• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.7
• /
• pp.619-626
• /
• 2007

The analysis of the frictional energy of the rubber block with contact to the surface is necessary to study the wear for rubber. It is important to define the relationship of the frictional energy and wear, as the most theory of the wear of rubber product is based on the frictional energy of rubber block. To predict the life of the rubber block, the most of research has been focused on the use of the finite element analysis or the actual experiments which need the many time and expensive costs.Therefore, this research is achieved the successful results of the analysis to the frictional energy by analytic method. This frictional energy is function of the material properties, the shape of block, the vertical and horizontal load and the block moving speed. The analytical results are compared with the test results of this paper which can be used for the analysis of the friction behavior for the wear estimation of the rubber products.

• Journal of the Korean Chemical Society
• /
• v.54 no.6
• /
• pp.749-754
• /
• 2010

In this study, rubber vulcanization property, change in physical property, morphology and chemical characteristics of blended rubber depending on various IR/CR ratio were investigated for the purpose of the improvement of material property and durability. The effect of surface treatment by chlorine on the friction coefficient was also studied with various conditions of surface treatment. In terms of vulcanization property, as the amount of CR content increased, the speed of cure was decreased, while the density of crosslinking stayed constant. It means hardness and modulus were increased as the CR content increased. It is related to change in cure property and mechanical strength was improved by the effect of crystallization reaction. In the aging property, as the CR content increases, the changed amount of basic properties were decreased, which acts as a reducing factor in change of aged property by complementing weak point in mechanical property. It was found that the degree of property change for surface treated samples were reduced. According to the microscopic result, the degree of surface dispersion on rubber blends was increased by increasing CR content. Rubber surface showed uniform direction in pattern with increased smoothness and luster by treatment with chlorine. The degree of rubber reforming was measured by the remaining amount of chlorine and the friction coefficient was dependent on the amount of chlorine combined with rubber. In the initial stage of surface treatment, from 10 to 40 phr, the friction coefficient of specimen was rapidly reduced. However, as the concentration of chlorine solution increased, the change in friction coefficient was decreased.

• Elastomers and Composites
• /
• v.35 no.3
• /
• pp.180-187
• /
• 2000

For the purpose of developing a new type of frictional material using scrap rubber in which rubber makes continuous phase, potassium titanate($K_2Ti_6O_{13}$) was synthesized and added to rubber matrix. Needle-typed $K_2Ti_6O_{13}$ powders were obtained through the flux method using KCI salt and excess $K_2CO_3$. It was also found that the powders should be surface-treated to enhance adhesion and 10 phr of epoxy be added for the physical properties of the rubber composite.

• Elastomers and Composites
• /
• v.49 no.2
• /
• pp.149-154
• /
• 2014

Friction and abrasion behaviors were investigated for SBR rubber compounds reinforced by silica and carbon black. Knife-blade abrader, newly designed based on tearing energy theory, was utilized in order to evaluate the effect of frictional work on the wear rate of the rubber compounds. It was found that the power law relation between frictional work and wear rate worked, in which as the wear rate was increased as frictional work increased. The wear rate could be determined successfully using the knife-blade abrader in which a moving distance of the knife blade in the process of wearing was measured continuously, instead of intermittent measurements of weight loss by wear during experiment.

• Elastomers and Composites
• /
• v.45 no.4
• /
• pp.280-285
• /
• 2010

The CIIR blends with SBR, NBR and BR were prepared with various mixing ratios. The mechanical and physical properties of these blends, such as frictional coefficient, abrasion resistance, compression set, and specific gravity, were measured. In the permanent compression set measurement, the blends at the composition of 75 wt% CIIR showed the highest value, which means the lowest resistance to deformation. As SBR, NBR and BR blends with CIIR, the coefficient of friction of the mixtures showed a tendency to decrease in arithmetic average. In the case of blending CIIR with BR in order to increase the friction force, the negative effect due to reduction in abrasion resistance was greater than the positive effect of the improvement of the traction force caused by increasing friction coefficient.

• Composites Research
• /
• v.19 no.6
• /
• pp.16-22
• /
• 2006

The puncture properties under various conditions were investigated for the optimum conditions to yield the best properties. Fiber aspect ratio(AR: length of fiber/diameter of fiber), interphase condition and fiber content were considered as variables which impact the puncture force and friction force. The puncture force of short-fiber reinforced rubber increases up to 3.4 times compared to the virgin material. The better interphase condition shows the higher puncture force at given fiber AR and fiber content. The friction force of the matrix and reinforced rubber with a fiber AR below 155 does not exist. The friction force of the reinforced rubber with the good interphase condition and high fiber AR is higher than puncture force of matrix. Overall, it was found that the interphase condition, fiber AR and fiber content have an important effect on the puncture properties.

• The tire
• /
• s.2
• /
• pp.21-29
• /
• 1967

• Korea lubricating oil industries association bulletin
• /
• no.47
• /
• pp.4-14
• /
• 1991

• Elastomers and Composites
• /
• v.49 no.1
• /
• pp.73-81
• /
• 2014

Friction and wear behaviors of natural rubber(NR) compounds were investigated using a blade-type abrader. The effects of temperature, normal load, and rotation speed on wear rate were studied, and wear behaviors of deteriorated compounds were also evaluated. As the rotation speed of specimen and the normal load to specimen increased, the wear rate increased. However, as the experimental temperature increased, the frictional coefficient decreased and the wear rate decreased accordingly. It was found from the wear studies that a power-law relation works between the frictional work input and the wear rate. It was observed that the wear rate dramatically increased by the degradation of the rubber specimen. The wear pattern was developed and the bigger ridge space of the pattern was observed usually in the higher normal load applied. In determining the wear rate of rubber compound, the continuous measurements of wear distance using the blade-type abrader could be successfully used instead of intermittent measurements of wear-loss weight.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3292-3297
• /
• 2014

The vehicle wiper blade(W/B) to lower the friction coefficient of the rubber surface after the surface treatment with chlorine were investigated. IR spectrum from W/B was used to determine the extent of chlorination of the rubber surface. Coefficient of friction is significantly reduced by the treatment with chlorine. In particular, the more sensitive influence on the initial chlorination. Rubber surface properties with respect to the longitudinal direction of the cutting plane were obtained by EPMA line analysis results. Penetration depth by EPMA chlorine concentration($20.0{\ell}$ of water for 35.0% hydrochloric acid(HCl) $300m{\ell}$ with 5.25% sodium hypochlorite(NaOCl) $400m{\ell}$), the chlorine treatment for 5 minutes was conducted to find that after 1.2 ${\mu}m$.