• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1103-1105
• /
• 1993

Microwave characteristics of the system (1-X) ${Na}_{1/2}{Sm}_{1/2}TiO_3$[NST]-X ${Li}_{1/2}{Nd}_{1/2}TiO_3$[LNT] were investigated. The dielectric constant and unloaded Q were 86,1950 respectively for NST at 3GHz and 80,500 for LNT. 0.4 NST - 0.6 LNT system has the dielectric constant ${\varepsilon}r$=86.2, Q=930(3GHz), temperature coefficient of the resonant frequency ${\tau}f$ = 8 ppm/$^{\circ}C$ when sintered at $1450^{\circ}C$ for 2h.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.57-58
• /
• 2005

The properties such as capacitance and resonant frequency are important in embedded capacitors. Accurate equivalent model is required to find these properties of embedded capacitor. In this paper, we investigate to analyze the properties of high-K embedded capacitor which was fabricated by Low Temperature Co-fired Ceramic (LTCC). Modeling based on partial element equivalent circuit (PEEC) method is performed using HSPICE circuit simulation. This modeling methodology can provide the good inspection of embedded capacitor to device engineer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.263-266
• /
• 2001

In this paper, we investigated dielectric properies for BST thin films that was deposited on MgO/Si substrates using RF magnetron sputtering. In here, MgO film was used to perform that a diffusion b arrier between the BST film and Si substrate and a buffer layer to assist the BST film growth. A d eposition condition for MgO films was RF Power of 50W, substrate temperature of room temperature and the working gas ratio of Ar:O$_2$ were varied from 90:10 to 60:47. Finally we manufactured the cap acitor of Al/BST/MgO/Si/Al structure to know electrical properties of this capacitor through I-V, C-V measurement. In the results, C-V aha racteristic curves was shown a ferroelectric property so we measured P-E. A remanent poliazation and coerceive electric field was present 2$\mu$C/cm$^2$ and -27kV/cm respectively at Ar:O$_2$=90:10. And a va clue of dielectric constant was 86 at Ar:02=90:10.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.3
• /
• pp.471-481
• /
• 1995

Measurement factors for the dielectric properties of low dielectric loss materials (tan${\dalta}{\le}10^{-4}$) were investigated using the dielectric rod resonator method. It was shown that the relative conductivity (${\sigma}_{r}$) should be controlled within a 5% to obtain the standard deviations of less than 0.07 for permittivity .epsilon.r and 0.06${\times}10^{-4}$ for tan.delta.respectively. Surface resistivity (R$_s$) could be reduced when the surface roughness of parallelled conducting plate was less than 0.07 .mu.m. Measurement error for the permittivity was $\pm$0.02% independent of probe loop size, whereas the error in Q value was reduced with the decrease in probe loop size and also with the increase in the absolute values of Q. Reliable Q values were determined with the probe loop size of less than 4mm. The accurate for the distance between the measuring probe loop and the sample could be obtained when the insertion loss of resonant frequency ranged -15dB - -30dB.

• Journal of the Microelectronics and Packaging Society
• /
• v.8 no.3
• /
• pp.69-75
• /
• 2001

Photoimageable thick film technology is a new technology in that the lithography process such as exposure and development is applied to the conventional thick film process. Line resolution of 25 $\mu\textrm{m}$ width and 25 $\mu\textrm{m}$ space could be obtained by laminating green sheet, printing photoimageable Ag paste, exposing the test patterns, developing, and co-firing. In case of using the alumina substrate, 20 $\mu\textrm{m}$ fine line could be also obtained by similar process. Test results showed that exposing power density and developing time were the most important processing parameters for the fine line formation. Microstrip and series gap resonators with well-defined line morphology and good transmission characteristics in high frequency were formed by this new technology, and thereby dielectric constant and loss of test substrate were calculated.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.5
• /
• pp.231-241
• /
• 2005

Laboratory experiments were performed to examine the effects of water content and to see if permittivity had sufficient sensitivity to identify subsurface contamination. Both real and imaginary permittivities of unsaturated sand were strongly governed by the volumetric water content. Especially, a linear relationship between real permittivity and volumetric water content was derived at high frequencies (MHz ranges). Heavy metals in pore fluid result in significant increases in the effective imaginary permittivity, due to ionic conduction, but decreases in the real permittivity arises due to the decreased orientational polarization of water molecules caused by hydration of ions. Clear increase in the effective imaginary permittivity with heavy metal concentration was found to be valuable in the application of electrical methods for detecting heavy metals in the subsurface. However, because the permittivity is primarily dependent on the volumetric water content of soil, pre-evaluation on the volumetric water content is required.

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.491-499
• /
• 1997

We fabricated the ceramic PLT tablet which was composed of 5, 10 and 15 mol% lanthanum concentration and thin film PLT to develope pyroelectric materials, and investigated their characteristics. Using TG/DTA, we determined calcination and sintering temperature to sinter the PLT completely and to prevent volatilization of the Pb components. The calcination and sintering temperature were $850^{\circ}C$, $1150^{\circ}C$ respectively, and there was a lot of mass loss at higher sintering temperature. By measuring temperature-dielectric constant characteristics of ceramic tablet we investigated dielectric constant characteristics depends on La concentration. The Curie point of PLT with 5, 10 and 15 mol% lanthanum concentration were $330^{\circ}C$, $269^{\circ}C$ and $210^{\circ}C$ respectively. Using PLT ceramic tablet we observed IR detection characteristics, and then deposited PLT thin film by rf magnetron sputtering. We verified that PLT thin film fabricated with completely sintered PLT target had the same structure to target by investigating lattice constant and optical transparency.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.11
• /
• pp.77-82
• /
• 1990

The temperature and the composition dependence of the dielectric properties of the solid solution materials in the system $xBa(Zn_{1/3}Nb_{2/3})O_{3}\[BZN]-(1-x)\Sr(Zn_{1/3}Nb{2/3)O_{3}\[SZN]$ at microwave frequency was studied. The dielectric constant and unloaded Q were $40.5{\pm}0.5,5980{\pm}100$ respectively for BZN at 10 GHz and $36.9{\pm}0.5,2700{\pm}100$ for SZN at 10.2GHz. The temperature coefficient of the resonant frequency was $+27.5ppm/{\circ}C$ for BZN and $-39.1ppm/{\circ}C$ for SZN. The results also showed that 0.3 BZN-0.7 SZN is the most temperature-stable composition among xBZN-(1-x) SZN solid solutions. In this case, the dielectric constant, the unloaded Q and $\tau_{f}$ at 9.8GHz were $41.5{\pm}0.2,2920{\pm}100$ and $-3.5ppm/{\circ}C$, respectively.

• The Journal of Engineering Geology
• /
• v.14 no.4 s.41
• /
• pp.361-369
• /
• 2004

The authors designed a new technique to measure dielectric constant of a soil media by Frequency Domain Reflectometry (FDR) system and its measurement sensor probe with different length such as 7m, 10cm and 15cm for estimating the variations of dielectric constant. Measurement of dielectric constant of soil material is possible to measure an interference wave generated by between incidence wave and reflection wave which are detected to electro-magnetic wave through the directional coupler at the high frequency range,0.1 to 1.7GHz, by FDR system. The obtained experimental results verified that the technique is very promising for non-destructive and continuous soil volumetric water content measurement monitoring in a laboratory. The relationship between the soil volumetric water content and the dielectric constant of soil media (standard sand) was expressed by a single regression ewe independent of soil texture at a small experimental error. Also the derived regression curve coincided well with that obtained by Topp curve.

• Journal of the Korean Magnetics Society
• /
• v.15 no.2
• /
• pp.67-75
• /
• 2005

For th aim of lightweight microwave absorbers, conductive and magnetic microspheres are fabricated by plating of Co films on hollow ceramic microspheres of low density. Metal plating was carried out in a two-step electroless plating process (pre-treatment of activation and plating). Uniform coating of the film with about $2{\~}3{\cal}um$ thickness was identified by SEM. High-frequency magnetic and microwave absorbing properties were determined in the rubber composites containing the Co-coated microspheres. Due to conductive and ferromagnetic behavior of the Co thin films, high dielectric constant and magnetic loss can be obtained in the microwave frequencies. Due to those electromagnetic properties, high absorption rate (25 dB) and thin matching thickness ($2.0{\~}2.5{\cal}mm$) are predicted in the composite layers containing the metal-coated microspheres of low density (about 0.84 g/cc) for the electromagnetic radiation in microwave frequencies.