• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.670-675
• /
• 2016

Both melting temperature and enthalpy of MBCA/DMTDA mixtures were measured as a function of DMTDA compositions using DSC. The thermal properties of polyurethane elastomer samples prepared with MBCA, DMTDA, and 40/60 MBCA/DMTDA mixture as curing agents were also observed using TGA. MBCA and DMTDA showed good miscibility over the entire composition range, exhibiting individual DSC melting peaks. Peak temperatures were non-linearly reduced as DMTDA concentrations increased, being approximately $60^{\circ}C$ in the case of the 40/60 MBCA/DMTDA mixture. Furthermore, melting enthalpy of the mixture was calculated as 3.8 J/g, which was only 4.3% compared to 87.3 J/g of MBCA. Based on these results, crystallization of the mixture was considered to occur very slowly, and the fluidic gel-state of the mixture was visually confirmed to be maintained over 5 days at room temperature. Thermal decomposition of polyurethane elastomer prepared with 40/60 MBCA/DMTDA curative started at about $190^{\circ}C$, which is similar to that observed for DMTDA, only except decomposition behavior over higher temperature of $400^{\circ}C$.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.04a
• /
• pp.10-10
• /
• 2000

램제트 엔진은 비추력이 높고 추력 레벨은 낮으므로, 2단 추진기관에 적합한 추진 시스템이다. 1단-추진기관의 작동이 끝나고, 2단 램제트 엔진이 점화 후 안정된 연소에 도달되기까지 비행체의 속도는 항력에 의하여, 초당 약 마하수 0.1 정도씩 감소된다. 1단 연소 후 2단 램제트로 전환되는 지연시간이 길수록 1단에서 요구되는 종말 가속도는 증가되므로, 1단이 차지하게되는 부피는 증가되고 비행체의 크기 또한 늘어나게 된다. 따라서 1단에서 2단 램제트로 천이되는데 소요되는 시간을 가능한 짧게 하는 것이 효과적이다. 그러나 램제트 엔진의 특성상 선결되어야할 다음과 같은 여러 문제들이 있다. 첫째, 1단 작동 시 공기 흡입구와 연소실은 차단벽으로 분리되어 있다가, 1단 연소후 차단막이 제거되어 외부공기가 램제트 연소실로 흡입된다. 흡입되는 공기는 흡입구의 형상에 의하여 램 압축되지만 초음속으로 연소실을 통과하게된다. 연료 주입 구에서 공급되는 연료는 연소실에서 유동의 흐름방향(streamline)에 따라서 연소실로 확산되는데, 연소되기 전에는 유속이 빠르게 노즐로 빠져 나가므로 램제트 연료가 재순환 구역(recirculation zone)으로 침투하는데 쉽지가 않다. 둘째, 연소실 입구에서 발생되는 와류 (ring vortex)는 1단 연료의 고온 연소 가스를 연소실로 확산시키는데, 비 균일한 온도 분포를 유발하여 램제트 연료의 점화에너지가 공급되는 시간이 적당하지 않을 경우 균일한 화염 전파에 악영향을 준다. 셋째, 연소실에서의 빠른 유동 조건은 연료가 연소실에 머무를 수 있는 시간을 감소시키며, 연소실 입구에서 강한 전단 응력이 발생되어 화염이 안정화되는데 악 영향을 미치게된다. 본 논문은 공기 흡입구, 연소실 및 노즐을 통합하여 수치해석을 하였으며 열유동/점화/연소등의 미케니즘을 이해하고, 주요 인자들 중 와류의 영향에 초점을 맞추었다.다고 판단되며 배기 가스 자체에 대기 공기중에 함유되어 있던 습기가 얼어붙는(Icing화) 문제가 발생하기 때문에 배기가스의 Icing을 방지하기 위하여 압축기 끝단에서 공기를 추출하여 배기부분에 송출할 필요성이 있는 것으로 판단되었다. 출구가스의 기체 유동속도가 매우 빠르므로 (100-l10m.sec) 이를 완화하기 위한 디퓨저의 설계가 요구된다고 판단된다. 또 연소기 후방에 물을 주입하는 경우 열교환기 및 기타 부분품에 발생할 수 있는 부식 및 열교환 효율 저하도 간과할 수 없는 문제로 파악되었다. 이러한 기술적 문제가 적절히 해결되는 경우 비활성 가스 제너레이터는 민수용으로는 대형 빌딩, 산림, 유조선 등의 화재에 매우 적절히 사용되어 질 수 있을 뿐 아니라 군사적으로도 군사작전 중 및 공군 기지의 화재 그리고 지하벙커에 설치되어 있는 고급 첨단 군사 장비 등의 화재 뿐 아니라 대간첩작전 등에 효과적으로 활용될 수 있을 것으로 판단된다.가 작으며, 본 연소관에 충전된 RDX/AP계 추진제의 경우 추진제의 습기투과에 의한 추진제 물성 변화는 미미한 것으로 나타났다.의 향상으로, 음성개선에 효과적이라고 사료되었으며, 이 방법이 편측 성대마비 환자의 효과적인 음성개선의 치료방법의 하나로 응용될 수 있으리라 생각된다..7%), 혈액투석, 식도부분절제술 및 위루술·위회장문합술을 시행한 경우가 각 1례(2.9%)씩이었다. 13) 심각한 합병증은 9례(26.5%)에서 보였는데 그중 식도협착증이 6례(17.6%), 급성신부전증 1례(2.9%), 종격동기흉과 폐염이 병발한 경우와 폐염이 각 1례(2.9%)였다. 14) 식도경 시행회수는 1회가 17례(54.8%), 2회가 9례(29.0%), 3회 이상이 5례(16.1%)였다.EX>$IC_{50}$/ 값이 210 $\mu\textrm{g}$/$m\ell$로서 효과적

• Journal of the Korean Chemical Society
• /
• v.46 no.1
• /
• pp.57-63
• /
• 2002

The hydropurification reaction of CTA (crude terephthalic acid) was carried out with hydrogen over PdRu/CCM (carbon-carbonaceous composite material) catalyst in a batch reactor at high temperature. The first order kinetics of hydropurification is confirmed with the linear dependence of ln(4-CBA; 4-carboxybenzaldehyde) with reaction time. The reaction condition studied is thought to represent the hydropurification well because of the linear dependence of catalytic activity on the catalyst weight. The p-toluic acid (p-tol) in solid and liquid increases with the conversion of reaction or the decrease of 4-CBA. However, the benzoic acid (BA) concentration does not depend much on the conversion. The AT (alkali transmittance) does not depend on the 4-CBA when the concentration is higher than about 0.2% which shows the 4-CBA, in itself, does not cause the coloring effect. The AT of PTA depends inversely with the concentration of 4-CBA when the 4-CBA is less than about 0.15%. This may show the coloring materials are removed in parallel with the hydrogenation of 4-CBA. The (0.3%Pd-0.2%Ru)/CCM shows larger residual catalytic activity than a commercial catalyst, 0.5%Pd/C, after using in a commercial reactor even though the former has smaller fresh activity than the latter. The palladium and ruthenium in PdRu/CCM show the synergetic effect in activity when the ruthenium concentration is about $0.2{\sim}0.35$ wt%. It may be supposed that the PdRu/CCM catalyst can be a promising candidate to replace the commercial Pd/C catalyst.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.20 no.5
• /
• pp.653-660
• /
• 2007

Since the temperature of asphalt for deck plate of steel bridge during paying procedure is relatively high as $240^{\circ}C\;to\;260^{\circ}C$, the temperature of deck plate of bridge rises mere than $100^{\circ}C$ and excessive displacement and stress could occur. In order to avoid undesirable failure of base plate and determine the optimal pavement pattern, a thorough thermal analysis is needed. General structural model which is made of beam and plate element should be modified for transient heat transfer analysis; asphalt pavement material and convection effect on surface of structure need to be added. A new technique with the Equivalent Heat Source (EHS) for numerical thermal analysis for steel bridge under thermal load of Guss asphalt pavement is proposed. Since plate/beam elements which were generally used for structural analysis for bridge cannot explain convection effect easily on plate/beam surface, EHS which is determined based on calculated temperature with convection effect is used. To verify the EHS proposed in this study, numerical analyses with plate elements are performed and the results are compared with estimated temperatures. EHS might be used for other thermal analyses of steel bridge such as welding residual stress analysis and bridge fire analysis.

• Journal of the Korean Vacuum Society
• /
• v.14 no.2
• /
• pp.91-96
• /
• 2005

The silicon-on-insulator (SOI) wafer fabrication technique has been developed by using ion-cut process, based on proton implantation and wafer bonding techniques. It has been shown by SRIM simulation that 65keV proton implantation is required for a SOI wafer (200nm SOI, 400nm BOX) fabrication. In order to investigate the optimum proton dose and primary annealing condition for wafer splitting, the surface morphologic change has been observed such as blistering and flaking. As a result, effective dose is found to be in the $6\~9\times10^{16}\;H^+/cm^2$ range, and the annealing at $550^{\circ}C$ for 30 minutes is expected to be optimum for wafer splitting. Direct wafer bonding is performed by joining two wafers together after creating hydrophilic surfaces by a modified RCA cleaning, and IR inspection is followed to ensure a void free bonding. The wafer splitting was accomplished by annealing at the predetermined optimum condition, and high temperature annealing was then performed at $1,100^{\circ}C$ for 60 minutes to stabilize the bonding interface. TEM observation revealed no detectable defect at the SOI structure, and the interface trap charge density at the upper interface of the BOX was measured to be low enough to keep 'thermal' quality.

• Korean Journal Plant Pathology
• /
• v.13 no.3
• /
• pp.184-190
• /
• 1997

Lesion enlargement of ginger rhizome rot was most rapid at 35~40 C, but delayed greatly as temperature decreased. Time needed for a killing a ginger plant, 22~25 cm long, was about 5 days at 35~40 C, but was 15 days at 15 C in a growth chamber test. Higher RH above 90%, higher soil moisture level above 80% of maximum soil moisture capacity, and deeper planting below 4cm enhanced the lesion development on ginger stems and rhizomes. Pythium myriotylum existed in field soil as forms of hyphal portion, hyphal swelling body, or oospore- or zoospore-like bodies, and served as the origin of its colonization. Inocula of P. myriotylum was randomly distributed in soil surface around ginger plants, but its density was decreased as increasing soil depth with the highest density at 0~10 cm soil depth. Population density of P. myriotylum did not vary significantly between the rhizoplane and the rhizosphere soil of a ginger plant, but differed greatly between the disessed and healthy plants with several to several hundreds times higher population in the diseased plants. A positive curvilinear relationship was found between P. myriotylum density and ginger rhizome rot severity.

• Journal of Life Science
• /
• v.16 no.3 s.76
• /
• pp.454-458
• /
• 2006

HSF1 is the heat shock transcription factor in Saccharomyces cerevisiae. S. cerevisiae KNU5377 can ferment at high temperature such as $40^{\b{o}}C$. We have been the subjects of intense study because Hsf1p mediates gene expression not only to heat shock, but to a variety of cellular and environmental stress challenges. Basing these facts, we firstly tried to construct the hsf1 gene-deleted mutant. PCR-method for fast production of gene disruption cassette was introduced in a thermotolerant yeast S. cerevisiae KNU5377, which allowed the addition of short flanking homology region as short as 45 bp suffice to mediate homologous recombination to kanMX module. Such a cassette is composed of linking genomic DNA of target gene to the selectable marker kanMX4 that confers geneticin (G418) resistance in yeast. That module is extensively used for PCR-based gene replacement of target gene in the laboratory strains. We describe here the generation of hsf1 gene disruption construction using PCR product of selectable marker with primers that provide homology to the hsf1 gene following separation of haploid strain in wild type yeast S. cerevisiae KNU5377. Yeast deletion overview containing replace cassette module, deletion mutant construction and strain confirmation in this study used Saccharomyces Genome Deletion Project (http:://www-sequence.standard.edu/group/yeast_deletion_project). This mutant by genetic manipulation of wild type yeast KNU5377 strain will provide a good system for analyzing the research of the molecular biology underlying their physiology and metabolic process under fermentation and improvement of their fermentative properties.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.2
• /
• pp.79-83
• /
• 2009

The glass-ceramic of the $Li_{2}O-Al_{2}O_{3}-SiO_{2}$ system was investigated to develop the low thermal expansion materials. The glass of this system was heat treated at $775^{\circ}C$ for 2 h for nucleation and subsequently at $825{\sim}900^{\circ}C$ for 2 h for crystallization. The crystal structure of the glass-ceramic of this system was a single phase of $\beta$-quartz solid solution($Li_{x}Al_{x}Si_{1-x}O_{2}$). The thermal expansion of the glass-ceramic showed $4.40{\times}10^{-7}{\sim}1.33{\times}10^{-6}K^{-1}$ between $25{\sim}300^{\circ}C$ and $1.56{\times}10^{-6}{\sim}2.53{\times}10^{-6}K^{-1}$ between $25{\sim}800^{\circ}C$, higher than lower temperature range. The mechanical strength remained almost same at around high 110 MPa with heating temperature changes.

• Journal of the Korean Ceramic Society
• /
• v.39 no.3
• /
• pp.245-251
• /
• 2002

We prepared γ-alumina beads using the amorphous alumina, obtained by fast calcination of gibbsite, and its were immersed in aqueous solution of the mixture of 21.87% nitric acid and 28.57% acetic acid. The beads thus were hydrothermaly treated at 200$^{\circ}$C for 3h, and were investigated changes of crystal, pore characteristics, $N_2$ adsorption and desorption isotherms, mechanical strengths and thermal resistance. Acicular platelet crystals of 0.1∼0.3${\mu}$m were transformed into acicular boehmite crystals of 1∼2${\mu}$m having the same crystal structure. Through this changes, we found that reversible phase transformation due to hydrothermal reaction took placed between boehmite and ${\gamma}$-alumina. In comparison to the ${\gamma}$-alumina bead before hydrothermal treatment, $N_2$ adsorption capacity was increased from 450㎖/g to 670㎖/g, and pore volume between 100${\AA}$ and 1000${\AA}$ was increased form 0.15㎖/g to 0.77㎖g, and mechanical strength was increased form 1.4MPa to 2.2MPa. Also, it showed the remarkable thermal resistance which sustained ${\theta}$-alumina crystal structure and pores between 100${\AA}$ and 1000${\AA}$ at 1000$^{\circ}$C in 40vol% steam.

• Journal of the Korean earth science society
• /
• v.25 no.6
• /
• pp.443-473
• /
• 2004

In northern Gohung granitic gneiss, porphyroblastic gneiss and migmatitic gneiss are widely distributed. Gneisses were plotted in granodiorite domain on an lUGS silica-alkali diagram. The amounts of trace elements (Li, Zn, Sc, Sr, Ni, V Y etc.) vs. $SiO_2$, somewhat decreased. Plagioclase showed a wide compositional range ($An_{32-48}$). $X_{alm}$ and $X_{sps}$ were higher in garnet rim and $X_{pyp}$ in garnet core. The rocks in the study area were formed from S and I-type magmas which generated from syn-collision and the late to post-orogenic tectonic environment. Metamorphic P-T conditions u·ere low to medium pressure, high temperature (803-913$^{\circ}C$, 6.1-7.3 kb) and overprinted by retrograde metamorphism (570-726$^{\circ}C$, 2.2-5.1 kb) and chloritization.