• Journal of the Korean Society of Marine Environment & Safety
• /
• v.10 no.1 s.20
• /
• pp.29-33
• /
• 2004

Design of general steel structure had applied to achieve elastic designing concept so far. Because elastic design supposes that whole structure complies with elasticity formula so that achieve via allowable stress of material. It is concept that calculate stress distribution of construction about action external load and estimate load when the maximum stress reaches equally with allowable stress that is established by maximum safety load of the structure. But, absence that compose actuality structure by deal with external load increase small success surrender and structure hardness falls and structure in limited state finally on the whole as showing complicated process by interference between collapse and buckling under compression. Applied ANSYS (elasto-plasticity large deformation finite element method) to be mediocrity finite element program for analysis method and analysis control used in Newton-Raphson method & Arc-length method.

• Elastomers and Composites
• /
• v.40 no.3
• /
• pp.196-203
• /
• 2005

In this work, the engine oil resistant evaluation and breakdown analysis of room temperature vulcanizing silicone adhesives were performed through the surface properties, thermal stabilities, adhesive strength, and morphology measurements. As a result, the permeation of engine oil into adhesive specimens was carried out from surface to center in the specimens. And the oil content in the adhesive specimens was increased and the Si-O-Si bond of the adhesives was decomposed with increasing the aging time. The TGA results indicated that the thermal degradation was mainly occurred at under and surfaces of the specimens. The tensile strength, elongation, and adhesive strength of the adhesives were significantly decreased after the engine oil resistant tests, which could be attributed to the initial lose of adhesive properties resulting from the engine oil absorption and thermal aging. And the failure mode of the adhesive specimens was changed from cohesive failure to interfacial failure.

• Journal of the Korean Institute of Gas
• /
• v.21 no.6
• /
• pp.15-22
• /
• 2017

The pressure safety valve is very important device for securing the safety in the facilities which is operated by high pressure gases. The performance test should be periodically inspected by relate law because the failure of pressure safety valves might be main causes of serious accidents in the industrial fields. Shop test is mainly use for inspecting the performance test of pressure safety valves but the test method is not to be a solution for securing the safety. So, the development of alternative method is required. In this paper, there is a limit to securing the safety if the performance test is with just shop test. The limitation is checked from analysis result based on performance test results of pressure safety valves. The necessity for introducing the in-service test is reviewed to surmount the limitation. As a result, in-service test method should be developed and introduced to improve the inspection efficiency and economical loss. Also, it can be reduce the risk level.

• Convergence Security Journal
• /
• v.16 no.6_1
• /
• pp.67-74
• /
• 2016

The development of weapon systems that look only be introduced as a huge budget directly related to combat rea diness. If we develop the expensive equipment it will not be the same state or have to wait a lot of time in mainten ance facilities for maintenance, which will have a profound impact on the exercise Efficiency. In order to solve this problem, the operation and use state of the weapon system requires effort to successfully p erform the duties held by the defined and assigned, Further analysis should be conducted RAM in order to reduce m aintenance manpower and logistic support costs. The role of business is to increase the RAM system reliability by L ee to Fig system failure rate from the development and maintenance, and reduced life cycle costs. Therefore, the present study was to determine the RAM to perform analysis procedures and methods and limita tions of each element, such as to maximize the effectiveness of comprehensive logistics support and help to study to become an effective logistics support.

• Vacuum Magazine
• /
• v.2 no.2
• /
• pp.49-58
• /
• 2015

진공 배기 시스템에 위험한 환경을 초래할 수 있는 모든 가능성을 찾아 낼 수는 없지만 누적된 현장 경험과 연구 결과에 맞추어 최대한 필요한 안전 조치들을 취해야 한다. 진공 배기 시스템이나 그 구성품들에 대한 심각한 파손을 유발하는 공통적인 요인들은 발화성 물질의 점화나 진공 배기 시스템의 배기구 막힘에 의해 발생한다. 따라서, 진공 펌프와 진공 시스템의 안전한 가동과 사용을 위해서는 다음과 같은 것들을 반드시 준수하여야 한다. ${\blacksquare}$ 발화성, 폭발성 공정 물질을 사용하는 진공 배기 시스템은 정규 유지 보수 작업(PM) 후 첫 번째 배기 과정은 매우 천천히 진행하여 진공 배기 시스템 내부에 급격한 난류가 형성되지 않도록 해 주어야 한다. ${\blacksquare}$ 진공 배기 시스템 내에서 발화성 물질들의 농도가 발화 영역(flammable zone, potentially explosive atmosphere)에 들어가지 않도록 하여야 한다. 이를 위해서는 불활성 가스를 이용하여 진공 펌프와 진공 배기 시스템의 가동 예상 조건이나 고장 환경하에서 안전한 농도 이하로 희석시켜야 한다. ${\blacksquare}$ 진공 펌프와 진공 배기 시스템에 장착되어 사용되는 밸브 등의 기계적 부품들이나 공정에 사용되는 물질과 공정 부산물들(by-products)로 인하여 배관, 필터 배기구 등이 막히지 않도록 하여야 한다. ${\blacksquare}$ 공정에 사용되는 물질들, 특히 산소($O_2$), 오존 ($O_3$) 등의 산화제 농도가 높을 때는 오일 회전 배인 진공 펌프(Oil rotary vane vacuum pump)에 미네랄(mineral) 오일을 사용하지 말아야 하며, PFPE(Perfluoropolyether) 오일을 사용하여야 한다. 시판되는 진공 펌프 오일 중 비발화성(non-flammable)으로 표기된 오일이라고 하더라도 산화제(oxidant)의 농도가 체적비로 30 % 넘는 공정 환경에는 사용하지 말아야 한다. ${\blacksquare}$ 진공 펌프와 진공 배기 시스템에 의해 배기되는 물질들이 물($H_2O$)과 격렬하게 반응하는 경우는 물이 아닌 다른 냉각제를 사용하여야 한다. ${\blacksquare}$ 안전하지 않다고 판단되는 상황에서는 해당 전문가의 조언이나 해당 전문가의 직접적인 현장 도움을 통해 문제를 해결하여야 한다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1916-1920
• /
• 2010

영상수위계는 카메라에 의해서 수위표를 촬영하여 촬영된 영상을 처리하여 수위값으로 변환하여 자동적으로 수위를 측정하는 장비이다. 이 수위계는 기존 수위측정 장비인 부자식, 압력식, 기포식, 초음파식, 레이다식과는 달리 수위표를 촬영한 영상으로부터 수위를 직접 눈으로 확인할 수 있는 장점이 있다. 이로 인해 영상자료로부터 측정된 수위를 검증할 수 있어 수위측정의 정확도를 향상시킬 수 있다. 그리고 수위표 영상과 더불어 관측지점 주변의 전체 영상을 동시에 촬영하여 실시간으로 전송하기 때문에 홍수시 하천 상황에 대한 모니터링 목적으로 사용될 수 있다. 영상수위계 시스템은 크게 메인제어기, 전원부, 서버부 및 카메라부로 구성되어 있다. 현재 운영되고 있는 시스템은 전원장치 리셋시 전 시스템을 리셋해야하고, 상전 단전시 전 시스템이 off된다. 그리고 별도의 통신모듈을 사용하여 장비간 통신이 이루어지고 있다. 또한 카메라부에는 렌즈와 팬/틸트를 제어하기 위한 별도의 장비가 포함되어 있고, 백색 LED 조명이 사용되어 야간에 수위인식주기마다 조명이 on/off 되고 있다. 위와 같은 전원장치의 운영으로 시스템을 안정적으로 운영할 수 없다. 그리고 수위 오인식을 최소화하기 위해서는 연속적인 수위 인식이 필요하지만, 백색 LED조명과 1초에 2프레임을 캡쳐하는 비디오 캡쳐방식에 의해 시스템을 상시로 운영하는 것이 곤란하다. 현재 운영 중인 영상수위계를 안정적으로 운영할 수 있도록 장비별로 제어가 가능하도록 전원 제어장치를 개발하였고, 상전 단전시 최소 30분 정도 전원을 유지할 수 있도록 무정전전원장치(UPS)를 설치하였으며, 측정자료의 저장장치를 하드디스크 타입에서 Flash SSD 메모리 타입으로 교체하였다. 또한 영상수위계 시스템을 상시 운영할 수 있도록 백색 LED조명을 적외선 LED조명으로 교체하였고, 1초에 1회 수위를 인식하도록 수위인식주기와 1초에 25프레임 캡쳐할 수 있도록 비디오 캡쳐방식을 개선하였다. 위와 같은 시스템의 개선으로 시스템을 안정적으로 운영할 수 있게 되어 시스템 고장에 의해 발생하는 수위 결측을 감소시킬 수 있고, 시스템의 상시 운영으로 수 위 오인식을 최소화시킬 수 있을 것으로 판단된다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.10C
• /
• pp.887-901
• /
• 2002

Software management model divided into the software project model and design estimation model, software matrices model, reliability growth model, process improvement model(or process maturity model) etc. Among these software management models, software complexity model make an estimated of the product software. For a practice of software managed, need to guideline of the static analysis of software. Especially, Software complexity model introduced for the estimation of software quantity and program complexity. In case of measurement the software matrices, its need for us to analysis of software quality and products. On the other hand, we known that complexity program include many defects and consuming of source cost. So, we apply to complexity model using of the program complexity, control structure and volume matrices, interface metrics, process complexity metrics method. In this paper, we represent that the analysis of fault data detected during the system test. Also, we analysis of program control structure and interface, volume matrices in various aspect of switching software. Others, their results utilized similar of project and system development.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.11
• /
• pp.2685-2690
• /
• 2014

WPS determines position via a two-step process. In the construction phase, a radio map is constituted by collecting radio information signals. Positioning procedure is a step of comparing the radio signal newly acquired with the radio map. If the signals collected and the radio map are different the accuracy decreases. Even though the rate of accuracy is different according to positioning algorithms, accuracy drop is an issue common to all WPS systems. Signal strength fluctuation is caused by the malfunction of the device that receives positioning signals, obstruction and channel interference, etc. In this paper, in order to solve the problem caused by signal strength change, we propose a new radio map construction technique. The proposed method is intended to constitute a strong radio map to changes in the signal strength and updated by collecting the signal strength changes to the radio map. The use of this method is expected to enhance the accuracy of WPS by actively counteracting signal fluctuation.

• Journal of KIISE:Computing Practices and Letters
• /
• v.7 no.4
• /
• pp.359-371
• /
• 2001

Project scheduling under resource constraint conditions have contained to many uncertain factors and it is perfonned by human experts. The expert identifies the activities of the project, decides the precedent relationships between these activities, and then construct the schedule using expected activity's duration. At this time, most of the scheduling methods concentrate on one of scheduling factor between activity duration and cost. And the activity duration, which is the most important factor in scheduling, is decided by heuristic of expert. Therefore it may cause uncertainty of activity duration decision and the use of this activity duration may increase the uncertainty of constructed schedule. This paper proposes Fuzzy-MOEH scheduling algorithm, which is the aggregation of the fuzzy number for deciding activity duration and applies the cost function for solving the problems of previous scheduling methods. This paper also analyze the utility and property of Fuzzy-MEOH algorithm through the comparison between Fuzzy-MEOH algorithm and existing MEOH algorithm.

• Solar Energy
• /
• v.15 no.2
• /
• pp.13-24
• /
• 1995

Korean traditional Ondol with the sensible heat storage medium has been for a long time used as residential heating system, in these days the concrete Ondol without the heat storage medium was realized as the heating system in the private houses and the apartments. This floor heating system is good for our health. But the concrete Ondol is not desirable for the energy saving and for the maintenance of comfortable room temperature because the heat storage medium is not employed in the concrete Ondol. And as the hot water circulating pipes are buried under the concrete floor, the concrete Ondol system has some kind of problems to be improved. Therefore the new type of Ondol system was developed in this study. And the new Ondol was consisted of latent heat storage material as heat storage medium with a great heat capacity and bioceramics as medium to maintain comfortable room temperature. In this study, the heat transfer characteristics of latent heat storage-bioceramic Ondol was analyzed theoretically.