• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.300-305
• /
• 2013

Part shrinkage in injection molding is inevitable phenomenon. Thus, it is necessary not only study on the reducing part shrinkage but characterization of part shrinkage. In this study, part shrinkage in injection molded 2.5 dimensional annular shaped specimens has been studied using glass fiber reinforced PC. Annular shaped specimens were designed with various sizes of outer diameter and thickness. Injection temperature, packing time and packing pressure were selected for operational conditions. Profile variations of outer and inner diameters of molded specimens for various operational conditions were investigated. Sizes of outer and inner diameters of injection molded specimens were smaller than the sizes of mold. Part shrinkage decreased as outer diameter and thickness increased. Part shrinkage showed anisotropic behavior and it depended upon gate location. Subsequently, molded specimens were not circular but oval in shape, and showed the largest shrinkage in the direction of gate. It was realized that the mold design such as gate design is important to control the shape of molded products.

• Elastomers and Composites
• /
• v.10 no.2
• /
• pp.136-156
• /
• 1975

고무는 불량열전도체(不良熱傳導體)이며 두께가 두꺼우면 내부(內部)가 적정온도수준(適正溫度水準)에 이르기 전까지 가황시간(加黃時間)이 길어진다. 가황온도(加黃溫度)가 상승(上昇)할수록 가황물(加黃物)의 물성(物性)은 열화(劣化)되는 경향(傾向이) 있다. 천연(天然)고무든지 합성(合成)고무든지 간(間)에 과가황(過加黃)에 대(對)한 저항성(抵抗性)이 나쁘므로 특(特)히 고온가황(高溫加黃)에 대(對)해 민감(敏感)하다. 이것은 고온(高溫)에서 단시간(短時間) 가황(加黃)일수록 가속(加速)된다. 평탄가황배합물(平坦加黃配合物)의 경우에서 보더라도 내부(內部)가 적절(適切)히 가황(加黃)되기도 전(前)에 외부(外部)는 과가황(過加黃)이 되는 수가 있다. 근래(近來) 발간(發刊)된 문헌(文獻)에서도 이러한 내용(內容)이 잘 설명(說明)이 되어 있는데 다른 각도(角度)에서 고찰(考察)해 볼것 같으면 정체시간(停滯時間)이 비교적(比較的) 길지 않는 한(限) 가황시간(加黃時間)은 정체시간(停滯時間)과 sheet 가황시간(加黃時間)과의 합(合)이라고 말할 수 있겠다. 예(例)를 들어 설명(說明)하자면 $130^{\circ}C(266^{\circ}F)$에서 정체시간(停滯時間)이 10분(分)이고 sheet 가황시간(加黃時間)이 20분(分)인 제품(製品)은 이 온도(溫度)에서 30분간(分間) 가황(加黃)해야 된다는 것이다. 온도계수(溫度係數)를 2라고 가정(假定)할 경우 $140^{\circ}C(284^{\circ}F)$에서의 가황시간(加黃時間)은 $30\times\frac{1}{2}=15$분(分)이 아니라 $20\times\frac{1}{2}+10=20$분(分)이 된다. 크기가 큰 제품(製品)은 보통(普通) 다음에 있는 여러 방법(方法)들 가운데 한 가지 또는 여러가지를 조합(組合)하여 가황(加黃)시킨다. a) 크기가 작은 것에 대한 것 보다 낮은 온도(溫度)에서 가황(加黃)한다. b) 침투가황-제품(浸透加黃-製品)을 가압하(加壓下)에 두고서 외부가황(外部加黃)은 단속(斷續)시키고 열(熱)이 중심(中心)으로 침투(浸透)하게 한다. c) 단계가황(段階加黃)-처음에는 저온(低溫)에서 시작(始作)하여 일정간격(一定間隔)을 두고 점차(漸次) 온도(溫度)를 상승(上昇)시켜 최종적(最終的)으로 가황온도(加黃溫度)까지 올린다. d) 가능(可能)하다면 metal base나 금형(金型)에서 고무를 증기가황(蒸氣加黃)시킬 경우에 있어서 속이 빈 축(軸)을 사용하여 내부(內部)로 부터 가열(加熱)하면 가황시간(加黃時間)이 단축(短縮)된다. e) 냉각중(冷却中)의 후가황(後加黃)-이것은 가열장치(加熱裝置)에서 끄집어낸 후 제품(製品)의 외부(外部)를 냉각(冷却)시키는 방법(方法)이다. 가열(加熱)된 제품(製品)이 쌓여 있거나 적절(適切)하게 냉각(冷却)되지 않을 때 가황(加黃)이 추가적(追加的)으로 되거나 과가황(過加黃)이 될 우려가 있는 제조공정(製造工程)에서는 흔히들 이 방법(方法)을 무시(無視)하고 있다. 여기서 강조(强調)해 두어야 할 것은 항상 제품(製品)의 외부(外部)를 완전(完全)히 가황(加黃)시킬 필요(必要)는 없다는 것이다. 다공성(多孔性)이나 기포생성(氣泡生成)을 조장(助長)하는 불량가황상태(不良加黃狀態)와 표면(表面)에서의 과가황상태간(過加黃狀態間)의 균형(均衡)을 취(取)해 줘야 하는데 물론(勿論) 이때는 가황시간(加黃時間)을 단축(短縮)시켜야 한다는 경제적(經濟的)인 측면(側面)도 아울러 고려(考慮)해야 한다. 이것은 고무기술자(技術者)가 당면(當面)해야할 과제(課題)에 속(屬)하며 바람직 한것은 본장(本章)의 내용(內容)이 여러 상황하(狀況下)에서 당면(當面)한 문제(問題)에 대(對)해 어떻게 대처(對處)해 야 할지를 모르는 여러 기술자(技術者)들에게 도움이 되었으면 하는 것이다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.7
• /
• pp.310-315
• /
• 2017

Automotive waterproof connectors are highly functional parts that must be air-tight in a complex environment. In the LSR multi-cavity injection molding process for manufacturing waterproof connectors, it is important to maintain a uniform curing temperature between the cavities in order to obtain a quality product. For this purpose, we designed the capacity of the cartridge heater differently for each position, and then linked the heat transfer analysis and optimization module to obtain the optimal cartridge heater capacity. As a result of the optimization analysis, the temperature deviation between cavities was decreased from $13.1^{\circ}C$ to $8.1^{\circ}C$ compared with the case in which constant heater capacity was applied, so that the design criterion could be satisfied within a temperature deviation of $10^{\circ}C$ for uniform curing. This study suggests that this method can be applied efficiently to the design of a large area multi-cavity LSR mold heater.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.5352-5356
• /
• 2013

Plastic product manufacturing industry has usually focused on a mechanical and physical characteristics of molding. Recently, not only these characteristics but also the aesthetic value is significantly considering. Especially, the molding's gloss, which we can easily distinguish, is an important aesthetic point. In this study, it were investigated that the gloss variation of ABS moldings by changing injection conditions such as injection pressures, injection speed, holding pressures melt and mold temperatures by injection molding experiment. The experimental results revealed that the holding pressure was the most active condition on gloss of ABS molding.

• Design & Manufacturing
• /
• v.17 no.1
• /
• pp.1-5
• /
• 2023

In multi-material injection molding, since two or more materials with different process conditions are used, it is essential to maximize process efficiency by operating the cooling or heating system to a minimum. In this study, Liquid silicone rubber (LSR) that can be cured at a low temperature suitable for the multi-material injection molding was selected and the cure behavior according to the process conditions was analyzed through differential scanning calorimetry (DSC). Dynamic measurement results of DSC with different heating rate were obtained, and through this, the total heat of reaction when the LSR was completely cured was calculated. Isothermal measurement results of DSC were derived for 60 minutes at each temperature from 80 ℃ to 110 ℃ at 10 ℃ intervals, and the final degree of cure at each temperature was calculated based on the total heat of reaction identified from the Dynamic DSC measurement results. As the result, it was found that when the temperature is lowered, the curing start time and the time required for the curing reaction increase, but at a temperature of 90 ℃ or higher, LSR can secure a degree of cure of 80% or more. However, at 80 ℃., it was found that not only had a relatively low degree of curing of about 60%, but also significantly increased the curing start time. In addition, in the case of 110 ℃, the parameters were derived from experimental result using the Kamal kinetic model.

• Design & Manufacturing
• /
• v.17 no.2
• /
• pp.27-32
• /
• 2023

Liquid silicon rubber (LSR) has fine thermal compatibility and is widely used in various fields such as medical care and automobiles because it is easy to implement products with good fluidity. With the recent development of flexible sensors, the focus has been on manufacturing conductive elastomers, such as silicone as elastic materials, and carbon black, CNT, and graphene are mainly used as nanomaterials that impart conductive phases. In this study, mechanical behavior and curing behavior were measured and analyzed to manufacture a CB-LSR complex by adding Carbon Black to LSR and to identify properties. As a result of the compression test, the elastic modulus tended to increase as carbon black was added. When the swelling test and the compression set test were conducted, the swelling rate tended to decrease as the content of carbon black increased, and the compression set tended to increase. In addition, DSC measurements showed that the total amount of reaction heat increased slightly as the carbon black content increased. It is considered that carbon black was involved in the crosslinking of LSR to increase the crosslinking density and have a positive effect on oil resistance reinforcement.

• Korean Chemical Engineering Research
• /
• v.49 no.1
• /
• pp.47-55
• /
• 2011

The optimum mold design and the optimum process condition were constructed upon executing process simulation of rubber injection molding with the commercial CAE program of MOLDFLOW (Ver. 5.2) in order to solve the process-problems of K company relating to cracks, which occurs at the inner cavity wall of C. V. joint boots. As a result it was confirmed that the real cracks occurs at the exactly same position of the cavity as exhibits the defects of weld and meld line and unsatisfactory curing according to the result of simulation. In order to prevent the occurrence of weld and meld line at the defect-position, the location of gate was altered to the optimum position of the cavity. Consequently the filling pattern was established to minimize the degree of the melt-fronts confronting or the melt-flows melding to prevent the occurrence of weld and meld line at the defect-position. It was observed that both gate-positions to maximize the degree of the formation of weld and meld line and air traps are located, respectively, in opposite direction each other with reference to the optimum gate position. In addition, the temperature of mold was raised by $10^{\circ}C$ and maintained at $170^{\circ}C$ for satisfactory curing.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.391-396
• /
• 2009

This paper presents the numerical analysis of thread rolling. Firstly, the analysis is focused on the effective analysis conditions that guarantee the reliability of the analysis results. The investigated parameters are the number of teeth and the number of elements. Using the analysis results, the number of elements and the number of teeth that guarantee the results are found. And then, the effects of the process parameters such as tool shape and temperature on the thread rolling are investigated. The analysis is carried out using DEFORM-3D. The results show that the flank angle and crest round have an effect on the thread rolling load. It is also shown that temperature have significant effects on the effective strain distribution, rolling load, and crack initiation. The crack initiation is predicted using the Cockcroft-Latham criterion.