• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.309-316
• /
• 2016

In this study, performance of hardening accelerator types which promote setting and hardening of cement has been reviewed in order to develop early age strength of concrete with compressive strength of 21~27 MPa after examination of strength development of the concrete at early age according to curing temperature and unit cement(binder) content. As results, soluble mineral salt showed better hardening acceleration effect than organic salt in the scope of this study. Also, hydration reaction accelerating effect of $C_3S$ by Soluble mineral salt is effective on development of early age compressive strength and it was shown that the Pt's hydration reaction accelerating effect was the best. Construction duration reduction can be expected by securing compressive strength for prevention of early aged freezing damage in 25hour-curing time under curing temperature at $15^{\circ}C$. Also, it was shown that compressive strength of specimen cured at $5^{\circ}C$ was similar with plain specimen cured at $10^{\circ}C$. Therefore, it is expected that fuel costs and carbon dioxide can be reduced when the same construction duration is considered.

• Journal of the Korean Wood Science and Technology
• /
• v.42 no.3
• /
• pp.339-345
• /
• 2014

For enhancing productivity of glulam, high frequency (HF) curing technique was researched in this study. Heat energy is generated by electromagnetic energy dissipation when HF wave is applied to a dielectric material. Because both lamina and adhesives have dielectric property, internal heat generation would be occurred when HF wave is applied to glulam. Most room temperature setting adhesives such as phenol-resorcinol-formaldehyde (PRF) resin, which is popularly used for manufacturing glulam, can be cured more quickly as temperature of adhesives increases. In this study, dielectric properties of larch wood and PRF adhesives were experimentally evaluated, and the mechanism of HF heating, which induced the fast curing of glue layer in glulam, was theoretically analyzed. Result of our experiments showed relative loss factor of PRF resin, which leads temperature increase, was higher than that of larch wood. Also, it showed density and specific heat of PRF, which are resistance factors of temperature increase, were higher than those of wood. It was expected that the heat generation in PRF resin by HF heating would occur greater than in larch wood, because the ratio of relative loss factor to density and specific heat of PRF resin was greater than that of larch wood. Through theoretical approach with the experimental results, the relative strengths of ISM band HF electric fields to achieve a target heating rate were estimated.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.5
• /
• pp.409-417
• /
• 2003

Cure monitoring can be used to improve the quality and productivity of thermosetting resin matrix composite products during their manufacturing process. In this work, the sensitivity of dielectrometry was improved by adequate separation the efforts of sensor and externals on the measured signal. A new algorithm to obtain the degree of cure during dielectric cure monitoring of glass/polyester and glass/epoxy composites was developed by employing a function of both temperature and dissipation factor, in which five cure monitoring parameters were used to calculate the degree of cure. The decreasing pattern of dissipation factor was compared with the relationships between the degree of cure and the resin viscosity. The developed algorithm might be employed for the in situ cure monitoring of thermosetting resin composites.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.88-97
• /
• 2002

The effect of aminosiloxane modifier on the chemorheological properties of ortho-cresol novolac epoxy/phenol novelac/triphnylphosphine resin system was investigated aat different isothermal curing temperatures. By adding the aminosiloxane to the resin system, not only conversion rate and conversion were increased but also glass transition temperature was promoted. Critical conversion and gelation time obtained at the crossover point between storage and loss moduli were reduced and thus the viscosity was increased by the aminosiloxane. $C_1$ and $C_2$ in the WLF equation calculated from the glass transition temperature as a function of conversion and measured viscosity were found to vary with the curing temperature. By applying the change of glass transition temperature with conversion, $C_1$ and $C_2$ to WLF equation, it was possible to predict accurately the viscosity change with isothermal curing reaction.

• Journal of Adhesion and Interface
• /
• v.10 no.3
• /
• pp.117-126
• /
• 2009

Epoxy/anhydride systems with silica filler were studied to improve the cure behavior and characteristics. To study the curing process of epoxy/anhydride using DSC and a stress rheometer, it was observed that gelation temperature increased by increasing the thermal rate or in high isothermal conditions, while it was observed that the degree of cure at gelation decreased. Thermal stability of the epoxy/anhydride system showed any increment by increasing silica contents, except slight decrease of weight by containing humidity. The epoxy resin cured with 30% of silica filler decreased coefficient thermal expansion (CTE) about 33% to show $40ppm/^{\circ}C$. Specimens filled with 30 wt% of silica showed 60% increase in storage modulus at $30^{\circ}C$ to show 3909 MPa compared with neat resin to 2,377 MPa. Epoxy/anhydride systems with surface treated silica by silane coupling agent decreased storage modulus.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.6
• /
• pp.278-285
• /
• 2006

Coating mixtures of the resin B-H for the application to the desulfurization system of power plant were coated on carbon steels and cured at the temperature of $65^{\circ}C{\sim}80^{\circ}C$. After being contacted with 70wt% $H_2SO_4$ solution of $100^{\circ}C\;and\;120^{\circ}C$ for several hours, their composition, Vicker's hardness and microstructures by SEM were examined. Corrosion resistance of the coating mixtures to $H_2SO_4$ solution was related to the content of $SO_3$ in the coated specimens after corrosion test. The lower curing temperature and the shorter curing time the coated specimens went through, the higher corrosion resistance to acid they showed, but the more cracks were developed at higher temperature. It was realized that the corrosion resistance to sulfaric acid solution was increased on the condition of curing temperature above $65^{\circ}C$ and curing time above 12 hours at least.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.39.2-39.2
• /
• 2011

7075알루미늄 합금은 기계적 강도가 가장 높은 고강도 합금으로 열처리 공정이 반드시 필요하다. 그러나 열처리 공정 중 재료의 두께에 따른 내부 온도의 차이로 인한 잔류응력이 발생하여 최종 제품의 치수에 변화를 일으켜 제품 생산에 어려움이 있다. 따라서 본 연구에서 극저온 열처리 공정을 통하여 야기되는 7075알루미늄 합금의 기계적 특성 및 미세조직에 관하여 연구하였다. 7075 알루미늄 합금은 석출경화를 통한 강화가 이루어지며, 석출경화를 위해서 용체화 처리를 하여 인공시효를 하는 기존 공정과 비교하여 극저온 열처리 공정은 두 개의 추가적인 단계를 가지고 있다. 첫 번째 단계는 -196도의 액체 질소 속에 샘플을 극저온 ��칭을 하는 단계이고, 두 번째 단계는 샘플의 온도를 급격하게 올리는 up-hill quenching이다. 잔류응력은 X-ray diffraction을 이용한 $sin2{\psi}$ 방법으로 측정되었다. 극저온 열처리 후 기계적 특성을 평가하기 위하여 vickers hardness를 측정하였으며 미세 조직의 특성을 파악하기 위하여 EBSD와 TEM을 이용하여 평가하였다.

• Magazine of the Korea Concrete Institute
• /
• v.2 no.1
• /
• pp.109-119
• /
• 1990

This study was accomplished to investigate the characteristics of hardening shrinkage and initial creep of epoxy resin concrete depending on the presence of filler. According to the test results, the hardening shrinkage was increased with increment of sLOrage temperature, and the ef¬feel of tempemture on the hardening shrinkage of epoxy resin concrete with 6% filler was more Significant than that of epoxy resin concrete without filler. Also, the initial creep strain was increased with loading times, stress--strength ratio and elastic strain, and the values for opoxy resin concrete with 6 % filler are higher than that for eposy resin concrete without filler.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.49-52
• /
• 2006

Epoxy resin has less reaction shrinkage, has better water proofing and thermal resistance than other repairing materials, to it has been applied broadly to repair and finish buildings and infrastructures. Although the ambient temperature constructed is varied with the seasons and epoxy resin has to mix with appropriate hardener due to the non self-hardening, as the real construction of it, the ambient temperature is ignored and the blending ration of epoxy resin and hardener is fixed. Also, because of the hardening time is aimed to temperature condition and the tolerance of blending ratio, we investigated the variation of viscosity according to ambient temperatures and hardener ratios. As a results of study, we can select the economical blending ratio of the epoxy resin and hardener according to site situation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.65-68
• /
• 2007

저온 플라즈마 기술을 이용하면 오스테나이트계 스테인리스강의 내식성과 표면경도를 동시에 증가 시킬 수 있다. 여러 가지 처리방법 중 질탄화와 2-step 공정으로 처리한 AISI304L강의 표면을 분석하였다. 처리한 모든 시편의 표면은 expanded austenite(${\gamma}_N$)이 형성되었고, 표면 경도도 모재보다 약 4배 이상 증가 하였다. 저온플라즈마 질탄화 공정의 경우 경화층의 두께가 최대 15 ${\mu}m$밖에 형성되지 않았지만 2-step공정의 경우 질탄화 공정보다 짧은 시간으로 약 2배의 경화층을 얻을 수 있었다. 두 가지 공정 모두 온도와 시간이 증가할수록 경화층의 두께가 두꺼워졌지만, 과도하게 높은 온도와 긴 공정시간은 석출물을 형성 시켰다. 석출물이 형성되지 않은 시편의 경우 내식성이 증가하였다.