• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.127-130
• /
• 2002

In this study, development of a new LTCC material using a non-glassy system was attempted with respect to reducing the fabrication process steps and cost down. Lowering the sintering temperature can be achieved by liquid phase sintering. For LTCC application, the starting material must have quality factor as high as possible in microwave frequency range. And also, the material should have a low dielectric constant for enhancing the signal propagation speed. Regarding these factors, dielectric constants of various materials were estimated by the Clausius-Mosotti equation. Among them, CaWO$_4$ was tamed out the suitable LTCC material. CaWO$_4$ can be sintered up to 98% of full density at 1200$^{\circ}C$ for 3 hours. It's measured dielectric constant, quality factor, and temperature coefficient of resonant frequency were 10.15, 62880GHz, and -27.8ppm/$^{\circ}C$, respectively. In order to modify the dielectric properties and densification temperature, 0.5∼1.5 wt% LiF were added to CaWO$_4$. LiF addition reduced the sintering temperature/time down to 800$^{\circ}C$/10∼30min due to the reactive liquid phase sintering. Dielectric constant lowered from 10.15 to 9.38 and Q x fo increased up to 92000GHz with increasing LiF content.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.25-35
• /
• 1999

LTCC (Low Temperature Cofired Ceramic) or LTCC-M (Low Temperature Cofired ceramic on Metal) technology is one of MCM-C (Multichip Module on Ceramic) technologies and becomes to be widely used in consumer, RF and automotive electronics. As green sheets for LTCC are cofired below $1000^{\circ}C$ in comparison with those for HTCC (High Temperature Cofired Ceramic), high conductivity metal traces such as gold, silver and copper can be used. The dimensional stability in LTCC-M technology enables embedded passives to be integrated inside modules, which enhances the electrical performance and increases the reliability of the modules. Coefficient of thermal expansion and dielectric constant can be controlled by changing composition and heating profile for cofiring. In this technical review, LTCC and LTCC-M technologies are introduced and advantages of those technologies are explained.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.5
• /
• pp.30-35
• /
• 1993

We have investigated microwave dielectric properties of TiO$_{2}$ added (Pb$_{1-x}$Ca$_{x}$)ZrO$_{3}$ Ceramics with x=0.33, 0.35, and 0.37 sintered at 1400$^{\circ}C$ for 2 h. For additions of up to 3wt% of TiO$_{2}$ in (Pb$_{0.63}$ Ca$_{0.37}$)ZrO$_{3}$ (x=0.37), TiO$_{2}$ was completely soluble in (Pb, Ca)ZrO3 phase and did not affect the grain size of ceramics. Dielectric constant and temperature coefficient of resonant frequency increased due to the formation of solid solution, whereas Q value decreased linearly as TiO$_{2}$ increased up to 1 wt%. However, the dielectric loss was very high as TiO$_{2}$ exceeded 2 wt%. It was also shown that as Ca ion content in 0.5 wt% TiO$_{2}$ added (Pb$_{1-x}$,Ca$_{x}$)ZrO$_{3}$ decreased from x=0.37 to x=0.33, dielectric constant increased and Q value decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.292-294
• /
• 1996

Dielectric properties were investigated at Mn doped 0.17($Ba_{0.53}$, $Pb_{0.47}$)0-$0.16Nd_2O_3$-$0.67TiO_2$ system in microwave frequency. It was observed that dielectric constant of 90.1, quality factor of 1320 (at 3.8GHz) and temperature coefficient of resonance frequency 2.3 ppm/$^{\circ}C$ for 0.5wt% Mn doped 0.17($Ba_{0.53}$, $Pb_{0.47}$)0-$0.16Nd_2O_3$-$0.67TiO_2$ system in sintering condition $1290^{\circ}C$/2hr. The quality factor increase due to the compensation effect of Mn ions yp to 0.5wt% and the decrease due to the interface relaxation effect. The temperature coefficient of resonance frequency increases to negative direction with increasing the amounts of Mn.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.4
• /
• pp.983-990
• /
• 2010

In this paper, we designed and implemented the MIMO antenna for LTE(Long Term Evolution), supposed to be a next generation communications network, DCS1800, DCS1900 and WCDMA. Using conventional monopole antenna with MD material results in good characteristics, miniaturization for LTE band and as well as broadbanding for DCS, WCDMA band. The performance of the proposed MIMO antenna shows VSWR < 2, under -10 dB of isolation and the gain is -1.66 ~ 1.33 dBi for LTE(Long Term Evolution), DCS1800, DCS1900 and WCDMA, which has omnidirectional radiation pattern.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.125-129
• /
• 2004

[ $BaTi_4O_9$ ] thin film were grown on $Pt/Ti/SiO_2/Si$ substrate using rf magnetron sputter, and the microstructure and dielectric properties of the thin films were investigated. For the film grown at $350^{\circ}C$ and rapidly thermal annealed at $900^{\circ}C$, the $BaTi_5O_{11}$ Phase was formed. However, the $BaTi_4O_9$ phase was formed when the growing temperature exceeded $450^{\circ}C$ The dielectric constant of the $BaTi_4O_9$ thin film grown at $550^{\circ}C$ and rapidly thermal annealed at $900^{\circ}C$ was about 40 at low frequency range($100kHz{\sim}1MHz$) and 36 at microwave range($1{\sim}10GHz$) which is very close to that of the bulk $BaTi_4O_9$ phase. The dissipation factor was very low, about 0.005 at low frequency as well as microwave range.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.242-248
• /
• 2000

BST thin films were prepared with various deposition conditions by rf-magnetron sputtering. As substrate temperature increases and Ar/$O_2$ratio decreases, the electrical properties of the BST films improve. The conventional Schottky model and modified-Schottky model were introduced in order to investigate the leakage-current-conduction mechanisms of the deposited films. It was found that the modified-Schottky model better describes the current-conduction mechanism in the BST films than the conventional Schottky model. From the modified-Schottky model, optical dielectric constant ($\varepsilon$), electronic drift mobility ($\mu$), and barrier height $({\phi}_b)are calculated as $\varepsilon$=4.9, $\mu$=0.019 $\textrm{cm}^2$/V-s, and ${\phi}_b=0.79 eV.

• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.37-43
• /
• 1999

Co-firing incompatibility between the low temperature sinterable Glass/ceramic and Ag-thick film was studied. The dielectric material, which has been developed for microwave frequency applications, consists of $SiO_2-TiO_2-Bi_2O_3$-$Bi_2O_3$-RO system(RO:BaO -CaO-SrO) crystallizable glass and $Al_2O_3$as a ceramic filler. The large camber in the sintered specimen and cracks at the Ag-film under the influence of the camber occurred due to the difference of densification rate between the ceramic sheet and the Ag-film $B_2O_3$addition to the Glass/ceramic mixture reduced the severe camber. The cambers decreased with increasing the $B_2O_3$ content, and completely disappeared with 14 vol% $B_2O_3$addition. With additions of $B_2O_3$, $\varepsilon_{r}$ decreased abruptly, Q$\times$f value increased largely and the $\tau_f$ value of the material quickly shifted to positive one.

• Korean Journal of Crystallography
• /
• v.17 no.1
• /
• pp.24-32
• /
• 2006

The microwave dielectric properties of $Zn_3Nb_2O_8\;with\;V_2O_5$ addition were investigated. The addition of $V_2O_5$ enhanced the sinterability of $Zn_3Nb_2O_8$, which resulted in high density of $Zn_3Nb_2O_8$ ceramic greater than 95% of the theoretical value when sintered at $900^{\circ}C$ for 4 hours. X-ray diffraction analysis of sintered $Zn_3Nb_2O_8$ ceramic showed no second phase with $V_2O_5$ addition. Dielectric permittivity(${\varepsilon}_r$) and quality factor($Q{\times}f$) varied with both density at different sintering temperature and $V_2O_5$ addition. Dielectric permittivity, quality factor and temperature coefficient($T_{cf}$) of the two mole of $V_2O_5\;added\;Zn_3Nb_2O_8$ that was sintered at $900^{\circ}C$ were 21.4, 40,000, $-54ppm/^{\circ}C$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.1046-1054
• /
• 2001

Effects of B$_2$O$_3$and CuO addition on the microwave dielectric properties of the PbWO$_4$-TiO$_2$ceramics were investigated in order to use this material as an LTCC material for fabrication of a multilayered RF passive components module. We found that PbWO$_4$could be used as an LTCC material because of its low sintering temperature (8$50^{\circ}C$) and fairy good microwave dielectric properties($\varepsilon$$_{r}$=21.5, Q$\times$f$_{0}$=37200 GHz and $\tau$$_{f}$ =-31 ppm/$^{\circ}C$). In order to stabilize $\tau$$_{f}$ of PbWO$_4$, TiO$_2$was added to the PbWO$_4$and the mixture was sintered at 8$50^{\circ}C$. A near zero $\tau$$_{f}$ value (+0.2 ppm/$^{\circ}C$) was obtained with 8.7 mol% TiO$_2$addition. $\varepsilon$r and Q$\times$f$_{0}$ values were 22.3 and 21400 GHz, respectively. It was believed that the decrement of Q$\times$f$_{0}$ value with TiO$_2$addition was resulted from increasing grain boundary. In order to improve Q$\times$f$_{0}$, various amounts of B$_2$O$_3$and CuO were added to the 0.913PbWO$_4$-0.087TiO$_2$mixture. The optimum amount of CuO was 0.05 wt%. At this addition, the 0.913PbWO$_4$-0.087TiO$_2$ceramic showed $\varepsilon$$_{r}$=23.5, $\tau$$_{f}$ =-2.2ppm/$^{\circ}C$, and Q$\times$f$_{0}$=32900 GHz after sintered at 8$50^{\circ}C$. In case of B$_2$O$_3$addition, the optimum amount range was 1.0~2.5 wt% at which we could obtain following results; $\varepsilon$$_{r}$=20.3~22.1, Q$\times$f$_{0}$=48700~54700 GHz, and $\tau$$_{f}$ =+2.4~+8.2ppm/$^{\circ}C$.