Journal of the Korean Recycled Construction Resources Institute
/
v.3
no.2
/
pp.165-170
/
2015
Pipe-rack structures supporting high temperature and pressure are of great importance to ensure the safety of the operation of the plants. If some damage occurred in the pipe-rack structure, the facilities not only bring damage to the commercial property, but also result in economic losses. Specially, since pipe-rack structures are exposed to various environmental conditions, it is essential to evaluate the thermal behavior of the structure caused by environmental conditions for the appropriate design and maintenance of the pipe-rack structure. Thus, based on a selected, typical pipe-rack structure, a thermal-stress coupled analysis was conducted to evaluate the temperature distributions and thermal stresses of the structure. For this, this study accounted for the operating condition of the pipe and the effect of environmental conditions, Yeosu in South Korea and Saudi Arabia in the Middle East. The results of the study showed the need for accounting for a variance in the environmental factors to evaluate the thermal behavior of the pipe-rack structure along with the working condition of pipe.
The Journal of Korean Institute of Communications and Information Sciences
/
v.28
no.8A
/
pp.620-625
/
2003
The coplanar waveguide bandpass filter using folded-line stepped-impedance resonators(SIRs) is proposed. The folded-line SIR has about λ/8 length using the short-circuited end on coplanar waveguide. It make that the bandpass filter has the half size in comparison with general λ/4 SIR filter. In this paper, we derive the equivalent circuit and design the bandpass filter by using that. We design and fabricate the bandpass filter which has 5 GHz center frequency and 3 % fractional bandwidth. The measurement results fur 4-pole folded SIR bandpass filter agreed well with full-wave simulation and equivalent circuit results. The fabricated bandpass filter has a good spurious characteristic, which the harmonic frequency appeared at 2.5f$\_$0/). The proposed folded-line SIR bandpass filter are applicable for MMIC and High-Tc superconducting filters. bandwidth.
The specimens for the corrosion test were made by hot-pressing of SiC power with 2 wt% Nl2O3 and 10wt% Al2O3 additions at 2000℃ and 2050℃. The specimens were corroded in 37 mole% NaCl and 63 mole% Na2SO4 salt mixture at 1000℃ up to 60 min. SiO2 layer was formed on SiC and then this oxide layer was dissolved by Na2O ion in the salt mixture. The rate of corrosion of the specimen containing 10 wt% Al2O3 was slower than that of the specimen containing 2 wt% Al2O3. This is due to the presence of continuous grain boundary phase in the specimen containing 10 wt% Al2O3. The oxidation of SiC produced gas bubbles at the SiC-SiO2 interface. The rate of corrosion follows a linear rate law up to 50 min. and then was accelerated. This acceleration is due to the disruption oxide layer by the gas evolution at SiC-SiO2 interface. Pitting corrosion has found at open pores and grain boundaries.
Journal of the Microelectronics and Packaging Society
/
v.17
no.1
/
pp.1-7
/
2010
Interfacial reaction characteristics of a Bi-10Cu-20Sb-0.3Ni Pb-free alloy on Cu pad was investigated by reflow soldering at $430^{\circ}C$. The thickness of interfacial reaction layers with respect to the soldering time was also measured. After the reflow soldering, it was observed that a $(Cu,Ni)_2Sb$, a $Cu_4Sb$ intermetallic layer, and a haze layer, which is consisted of Bi and $Cu_4Sb$ phases, were successively formed at the Bi-10Cu-20Sb-0.3Ni/Cu interface. The total thickness of the reaction layers was found to be linearly increased with increasing of the reflow soldering time up to 120 s. As the added Ni element did not participate in the formation of the thickest $Cu_4Sb$ interfacial layer, suppression of the interfacial growth was not observed.
We have investigated the interfacial reactions in Co/Ti multilayer thin films prepared by DC Magnetron sputtering system. We observed that the amorphous Co-Ti phase formed by SSAR (Solid State Amorphization Reaction) upon annealing at $200^{\circ}C$. Upon annealing treatments at $300^{\circ}C\;and\;400^{\circ}C$, a crystalline phase of CoTi formed at the Co/Ti interface. The sheet resistance of Co/Ti multilayer thin film increased by the formation of the amorphous phase at the Co/Ti interface, which decreased by the formation of new crystalline compound CoTi.
This study was based on the evaluation of 9 asphalts that were produced in five major Korean refineries. The study was concentrated to identify the problems of the current asphalt specification (KS M 2201) and to determine the ranges of visco-elastic asphalt behavior. As a conventional asphalt property. asphalt penetration, ring and ball(R&B) softening point, asphalt viscosity, and flash point of asphalt were measured. Also Dynamic Shear Rheometer (DSR) were used to evaluate visco-elastic properties of asphalts in the $-20^{\circ}C$ through $30^{\circ}C$ temperature range. These properties before and after the short-term (RTFO) and long-term (PAV) aging were compared and analyzed to achieve the research objectives. The conclusion from this study can be summarized by the followings. The low temperature rheological behavior of all the straight asphalt from five major Korean refineries is similar regardless of asphalt grade. In the mean while, the rheological behavior at high and intermediate temperature of Korean straight asphalt varies depending on asphalt grade.
Proceedings of the Korean Vacuum Society Conference
/
2000.02a
/
pp.81-81
/
2000
본 연구는 고집적 반도체 소자의 제조 공정에 있어서 산화막을 형성하지 않고 굴곡진 표면을 균일하게 고농도로 도핑하기 위한 방안의 일환으로 기존의 PH3 대신 고체 P를 직접 이용한 2-zone 확산법으로 다결정 Si에 도핑하는 방법을 채택하고, 그 rksmdtjddmdf 검토하는데 목적이 있다. 도핑 시간에 따른 확산 경향을 살펴본 결과, 시간이 증가함에 따라 도핑이 증가하는 뚜렷한 경향을 나타내었으며, 온도가 증가할수록 시간에 따른 농도의 증가량이 커지는 것을 알 수 있었다. 따라서, 고온에 비해 저온에서 더 빨리 pile-up이 일어나며 표면 부근의 농도가 포화상태에 빨리도달하는 것을 알 수 있었다. 다결정 Si에서의 확산거동을 살펴본 결과, 결정립 크기가 적을수록 저항이 높게 나타났으며, 단결정 Si의 저항값보다 약 4~5배 가까이 높은 값을 나타내었다. 또한 동일한 온도에서 시간에 따라 표면 부근의 pile-up 현상이 증가하는 뚜렷한 경향을 보여 주었다. 온도가 감소할수록 pili-up 현상이 증가하는 경향을 나타내었으며, 입계를 통한 빠른 확산에 의해 단결정 Si에 비해 표면 pile-up의 포화가 늦게 일어나는 것을 알 수 있었다. 고체 P를 source로 사용한 경우와 PH3 (phosphine)을 source로 사용한 경우를 비교 분석한 결과, 75$0^{\circ}C$에서 PH3에 비해 고체 P를 사용한 경우의 표면농도가 약 50배 정도로 높게 도핑된 것을 알 수 있었다. 도핑된 P중에서 전기적으로 활성화되어 있는 성분을 알아본 결과, SIMS의 결과와 유사하게 고체 P의 경우가 약 50배 높은 값을 나타내었다. 실제 소자의 특성을 알아보기 위하여 커패시터를 제작하여 측정하여 본 결과, 추가의 도핑을 하지 않은 시편에 비해 고체 P를 도핑한 시편이 약 8%의 Cmin 값의 증가를 보였으며, PH3에 비해 약 3%의 증가된 값을 나타냈었다. 누설전류 특성은 2V에서 수 fA/$\mu\textrm{m}$2로 양호하게 나타났다. 실험 결과 고체 P를 이용한 경우 더 우수한 특성을 나타내었으나, 예상과는 달리 차이가 적게 나타났다. 그 원인은 소자 제조 공정에서 콘택 부분에 큰 저항 성분이 형성되어 생긴 문제로 생각된다. 또한 실험에 사용된 유전체의 두께가 두꺼워 HSG 사이의 갭 부분이 캐패시턴스 증가에 기여를 충분히 못한 것으로 사료된다. 따라서, 제조 공정 상의 문제점을 제거하고 고체 P를 사용할 경우 본 실험에 비해 보다 증진된 특성을 보여줄 것으로 기대된다. 이상의 결론을 토대로 볼 때, 2-zone 확산법을 이용한 P 도핑 방법은 저온에서 효과적으로 다결정 Si에 고농도의 도핑을 할 수 있다고 생각된다.
The present study is intended to comparatively investigate the changes in microstructure and tensile properties at room and elevated temperatures in commercial AM50(Mg-5%Al-0.3%Mn) and 0.3 wt%CaO added ECO-AM50 alloys produced by permanent mould casting. The typical microstructure of AM50 alloy was distinctively characterized using two intermetallic compounds, ${\beta}(Mg_{17}Al_{12})$ and $Al_8Mn_5$, along with ${\alpha}$-(Mg) matrix in an as-cast state. The addition of a small amount of CaO played a role in reducing dendrite cell size and quantity of the ${\beta}$ phase in the AM50 alloy. It is interesting to note that the added CaO introduced a small amount of $Al_2Ca$ adjacent to the ${\beta}$ compounds, and that inhomogeneous enrichment of elemental Ca was observed within the ${\beta}$ phase. The ECO-AM50 alloy showed higher hardness and better YS and UTS at room temperature than did the AM50 alloy, which characteristics can be mainly ascribed to the finer-grained microstructure that originated from the CaO addition. At $175^{\circ}C$, higher levels of YS and UTS and higher elongation were obtained for the ECO-AM50 alloy, demonstrating that even 0.3 wt%CaO addition can be beneficial in promoting the heat resistance of the AM50 alloy. The combinational contributions of enhanced thermal stability of the Ca-containing ${\beta}$ phase and the introduction of a stable $Al_2Ca$ phase with high melting point are thought to be responsible for the improvement of the high temperature tensile properties in the ECO-AM50 alloy.
The formation of high $T_c$ phase is very sluggish and c parameter of unit cell of high $T_c$ phase is about $37{\AA}$. High $T_c$ oxide superconductor with a $T_c$ above 100 K has been successfully prepared by solid state reaction method in BiSrCaCuO system by Pb adding. The microstructure related to the formation of the high $T_c$ phase has been investigated. As compared with YBCO compound, the formation reaction of the high $T_c$ requires long time heat treatment. It is due to the transformation from the low $T_c$ phase to high $T_c$ phase. The sintering just below the melting point of the calcined powder mixture is effective on the formation of the high $T_c$ phase in Pb-added BiSrCaCuO system. The growth of the high $T_c$ superconducting phase has a thin plate shape, which is characterized by the c parameter of $37{\AA}$. The formation of the high $T_c$ phases is delayed by the excessive addition of Pb. The lattice parameter(c) of the unit cell (both the low and high $T_c$ phases) is increased with increase of Pb.
Kimchi, made from seasonal baechu (Chinese cabbage), was sealed in PP trays with a Nylon/CPP lid film and stored at various temperatures (0, 10, $20^{\circ}C$) to investigate the feasibility of detecting its fermentation degree by measuring gas composition inside the packages. The gas composition inside the kimchi package continuously changed due to $CO_2$ evolution during fermentation. Regardless of temperature, the fermentative gas accumulation in the package caused $CO_2$ concentration to increase by two-stepwise pattern, but $O_2$ concentration to decrease exponentially. As $CO_2$ concentration increased secondarily, the pH values of kimchi decreased proportionally (r>0.968). The production of $CO_2$ during kimchi fermentation was stimulated at higher temperatures and affected by seasonal factor. Kimchi made from winter baechu produced more fermentative gas than that from summer baechu. It was suggested that the changes in $CO_2$ concentration could be used as a characteristic index for indicating the fermentation course of packaged kimchi products.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.