용 가능성을 평가받고 있다. 본 연구에서는 SOFC 구성요소의 국산화를 추진하는 지경부과제의 결과물 중 (주)써모텍에서 개발한 Glass-ceramic 밀봉재(RC1) 단품에 대한 특성평가와 실제 단전지 평가를 통해 SOFC 스택 적용 가능성을 평가하였다. 밀봉재 단품에 대한 특성평가는 용융특성, 상분석, 열팽창계수 등의 물리적, 화학적 평가 외에 가스 누설 정도를 평가하는 기밀도 평가와 SOFC의 작동 온도인 $700^{\circ}C$와 상온 분위기를 주기적으로 인가하는 Thermal cycle 특성을 평가하였다. 셀을 한 장 사용하는 단전지(Unit cell) 평가는 RIST에서 자체 제작한 $100{\times}100mm^2$ 평판형 ASC 셀을 사용하여 수행하였으며, 밀봉재는 Dispensing 공정을 통해 구성되었다.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.172-177
• /
• 2010

This study reports the high-temperature oxidation kinetics, ASR(area specific resistance), and interfacial microstructure of metallic interconnects coated with conductive oxides in oxidation atmosphere at $800^{\circ}C$, The conductive material LSC($La_{0.8}Sr_{0.2}CoO_3$, prepared by Solid State Reaction) was coated on the Crofer22APU. The contact behavior of coating layer/metal substrate was increased by sandblast. The electrical conductivity of the LSC coated Crpfer22APU was measured by a DC two probe four wire method for 4000hr, in air at $800^{\circ}C$. Microstructure and composition of the coated layer interface were investigated by SEM/EDS. These results show that a coated LSC layer prevents the formation and growth of oxide scale such as $Cr_2O_3$ and enhances the long-term stability and electrical performance of metallic interconnects for SOFCs.

• Korean Chemical Engineering Research
• /
• v.59 no.4
• /
• pp.557-564
• /
• 2021

Sr_0.92Y_0.08Ti_1-xV_xO_3-δ (SYTV) with perovskite structure was investigated as an alternative anode to utilize H₂S containing fuels in solid oxide fuel cells. To improve the electrochemical performance of Sr_0.92Y_0.08TiO_3-δ (SYT), vanadium(V) was substituted to titanium(Ti) at the B-site of the SYT perovskites. The SYTV synthesized by the Pechini method was chemically compatible with the YSZ electrolyte without additional by-products formation under the cell fabricating conditions. As increasing V substitution amounts, the oxygen vacancies increased, resulting to increasing ionic conductivity of the anode. The cell performance in pure H₂ at 850 ℃ is 19.30 mW/cm² and 34.87 mW/cm² for a 1 mol.% and 7 mol.% of V substituted anodes, respectively. The cell performance using H₂ fuel containing 1000 ppm of H₂S at 850 ℃ was 23.37 mW/cm² and 73.11 mW/cm² for a 1 mol.% and 7 mol.% of V substituted anodes, respectively.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.8
• /
• pp.570-576
• /
• 1999

$LaCrO_3$-dispersed Cr alloys for metallic interconnector of solid oxide fuel cell have been studied as function of $LaCrO_3$ content in the range of 5 to 25 vol.% in order to examine the electric conductivity, the oxidation property and the thermal expansion behavior of these alloys. The $LaCrO_3$-dispersed Cr alloys showed high electrical conductivities of $3~5\times10^4$ S/cm at room temperature, and as the $LaCrO_3$content increased the conductivity decreased slightly. During the cyclic oxidation test at $1100^{\circ}C$, the weight change of the Cr alloys decreased with increasing number of oxidation cycle except first cycle, which is attributed to the vaporization of the oxide scale. More addition of the $LaCrO_3$ content reduced also the weight change of the Cr alloys. These mean that the oxide scale formed at the surface of the Cr alloy becomes stable with increasing number of oxidation cycle and$LaCrO_3$ content. The measured thermal expansion of the Cr alloy was well fitted to that of 8 mol% $Y_2O_3$-stabilized $ZrO_2$ electrolyte. These results demonstrate that $LaCrO_3$-dispersed Cr alloy is a useful material for metallic interconnector of solid oxide fuel cell.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.341-347
• /
• 2010

In this study, the efficiency of a solid-oxide fuel cell (SOFC) system with a steam reformer or prereformer was analyzed under various conditions. The main components of the system are the reformer, SOFC, and water boiling heat recovery system. Endothermic and exothermic reactions occur in the reformer and SOFC, respectively. Hence, the thermal management of the SOFC system greatly influences the SOFC system efficiency. First, the efficiencies of SOFC systems with a steam reformer and a prereformer are compared. The system with the prereformer was more efficient than the one with steam reformer due to less heat loss. Second, the system efficiencies under various prereformer operating conditions were analyzed. The system efficiency was a function of the heat requirement of the system. The efficiency increased with an increase in the operating temperature of the prereformer, and the maximum system efficiency was observed at $450^{\circ}C$ for a S/C of 2.0.

• Journal of the Korean Society of Safety
• /
• v.30 no.1
• /
• pp.21-27
• /
• 2015

In this study, interfacial characteristics between SOFC and Ag paste as current collector was estimated in the high temperature environment. The Ag paste was used to connect the unit cell of SOFC strongly with interconnector and provide the electrical conductivity between them. To confirm electrical conductivity, Ag paste was treated in the furnace at $800^{\circ}C$ for 48 hours. The sheet resistance of Ag paste was measured to compare the resistance values before and after the heat treatment. Also, the four-point bending test was performed to measure the interfacial adhesion. The unit cell of SOFC and $SiO_2$ wafer were diced and then attached by Ag paste. The $SiO_2$ wafer had the center notch to initiate a crack from the tip of the notch. The modified stereomicroscope combined with the CCD camera and system for measuring the length was used to observe the fracture behavior. To compare the characteristics before heat treatment and after heat treatment, the specimen was exposed in the furnace at $800^{\circ}C$ for 48 hours and then the interfacial adhesion was evaluated. Finally, the interfacial adhesion energy quantitatively increases $1.78{\pm}0.07J/m^2$ to $4.9{\pm}0.87J/m^2$ between the cathode and Ag paste and also increase $2.9{\pm}0.47J/m^2$ to $5.12{\pm}1.01J/m^2$ between the anode and Ag paste through the high temperature. Therefore, it is expected that Ag paste as current collector was appropriate for improving the structural stability in the stacked SOFC system if the electrical conductivity was more increased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.462-462
• /
• 2009

$CeO_2$는 고체 산화물 연료전지 (SOFC, soild oxide fuel cell)의 전해질 재료와 CMP(Chemical Mechanical Polishing) 슬러리 재료, 자동차의 3원 촉매, gas sensor, UV absorbent등 여러 분야에서 사용되고 있다. 본 연구에서는 위의 활용범위 외에 $CeO_2$의 구조적 안정성과 빠른 $Ce^{3+}/Ce^{4+}$의 전환 특성을 이용하여 lithium ion battery의 anode 재료로서 전기화학적 특성을 알아보고자 실험을 실시하였다. $CeO_2$ 합성에 사용되는 전구체인 cerium carbonate의 형상 및 크기, 비표면적과 같은 물리화학적 특성이 $CeO_2$ 분말의 특성에 직접적인 영향을 주기 때문에 전구체의 합성 단계에서 입자의 특성을 조절하였다. 전구체 합성의 출발원료로 cerium nitrate hexahydrate 와 ammonium carbonate를 사용하였고 반응온도 및 농도 등을 변화시켜 입자의 형상 및 결정상을 fiber형태의 orthorombic $Ce_2O(CO_3)_2{\cdot}H_2O$와 구형의 hexagonal $CeCO_3OH$의 세리아 전구체를 합성하였다. 이를 $300^{\circ}C$에서 30분 동안 하소하여 전구체의 입자형상을 유지하는 cubic $CeO_2$를 합성하고 X-ray diffraction, FE-SEM, micropore physisorption analyzer 분석을 통하여 입자의 결정상과 형상, 비표면적 등을 비교 분석하고 $Li/CeO_2$ couple의 충,방전 용량과 수명특성을 비교 분석하여 $CeO_2$의 전기화학적 특성을 알아보았다.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.425-431
• /
• 2005

Line Shaped Solid Oxide Fuel Cell (SOFC) with multilayered structure has been fabricated via direct-writing process. The cell is electrolyte of Ni-YSZ cermet anode, YSZ electrolyte and LSM cathode. They were processed into pastes for the direct writing process. Syringe filled with each electrode and electrolyte paste was loaded into the computer-controlled robe-dispensing machine and the paste was dispensed through cylindrical nozzle of 0.21 mm in diameter under the air pressure of 0.1 tow onto a moving plate with 1.22 mm/s. First of all, the anode paste was dispensed on the PSZ porous substrate, and then the electrolyte paste was dispensed. The anode/electrolyte and the PSZ substrate were co-fired at $1350^{\circ}C$ in air atmosphere for 3 h. The cathode layer was similarly dispensed and sintered at $1200^{\circ}C$ for 1 h. All the electrode/electrolyte lines were visually aligned during the direct writing process. The effective reaction area of fabricated SOFC was $0.03 cm^2$, and the thickness of anode, electrolyte and cathode was 20 $\mu$m, 15 $\mu$m, and 10 $\mu$m, respectively. The single line-shaped SOFC fabricated by direct-writing process exhibited OCV of 0.95 V and maximum power density of $0.35W/cm^2$ at $810^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.85-91
• /
• 2006

Electron Beam Physical Vapor Deposition (EB-PVD) was applied to fabricate a thin film YSZ electrolyte with large area on the porous NiO-YSZ anode substrate. Microstructural and thermal stability of the as-deposited electrolyte film was investigated via SEM and XRD analysis. In order to obtain an optimized YSZ film with high stability, both temperature and surface roughness of substrate were varied. A structurally homogeneous YSZ film with large area of $12\times12\;cm^2$ and high thermal stability up to $900^{\circ}C$ was fabricated at the substrate temperature of $T_s/T_m$ higher than 0.4. The smoother surface was proved to give the better film quality. Precise control of heating and cooling rate of the anode substrate was necessary to obtain a very dense YSZ electrolyte with high thermal stability, which affords to survive after post heat treatment for fabrication a cathode layer on it as well as after long time operation of solid oxide fuel cell at high temperature.

• Journal of the Korean Ceramic Society
• /
• v.42 no.9 s.280
• /
• pp.637-644
• /
• 2005

In order to find a proper buffering material which can prohibit an unwanted interfacial reaction between anode and electrolyte of LSGM-based SOFC, we examined a gadolinium doped ceria and scandium doped zirconia as a candidate. For this examination, we investigated the microstructural and phase stability of the interface under different buffering layer conditions. According to the investigation, ceria based material induced a serious La diffusion out of the LSGM electrolyte resulted in the formation of very resistive $LaSrGa_3O_7$ phase at the interface. On the other hand zirconia based material was directly reacted with LSGM electrolyte and thus produced very resistive reaction products such as $La_2Zr_2O_7,\;Sr_2ZrO_4,\;LaSrGaO_4\;and\;LaSrGa_3O_7$. From this study we found that an improper buffering material induced the higher internal cell resistance rather than an interfacial stability.