• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.301-306
• /
• 2016

In bridge performance assessments, a new load carrying capacity evaluation model of simple bridges was proposed, which is based on the developed simple support impact factor spectrum. In this paper, a conservative assumption that the inner span with the both ends fixed boundary condition is ideal for applying the impact factor response spectrum for continuous bridges. The impact factor response spectrum has been proposed based on this assumption. The response spectrum by comparing the numerical analysis result and actual measurement data verified the applicability. The analysis was loading the moving load of DB-24 in a six-span continuous bridge, which was the same as the actual measurement data, the dynamic response was measured in the fourth span. The frequency of the bridge was obtained by FFT on the acceleration response and the span-frequency of sample bridge was calculated by the frequency. The impact factor of the sample bridge was determined by applying the span-frequency of the bridge to the proposed response spectrum; it was similar to the result of comparing the actual measured impact factor. Therefore, the method using the impact factor response spectrum based on the frequency response of both ends-fixed beam was found to be applicable to an actual continuous bridge.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.3
• /
• pp.48-57
• /
• 1999

안테나 단에서 직접 수신 신호의 디지털화가 이루어지고 그 해당 신호의 처리는 고속 디지털 신호처리기 내에서 소프트웨어로 수행되는 방식을 SWR(Software Radio)이라 한다. 그러나 현재의 기술 수준을 감안하여 보다 현실적인 SDR(Software Defined Radio) 정의가 필요하게 되었다. SDR이란 수신신호의 디지털화가 안테나 이하의 임의의 단(IF단)에서 이루어지는 무선으로 정의된다. 물론 A/D변환기등의 기술이 더욱 발전되면 궁극적으로는 SWR로 진화될 것이다. 그러면 SDR은 왜 필요한 것일까? 현재 사용중인 이동통신 단말기의 단점은 어느 한 표준 또는 방식에 종속되어 언제 어디서나 임의의 시스템에 접속되어 사용하기에는 많은 기술 종속적인 문제 및 제약을 내포하며, 사용방식에 따른 시스템의 유연성이 없고, 상용 서비스 도중에 발생되는 단말기 문제의 해결(recall service)이 어렵고, 많은 기술료를 지불해야 한다는 것이다. 부연하면 CDMA 셀룰라의 경우 퀄컴 등의 특정한 회사에 의해 기술이 폐쇠되어, 정보의 흐름이 자유스럽지 못할 뿐더러, 이로 인해 기술진화가 보다 빠르게 진행되지 못하고, 전세계적으로 많은 새로운 우수 제품의 출연에 제약이 가해진다는 것이다. 따라서 SDR(Software Defined Radion)을 도입, 하드웨어 및 소프트웨어를 개방형 구조(open architecture)로 개발한다면 정보의 흐름을 자유롭게 할 수 있고, 이로 인하여 세계적으로 다양한 신제품의 개발이 촉진되고 결과적으로 전세계 시장이 커지게 되는 일석이조의 효과를 얻을 수 있게 된다. 또한 이 같은 개방형 단말기 개발의 필요성은 최근 시장동향으로 볼 때, 기존의 단말기 회사 입장에서는 새로운 수익 모델이 필요한 시점이고, 또한 2002년경에 판매되는 단말기의 80%정도는 멀티모드타입 단말기일 것으로 예측되는 점, 그리고 금년말까지 100개 회사 이상이 SDR 포럼 멤버로 가입할 것으로 예측되는 점, 무선 인터넷 폭발적인 성장으로 복합 멀티미디어 단말기 시대가 다가오는 점 등으로 미루어 볼 때, 고객의 서비스 가치선택에 역점을 둔 기술을 중시해야 한다는 점에서 더욱 설득력을 지닌다. 따라서 이 같은 목적과 3세대 이동통신 및 인터넷 사용자의 증가, 반도체기술의 발전에 힘입어, 과거 군용 시스템에서 이용되던 SWR 기술을 상용시스템 특히 3세대 이동통신에 적용하려는 연구가 활발히 진행되고 있다. '96년 SDR 포럼이 결성되었는데, 목적은 휴대형 장치(hand-held devices), 기지국(base stations), 차량형 장치(mobile stations)를 포함하는 다중모드(multi-mode), 다중대역(multi-band) SDR을 위한 개방형 구조의 표준을 정하기 위함이다. 이 같이 public forum에 의한 표준(open architecture standard)이 정해지면 그 다음은 이를 어떻게 구현할 것인가가 문제가 될 것이다. 본고에서는 먼저 SDR 단말기 요구사항을 살펴보고, 이 요구사항들을 만족하는 SDR 단말기 구조, SDR 계층참조 모델, 그리고 기존의 단말기 구조와 SDR 계층참조 모델의 연관관계에 대해 살펴보고, 크게 두가지 종류의 단말기 즉 사용 SDR 단말기와 군용 SDR 단말기에 대해 살펴보고, 설계 절차 및 현재 시점에서 단말기 구현을 위해 해결해야 하는 기술적 과제를 살펴보고 결론을 언급한다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.04a
• /
• pp.94-99
• /
• 1994

최근 인구의 과밀화와 이에 따른 지가의 상승 등으로 대표적인 주거용 빌딩인 아파트의 고층화가 급속하게 진행되고 있고 아파트에 설치되는 엘리베이터도 점차 대형화, 고속화 되고 있다. 실례로 15층 아파트의 경우 11인승, 60m/min의 엘리베이터가 일반적으로 사용되는 반면, 20층 아파트의 경우 17인승, 90m/min이 주로 사용된다. 이와 같이 엘리베이터의 용량과 운행 속도가 증가함에 따라 필연적으로 소음 및 진동 문제가 발생하게 된다. 특히 아파트의 경우 침실, 공부방 등 고도의 정숙을 요하는 생활 공간이 많고, 내부 공간의 활용도를 높이기 위하여 이들 방들이 엘리베이터 기계실 또는 운행 통로와 직접 접하여 있는 경우도 있어 이 경우 소음, 진동 문제는 아주 심각한 문제로 대두된다. 본 연구소가 측정한 방에 의하면 S신도시 L아파트의 경우 아파트 최상층 방에서 실내 소음도가 46dB(A), 벽의 진동가속도가 3.4mm/s$^{2}$(RMS)으로 나타났다. 진동의 경우 생활에 직접적인 악영향을 미칠 수준은 아니지만 소음의 경우 ASHRAE 권장 주택소음 기준치가 35dB(A) 이하임ㅇㄹ 감안하면 주거에 곤란한 수준이다. 수년전, 고층 아파트가 보급될 초기에는 아파트에 엘리베이터가 설치되어있다는 그 자체만으로 충분한 장점이 되어 다소음 소음, 진동문제는 큰 불만거리가 되지 않았지만 엘리베이터가 보편화된 지금에는 엘리베이터의 편리성만으로는 점점더 크게 요구되는 정숙성이 보상되지 않는다. 따라서 전반적인 아파트의 소음, 진동 문제에 큰 비중을 차지하는 엘리베이터에 의한 소음, 진동에 관하여 체계적인 연구가 필요하다. 이에 본고에서는 엘리베이터에 의한 아파트의 소음 및 진동에 관하여 그 현황, 원인 그리고 대책에 관한여 논하고자 한다.감 방법을 연구하였고, T.Sakai는 5자유도 모델을 이용하여 엔진 공회전시 발생하는 치타음에 대해 이론과 실험을 통해 해석하고, 엔진 회전수 변동, 클러치 특성, 변속기의 드래그(drag) 토크의 영향과 치타음 저감을 위한 개선된 클러치 특성을 제시하였다. 이 외에도 Thomas C.T.와 E.P.Petkus는 특정 차량에 대한 동력전달계의 비틀림 진동 현상에 대해 연구하였다. 이러한 연구들로 볼 때, 자동차 동력전달계에서 발생하는 진동은 이론과 실험을 통해 그 해석이 가능하며 설계에 매우 유용하게 이용되고 있음을 알 수 있다. 따라서, 본 연구는 4 실린더 4 싸이클 1.5 L 엔진을 장착한 경승용차의 실차 주행실험을 통해 가속 페달의 급조작에 따른 차체의 종진동 현상을 측정하고, 엔진-변속기-타이어-차체의 반환정계 4자유도 진동모델로 시뮬레이션을 수행하여 실차 주행실험의 결과치와 비교, 분석한 후 클러치 비틀림 특성을 비롯한 자동차 동력전달계의 각 설계인자들이 차체의 종진동에 어떠한 영향을 미치는가를 해석하고자 한다.be presented.LIFO, 우선 순위 방식등을 선택할 수 있도록 확장하였다. SIMPLE는 자료구조 및 프로그램이 공개되어 있으므로 프로그래머가 원하는 기능을 쉽게 추가할 수 있는 장점도 있다. 아울러 SMPLE에서 새로이 추가된 자료구조와 함수 및 설비제어 방식등을 활용하여 실제 중형급 시스템에 대한 시뮬레이션 구현과 시스템 분석의 예를 보인다._3$", chain segment, with the activation energy of carriers from the shallow trap with 0.4[eV], in he amorphous regions.의 증발산율은 우기의 기상자료를 이용하여 구한 결과 0.05 - 0.1

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1330-1336
• /
• 2007

The purpose of the study was to verify deduction of each coefficient necessary to analysis on micro-pressure waves and reliability of the analysis result. The tunnel running train model testing device used in the test was manufactured by scale of 1:60 and the study used a train model with ten cars long according to specifications of KTX model. The study applied tunnels with cross sections of $107.9m^3\;and\;95.1m^3$ and applied tunnel extensions with 1km, 0.75km and 0.5km. Also, the study tested train speed by changing it into 275, 300, 325 and 350km/h. The test device was a hydraulic launch system composed of a train model, a hydraulic launcher, a tunnel model and a brake. The study measured speed of a model trainby a speed sensor installed in the point of each 1.2m from the front of tunnel entrance and a pithead of tunnel exit and measured pressure change of internal tunnel continuously by installing pressure sensors in the entrance part of tunnel, in the middle part of tunnel and in the exit part of tunnel. As the result of the measurement, it was known that pressure slope of pressure wave happened in the entrance part of tunnel was increased by a nonlinear effect while spreading the tunnel or its pressure slope was reduced by diffusion. Also, the study compared and analyzed micro-pressure waves happened in the exit part of the tunnel by installing each kind of hoods in the entrance part of the tunnel to prevent reduction of micro-pressure waves.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.9
• /
• pp.19-28
• /
• 2014

Recently, the proportion of long tunnel has increased for efficient use of land due to limited land area, driving convenience and high speed. RMR and Q-System of empirical methods has been mainly used for tunnel support design in domestic. Although shotcrete is the key to NATM tunnel, the related studies are insufficient. So, steel fiber reinforced shotcrete is applied to II~V grade rocks on domestic and foreign applications. And same amount of shotcrete is equally applied to tunnel roof and wall regardless of the applied rock load. Shotcrete is applied excessively rather than the original proposed value of RMR and Q-System. Thus, this study is to reevaluate the application part of plain shotcrete and steel fiber reinforced shotcrete of tunnel in Daebo granite, and to propose the reasonable application method of steel fiber reinforced shotcrete. Field test and numerical back analysis using measurements were performed to verify stability. According to results, if RMR values are the upper class in the III grade, it can be designed in accordance with upper grade. In addition, if rock condition is good as a mountain tunnel in Daebo granite, it can be applied for plain shotcrete to III grade rocks because there is also no stability problems. And although steel fiber reinforced shotcrete is applied only crown of the tunnel in IV grade rocks, it is possible to secure stability for falling rock by key-block.

• Journal of Korean Society for Geospatial Information Science
• /
• v.25 no.2
• /
• pp.31-37
• /
• 2017

Recently, governmental authority and local government are looking for a method of utilizing location information of smart phone for urgent rescue in fire and kidnap situation. Under this background, in this study, a method of rapidly collecting, constructing location determination based Wi-Fi AP data utilizing location information of smart phone and mobile mapping system was suggested in order to construct precise positioning information that could be utilized under urgent situation. By performing compensation work for GPS/INS/DMI through collected outcome, position of collected vehicle was acquired. In addition, source data integrating Wi-Fi information and collected position by coupling based on Wi-Fi AP collector and GPS time was constructed and Wi-Fi radiomap was constructed by removing Wi-Fi signal noise that reduces precise position performance. As a result of performing location determination performance assess ment by selecting 10 test positions by each local government, result value of 25.46cm for total local government average and 27.76m for SD could be obtained. It is considered that this result could be utilized as a technology of being able to supplement or substituting GPS location determination technology that is impossible in plocation determination of mobile communication company's base station (200m~2km) and indoor being used at present.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.37-45
• /
• 2018

An electric vehicle is an environmentally friendly vehicle because there is no exhaust gas, unlike gasoline automobiles. On the other hand, because the electric vehicle is driven by electric power charged in batteries, the distance to go through a single charge depends on the energy density of the batteries. Therefore, a lithium-ion battery with a high energy density is a good candidate for batteries in electric vehicles. Because the electrode is an essential component that governs the efficiency of a lithium-ion battery, the electrode manufacturing process plays a vital role in the entire production process of lithium-ion batteries. In particular, the drying process during the electrode manufacturing process is a critical process that has a significant influence on the performance. This paper proposes an innovative process for improving the efficiency and productivity of the drying process in electrode manufacturing and describe the equipment design method and development results. In particular, the design procedure and development method for enhancing the electrode adhesion power, atmospheric pressure superheated steam drying technology, and drying furnace slimming technologies are presented. As a result, high-speed drying technology was developed for battery electrodes through the world's first turbo dryer technology for mass production using open/integrated atmospheric pressure superheated steam. Compared to the conventional drying process, the drying furnace improved the productivity (Dry Lead Time $0.7min{\rightarrow}0.5min$).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.8
• /
• pp.352-362
• /
• 2016

Today, it appears that the rapid advances in technology have allowed broadening both the system technology and the business opportunities in the rail industry. Owing to the developments in technology and the industry, and also due to the hearth, the latest high-speed trains and a variety of unattended operations in rail systems are being developed and are operational. In particular, this study covers the existing railway rolling stock and signaling systems that operate in an environment more complex than the concept of localized management, so the introduction of a new signaling system is needed. In addition, developments based on the existing signal system concepts for passenger railways need to minimize human injury. In this study, to participate in the development of new systems in a variety of domains and to provide an integrated common vision methodology as an engineer on the basis of efficient signal system design and safety would like to present the methodology for action. Therefore, each different linkage through the next new domain zone system design: design through to secure the integrity of safety than can secure methodology.

• Journal of Environmental Impact Assessment
• /
• v.25 no.3
• /
• pp.175-189
• /
• 2016

The guideline for railway noise mapping is notificated in the administration law for noise/vibration which is announced by the ministry of environment, Korea. Here input parameters for the railway sound sources are proposed for each prediction models. In case of the application of the vehicle characteristics it is suggested to choose "0(%)" for the disc brake parameter. However new trains have been in revenue service since the announcement of the guideline, an investigation of the effect of the input parameters of the foreign railway prediction models on the prediction results of korean railway systems are needed. In this paper the sound prediction results are analyzed with a focus on the input parameters such as disc brake percentage, rail roughness, rail joints. Schall03 is used for the railway noise prediction which has been using most frequently in Korea. The results are shown and discussed.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.19 no.5
• /
• pp.40-51
• /
• 2020

Much time has passed since Korea's expressway congestion-threshold speed was revised in 2011. In the meantime, various expressway environments have changed owing to improved performance of vehicles, expanded operations of transport competition (i.e., the KTX), and increased speed limits along some expressway sections. In addition, the speed that expressway users expect to travel at is also increasing. Therefore, through a survey, this study investigates expressway users' perceptions of congestion, and reviews the adjustment of the expressway speed congestion threshold by analyzing expressway traffic flow. One result of the survey confirms that the threshold speed expressway users consider to be congestion has slightly increased. Analyzing traffic and speed data through a K-means algorithm found that the threshold speed for congestion is 60 km/h. In addition, assuming the congestion threshold speed increase from 40 km/h to 50 km/h and 60 km/h, frequently congested expressway sections are identified, determining that 50 km/h is appropriate as a congestion threshold for proper expressway mobility management.