• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.49-54
• /
• 1991

In this study the correlation between material constants and microwave absorbing characteristics of ferroxplana composite microwave absorber used in X-band was investigated. The real part of permeability(${\mu}_{r}'$) was decreased and the imaginary part of permeability(${\mu}_{r}"$) of ferroxplana composite was increased with increaing ferroxplana loading ratio(F/R). The frequency showing maximum attenuation was shifted to lower frequency with increasing absorber thickness. The absorber 2.6 mm thick showed good band width property and 3.2 mm thick showed good attenuation property. From the apphcation of ferroxplana composite's material constants to the region of material constants which satisfy broad band width, it is found that the absorbing characteristics were estimated quantitatively. Estabhshment of material constants' region which satisfies broad band width can make practical application to design of high performance ferrite microwave absorber.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.1
• /
• pp.108-115
• /
• 2019

The thermal response of elastomeric insulators used as protection against high-temperature and high-pressure combustion gases varies depending on their composition and thermal environment conditions. In this paper, the thermal response characteristics of elastomeric insulators in different mixing environments were compared. Tests to determine thermal protection performance were carried out using a thermal protection rubber evaluation motor(TPREM), combustion gas velocities of 20 m/s and 100 m/s were tested at a chamber pressure of 1,000 psig. The pressure time curve of the chamber, the temperature time curve of the internal materials, the residual thickness and the thermal destruction depth of the test specimens were obtained. The results showed that the thermal protection performance of elastomeric insulators in different mixing environments was similar.

• Journal of Adhesion and Interface
• /
• v.22 no.4
• /
• pp.118-127
• /
• 2021

In this study, the mechanical properties of vulcanized rubber were evaluated through compounding by controlling filler content to improve the mechanical properties of NBR rubber. Aramid and glass fibers with excellent heat resistance were used as fillers, and ceramics were additionally used in anticipation of a complementary effect, and as for the ceramic materials, needle-shaped and plate-shaped ceramics were used. Each filler was used in an amount of 5.0, 10.0, 15.0, and 20.0 phr in order to investigate the basic properties according to the amount of filler. To confirm the complementary effect through ceramic application, each 10.0 phr fiber and ceramic were mixed with 1:1 ratio to evaluate mechanical properties. As a result, it was confirmed that the decreasing ratio of tensile strength after heat aging was small in the order of aramid fiber, acicular ceramic, glass fiber, and plate ceramic in the case of applying the filler alone. In addition, the mechanical characteristics of vulcanized rubber using composite filler based on fibers and ceramics were evaluated, and it was confirmed that the composite filler had a complementary effect on thermal aging.

• Elastomers and Composites
• /
• v.10 no.2
• /
• pp.136-156
• /
• 1975

고무는 불량열전도체(不良熱傳導體)이며 두께가 두꺼우면 내부(內部)가 적정온도수준(適正溫度水準)에 이르기 전까지 가황시간(加黃時間)이 길어진다. 가황온도(加黃溫度)가 상승(上昇)할수록 가황물(加黃物)의 물성(物性)은 열화(劣化)되는 경향(傾向이) 있다. 천연(天然)고무든지 합성(合成)고무든지 간(間)에 과가황(過加黃)에 대(對)한 저항성(抵抗性)이 나쁘므로 특(特)히 고온가황(高溫加黃)에 대(對)해 민감(敏感)하다. 이것은 고온(高溫)에서 단시간(短時間) 가황(加黃)일수록 가속(加速)된다. 평탄가황배합물(平坦加黃配合物)의 경우에서 보더라도 내부(內部)가 적절(適切)히 가황(加黃)되기도 전(前)에 외부(外部)는 과가황(過加黃)이 되는 수가 있다. 근래(近來) 발간(發刊)된 문헌(文獻)에서도 이러한 내용(內容)이 잘 설명(說明)이 되어 있는데 다른 각도(角度)에서 고찰(考察)해 볼것 같으면 정체시간(停滯時間)이 비교적(比較的) 길지 않는 한(限) 가황시간(加黃時間)은 정체시간(停滯時間)과 sheet 가황시간(加黃時間)과의 합(合)이라고 말할 수 있겠다. 예(例)를 들어 설명(說明)하자면 $130^{\circ}C(266^{\circ}F)$에서 정체시간(停滯時間)이 10분(分)이고 sheet 가황시간(加黃時間)이 20분(分)인 제품(製品)은 이 온도(溫度)에서 30분간(分間) 가황(加黃)해야 된다는 것이다. 온도계수(溫度係數)를 2라고 가정(假定)할 경우 $140^{\circ}C(284^{\circ}F)$에서의 가황시간(加黃時間)은 $30\times\frac{1}{2}=15$분(分)이 아니라 $20\times\frac{1}{2}+10=20$분(分)이 된다. 크기가 큰 제품(製品)은 보통(普通) 다음에 있는 여러 방법(方法)들 가운데 한 가지 또는 여러가지를 조합(組合)하여 가황(加黃)시킨다. a) 크기가 작은 것에 대한 것 보다 낮은 온도(溫度)에서 가황(加黃)한다. b) 침투가황-제품(浸透加黃-製品)을 가압하(加壓下)에 두고서 외부가황(外部加黃)은 단속(斷續)시키고 열(熱)이 중심(中心)으로 침투(浸透)하게 한다. c) 단계가황(段階加黃)-처음에는 저온(低溫)에서 시작(始作)하여 일정간격(一定間隔)을 두고 점차(漸次) 온도(溫度)를 상승(上昇)시켜 최종적(最終的)으로 가황온도(加黃溫度)까지 올린다. d) 가능(可能)하다면 metal base나 금형(金型)에서 고무를 증기가황(蒸氣加黃)시킬 경우에 있어서 속이 빈 축(軸)을 사용하여 내부(內部)로 부터 가열(加熱)하면 가황시간(加黃時間)이 단축(短縮)된다. e) 냉각중(冷却中)의 후가황(後加黃)-이것은 가열장치(加熱裝置)에서 끄집어낸 후 제품(製品)의 외부(外部)를 냉각(冷却)시키는 방법(方法)이다. 가열(加熱)된 제품(製品)이 쌓여 있거나 적절(適切)하게 냉각(冷却)되지 않을 때 가황(加黃)이 추가적(追加的)으로 되거나 과가황(過加黃)이 될 우려가 있는 제조공정(製造工程)에서는 흔히들 이 방법(方法)을 무시(無視)하고 있다. 여기서 강조(强調)해 두어야 할 것은 항상 제품(製品)의 외부(外部)를 완전(完全)히 가황(加黃)시킬 필요(必要)는 없다는 것이다. 다공성(多孔性)이나 기포생성(氣泡生成)을 조장(助長)하는 불량가황상태(不良加黃狀態)와 표면(表面)에서의 과가황상태간(過加黃狀態間)의 균형(均衡)을 취(取)해 줘야 하는데 물론(勿論) 이때는 가황시간(加黃時間)을 단축(短縮)시켜야 한다는 경제적(經濟的)인 측면(側面)도 아울러 고려(考慮)해야 한다. 이것은 고무기술자(技術者)가 당면(當面)해야할 과제(課題)에 속(屬)하며 바람직 한것은 본장(本章)의 내용(內容)이 여러 상황하(狀況下)에서 당면(當面)한 문제(問題)에 대(對)해 어떻게 대처(對處)해 야 할지를 모르는 여러 기술자(技術者)들에게 도움이 되었으면 하는 것이다.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.1
• /
• pp.90-98
• /
• 1999

For the control of vibration and noise of metal structures having relatively low damping, viscoelastic materials are widely used and usually attached at metal structures with an additional constraining layer to secure them. The damping and elastic properties of structures having constrained viscoelastic material layers are dependent on not only temperature and frequency but also their thicknesses. Hence, optimal design of the thicknesses of viscoelastic and constraining layers for a certain base structure are very important to maximize their efficiency and to lighten their weight. In this study, the variation of loss factor of beams having a constrained viscoelastic layer according to the change of thickness has been carefully investigated. From these, optimal design method of the minimum thickness beam having a given loss factor is suggested and numerically verified for a real beam.

• Journal of the Korean Magnetics Society
• /
• v.14 no.4
• /
• pp.131-137
• /
• 2004

For the aim of thin electromagnetic wave absorbers used in mobile telecommunication frequency band (0.8-2.0㎓), we investigate high-frequency magnetic, dielectric and microwave absorbing properties of iron particles dispersed in rubber matrix in this study. The major experimental variables are particle shape (sphere and flake) and initial particle size (in the range 5-70 $\mu\textrm{m}$) of iron powders. High value of magnetic permeability and dielectric permittivity can be obtained in the composites containing thin plate-shape (flake) iron particles (of which thickness is less than skin depth in ㎓frequency), which can be produced by mechanical forging of spherical iron powders using an attrition mill. This result is attributed to the reduction of eddy current loss (increase of permeability) and the increase of space charge polarization (increase of permeability). The optimum initial particle size is found to be about 10 $\mu\textrm{m}$ for the attainment of the material parameters (particularly, real part of complex permeability) satisfying the wave impedance matching. With the iron powders controlled in size and shape as absorbent fillers in rubber matrix, the thickness can be reduced to about 0.7mm with respect to -5㏈ reflection loss (70% power absorption) in mobile telecommunication frequency band.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.330-342
• /
• 1998

The effect of rubber mold on densification behavior of pure iron powder was investigated under cold isostatic pressing. The thickness effect of rubber mold was also studied. The elastoplastic constitutive equation based on the yield function of Shima and Oyane was implemented into the finite element program(ABAQUS) to predict compaction responses of metal powder under cold isostatic pressing. The hyperelastic constitutive equation based on Moony-Rivlin and Ogden strain energy potentials was also employed to analyze deformation of rubber mold. The coefficients of the strain energy potentials were obtained from tension and volumetric compression data of rubber. Finite element results were compared with experimental data for densification of pure iron powder under cold isostatic pressing.

• Journal of Sericultural and Entomological Science
• /
• v.31 no.2
• /
• pp.113-120
• /
• 1989

A new microsporidia (S85) was isolated from the silkworm, Bombyx mori L. in Suwon, Korea in 1985. The electron microscopic observation of the fine structure of the spore was studied for the characterization of the new microsporidia and its taxonomic position. The sporewall was composed of three different electron dense layers and the spore surface was rouph and wrinkled. The polaroplast has two parts which differed in the arrangement of the lamellae. The polarfilament was isofilar with thirteen coils and it was consisted of eight concentric layers of different electron density. The spore contained a single nucleus and the pansporoblast appeared as a thin ballon-like structure surrounding the spore. The membrane was generally smooth and shown occationally wrinkled.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.10
• /
• pp.1297-1303
• /
• 2013

A nonlinear finite element analysis is performed to evaluate the sealing capability and stress of dust covers for the ball joint of an automotive steering system. The analysis is performed for two types of dust covers: wrinkle type and pot type. The assembly condition and operation condition are analyzed, and the maximum stress and contact normal stress at the ribs are evaluated. It is confirmed that the sealing capability of both types is fairly good, but the wrinkle type is better than the pot type in terms of the maximum stress.

• Polymer(Korea)
• /
• v.27 no.6
• /
• pp.589-595
• /
• 2003

Unsaturated polyester (UP) nanocomposite with montmorillonite (MMT) which contains different types of organic modifiers far nano-filler have been prepared to investigate the effect of chemical structure of organic modifiers and mixing time of all components on properties of products. It was found that the morphology and various physical properties of UP/MMT nanocomposites were influenced by properties of organic modifiers of MMTs. It was also confirmed that the content of MMT does not significantly affect properties of UP/MMT nanocomposites.