• Journal of Energy Engineering
• /
• v.12 no.3
• /
• pp.165-176
• /
• 2003

In this study, the exergy analysis is conducted on the well known performance of already developed system and then compared with the efficiency of each equipment to propose optimum operation of the system. The system used in this study is 500 MW coal firing power plant. The efficiency of the boiler is 67% and the condenser is 99% by exergy analysis. The exergy consumption of the boiler was 32.95% at 100% load. The exergy consumption of the high pressure turbine and the low pressure turbine is 8.31% and 8.12%, respectively. Together with the concrete study on the object of performance revision of the low efficient development system proved in this study, if detailed exergy analysis on the operation condition of the equipments of the development system presently being operated is continued, then it is expected to help minimize the exergy consumption of relatively low efficient parts that are worn-out or miss-installed.

• Journal of computational fluids engineering
• /
• v.17 no.3
• /
• pp.53-58
• /
• 2012

Steady flow simulations through a high pressure turbine guide vanes were carried out. The main objective of the present work is to study the performance of turbulence models on the steady flow prediction from aerodynamic and aerothermal points of view. Three turbulence models were compared, namely SST, k-${\omega}$ and ${\omega}$-Reynolds stress models. The laminar results were also compared. The comparison was done with emphasis on the isentropic Mach number and heat transfer coefficient along the blade, and total pressure loss in the wake region. The calculated isentropic Mach number showed reasonable agreement with experimental data along the blade surface for all three turbulent models. For the total pressure loss in the wake region, ${\omega}$-Reynolds stress model showed the best agreement with the experimental data. However, unless using an appropriate transition model, the heat transfer coefficients of all three turbulent models showed poor agreement with experimental data.

• The KSFM Journal of Fluid Machinery
• /
• v.20 no.2
• /
• pp.17-25
• /
• 2017

Prediction of performance and operating characteristics of a state-of-the-art ultra-supercritical (USC) steam turbine is an important issue in many ways. Theoretical and empirical correlation equations, developed a few decades ago, have been widely used in commercial programs for a prediction of performance. To improve of these correlation equations and apply them to the high pressure turbine of a USC steam turbine, computational fluid dynamic analysis was carried out and correlation equations to calculate efficiency variation of each stage were made. Both fluid dynamic characteristic and thermodynamic performance was analyzed for the development of the correlation equations. In particular, the impact of flow addition through an overload valve (OLV) between stages was examined throughly. The trend of pressure drop due to the flow mixing by the OLV flow addition was analyzed and an efficiency correlation equation considering the OLV flow was also made.

• Journal of Powder Materials
• /
• v.14 no.4
• /
• pp.221-229
• /
• 2007

이상에서 살펴본 바와 같이, 내열재료들은 고밀도를 이용하여 비행하는 물체의 운동에너지를 극대화 시킬 수 있기 때문에 군사적으로 각종 무기체계의 성능 향상에 매우 중요하다. 또한 유도 무기 및 항공기의 경우 고온, 고압 등의 환경에서 운용되기 때문에, 이러한 조건에서 견딜 수 있는 소재 개발이 필수적이다. 따라서 무기 선진국에서는 고밀도 재료인 텅스텐, 몰리브덴, 탄탈륨, 텅스텐-구리 감손우라늄을 활용하기 위한 연구를 활발하게 진행하고 있다. 이중, 텅스텐, 몰리브덴, 텅스텐-구리 라이너에 관한 연구는 괄목할 만한 연구 성과를 거두고 있다. 이러한 연구성과는 기존 탄의 관통 성능을 크게 증가시켜, 이에 대응하고자 하는 방어 체계 연구자들을 바쁘게 할 것으로 판단된다. 한편 내열 금속의 경우, 초고온 및 고압과 같은 극한 환경에서의 고온 강도 및 내삭마성이 우수하기 때문에, 각종 유도 무기 체계의 구성 부품, 즉 터빈, 밸브, 노즐, 제트 베인 등에 적용되고 있으나 대부분의 내열 재료들은 제조 방법이 까다롭고, 가공성이 나쁘며, 고가라는 단점들이 있어 이를 극복하는 연구들이 현재 진행 중에 있다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.3
• /
• pp.20-26
• /
• 2009

Turbopump test for a 30-ton-thrust liquid rocket engine was carried out using real-propellant. Liquid oxygen, kerosene, cold hydrogen gas were used for the oxidizer pump, the fuel pump, and the turbine, respectively. The turbopump was reliably operated at the design and off-design conditions and the performance requirements were satisfied, which implies that the turbopump development at the engine subsystem level is successfully accomplished in the point of performance validation. This paper presents the results of a test where the turbopump was run for 75 seconds at three operating modes. In terms of performance characteristics of pumps and turbine, the results of turbopump assembly test using real-propellant showed a good agreement with those of the turbopump component tests using simulant working fluid.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.864-870
• /
• 2017

The propellants are burned in the pre-burner of the staged combustion cycle engine, and the resulting hot gas drives the turbine, and the turbine operates the turbo pump. The burned gas passing through the turbo pump is supplied to the combustor at high temperature and high pressure, where the gas is supplied in an excess of fuel or an excess of oxidant depending on the amount of fuel or oxidant. When the cycle works at oxidizer-rich staged combustion, its metal pipe can ignite or explode by the impact of even small particles. In this study, we develop the powder combinations for anti-oxidation coating through the analysis of other coating materials and establish the coating process.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.359-365
• /
• 2008

Turbopump test for a 30-ton-thrust liquid rocket engine was carried out using real-propellant. Liquid oxygen, kerosene, cold hydrogen gas were used for the oxidizer pump, the fuel pump, the turbine, respectively. The turbopump was run stably at the design and off-design conditions and the performance requirements were satisfied, which implies that the turbopump development at the engine subsystem level is successfully accomplished in the point of performance validation. This paper presents the results of a test where the turbopump was run for 75 seconds at three operating modes. In terms of performance characteristics of pumps and turbine, the results from turbopump assembly test using real-propellant showed a good agreement with those from the turbopump component tests using simulant working fluid.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.2
• /
• pp.93-101
• /
• 2019

The mechanical properties and microstructure of 1st stage used and casted buckets of $1,100^{\circ}C$ class gas turbine were analyzed to evaluate quality of the components. Gas turbine 1st stage buckets are exposed and operated in the most severe environment except 1st nozzle among the hot path gas components. Additionally, since the 1st stage bucket is a rotating component, so it may cause additional damage to the rear buckets and nozzles which cause a huge financial loss. Therefore, the quality of the casted bucket must be evaluated prior to use at the plant site. In this study, the microstructure analysis and mechanical properties of the casted bucket were evaluated to verify the casting quality and it was confirmed that the quality conditions designed by KEPCO were satisfied. A bucket operated 46% (11,067EOH) of its life time also evaluated for quality comparison.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.5
• /
• pp.125-131
• /
• 2018

Some propellants in a liquid rocket engine are burned in the pre-burner of a staged combustion cycle engine, resulting hot gas drives the turbine. The burned gas passing through the turbine is supplied to the combustor at high temperature and pressure. The form of the gas can be fuel rich or oxidizer rich dependent upon the mixture ratio or the engine scheme. When the cycle works at oxidizer-rich condition, the metal pipes composing the engine can be ignited or even exploded by an impact of very a small particle. In this study, we developed the powder combination and processes for an anti-oxidation coating through the analysis of various coating materials.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.9
• /
• pp.629-641
• /
• 2019

In order to limit the temperature rise of the structure to a certain level or less while maintaining the aerodynamic shape of solid rocket nozzle by effectively blocking a large amount of heat introduced by the combustion gas of high temperature and high pressure, the heat-resistant materials such as C/C composite having excellent ablation resistance are applied to a position in contact with the combustion gas, and the heat-insulating materials having a low thermal diffusivity are applied to the backside thereof. SiC/SiC composite, which has excellent oxidation resistance, is applied to gas turbine engines and contributes to increase engine performance due to light weight and heat-resistant improvement. Scramjet, flying at hypersonic speed, has been studying the development of C/SiC structures using the endothermic fuel as a coolant because the intake air temperature is very high. In this paper, characteristics, application examples, and development trends of various heat-resistant composites used in solid rocket nozzles, gas turbine engines, and ramjet/scramjet propulsions were discussed.