• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.1321-1327
• /
• 2006

This paper presents the calculation of unbalanced magnetic pull (UMP) that causes rotor misalignment in induction motor. The excessive noise and vibration will be occurred by means of rotor misalignment. Angular misalignment of rotor will produce air-gap permeance wave which is function of axial and circumferential coordinate. In this paper, the UMP is calculated using permeance and magneto motive force (MMF) in the case of static and dynamic misalignment. Based on the percentage of misalignment, the result shows that the UMP and magnetic pressure are increased according to the increasing of misalignment. The UMP is occurred not only in It frequency component but also the others.

• International Journal of Highway Engineering
• /
• v.9 no.2 s.32
• /
• pp.27-37
• /
• 2007

This research was conducted to determine the optimum lifting positions on precast concrete slabs for precast concrete pavement construction, based on the analysis of concrete stress distribution under various lifting conditions. To analyze stresses in concrete slabs, the finite element method was implemented and a numerical model of the precast slab that was going to be used in the experimental construction was developed. Changes in the stress distribution due to the lifting angle were investigated because slab lifting is not always performed in the perpendicular direction to the slab surface. In addition, the effect of the lifting level, the distance between the neutral axis of the slab and the lifting point, on the stress distribution was investigated since the lifting point is not always at the neutral axis of the slab. To consider the actual steel design of the precast slab, the effect of the reinforcement near the lifting point was also investigated. From this study, the optimum lifting positions of the precast slabs were determined according to the lifting angle and level, and the results were compared with the lifting positions used in the PCI standards.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1079-1086
• /
• 1990

Recently, demand for the experimental analysis of crack, such as arbitrary or distributed ones which has been considered quite difficult to investigate by the theoretical and numerical method, is increasing. Among existent experimental methods applied to the analysis of stress intensity factors, the slab analogy method have the following merits; cracks can be replaced by similarity-shaped rigid body, and the distribution of stress is represented by slab curvature of duly bent specimen. For the accuracy improvement of this method, multi-point selection method was introduced and its accuracy proved by applying this method to the analysis of centrally linear and inclined cracks in a finite plate which are theoretically known. In this paper, moreover, the stress intensity factors of eccentric and skew-symmetric bent cracks were determined by multi-point selection method and newly developed moire tilted master grating method. The results obtained by this method showed good agreement with the reliably theoretical solutions.

• Korean Journal of Optics and Photonics
• /
• v.32 no.6
• /
• pp.296-305
• /
• 2021

This paper reports a study on the long axis performance of the line beam optics used in laser lift-off equipment for the OLED manufacturing process. The centration errors of the cylindrical lens are classified and defined in seven categories, and the measurement methods are presented. The cylindrical fly-eye lens is analyzed theoretically and experimentally to find the influence of the surface shape error and decentering error on the long axis performance of the line beam optics system. A future research direction is also presented to improve the long axis performance.

• Journal of the Korea Concrete Institute
• /
• v.15 no.5
• /
• pp.679-688
• /
• 2003

For box girders in which the longitudinal tendon is profiled in the inclined webs, longitudinal prestressing force will induce transverse effects as well as longitudinal ones. In this paper, the method to estimate transverse effects induced by longitudinal prestressing is proposed. The concept of transverse equivalent loading which is calculated through longitudinal prestressing analysis is developed. The transverse stress in slabs of box girders due to longitudinal prestressing are investigated. The comparison of numerical results of the proposed method and those of folded plate method represents that the method is reasonable. Numerical analyses are carried out depending on the parameters such as web inclination and ratio of girder length to tendon eccentricity. Analysis results show that when only prestressing are considered the magnitude of transverse stress in slabs of box girder is not so large. However, if the other stresses due to dead and live load et al. are superposed on these stresses, it may be that the longitudinal prestressing effects are significant.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2613-2615
• /
• 2004

본 논문에서는 광학 디스크 기기의 주기적인 외란인 편심 보상을 위해 웨이블릿 신경 회로망 기반 외란 모델로 구성된 순방향 오차 제거(feedforward error rejection) 방법을 제안한다. 신호 모델링 방법으로 사용되어진 신경 회로망 모델의 단점인 실시간 처리 능력 및 국부 최소치로의 가능성 등을 극복하며 주파수와 시간 영역에서의 우수한 신호 해석 능력을 가진 웨이블릿 변환의 장점을 가진 웨이블릿 신경 회로망을 이용하여 디스크의 외란을 모델링 한다. 웨이블릿 신경회로망은 경사 강하법 (gradient descent method)을 이용하여 학습하며, 본 논문에서 제안한 방법의 효율성을 검증하기 위해 실제 광학 디스크 기기의 외란 데이터를 이용한 컴퓨터 모의 실험을 수행한다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.1
• /
• pp.18-23
• /
• 1985

In the fracture mechanics, the determination of the stress intensity factor value is vital for the prediction of a material fracture behavior. So many data concerning to the S.I.F. have been presented by many investigations to meet endless requrement. In this paper, the stress intensity factors of a sheet with an eccentrically inclined crack subjected to the pure bending moment were investigated theoretically by using of the complex mapping function to determine the Muskelishvili's comlex stress functions. Moreover, the theoretical value was compared with the result obtained from photoelastic esperiment. As a result, it was confirmed that both values coincided with satisfactorily within the margin of 2-3% devition; The results theoretically derived are right.

• Journal of Korean Ophthalmic Optics Society
• /
• v.11 no.2
• /
• pp.77-83
• /
• 2006

We have studied the astigmatism according to the bevel position and the tilting(pantoscopic) angle of decentered spectacle lens for prism prescription. For prism prescription, generally we make a general spectacle lens into decentered spectacle lens. At this time the bevel position of decentered lens is a important matter, because the difference between optic axis and visual axis occur aberrations. Using the calculation we find that the case that the axis of bevel rotation band passes the front curvature center of (+) lens has a smaller astigmatism than the case that the axis of bevel rotation band passes the rear curvature center of (+) lens and that the case that the axis of bevel rotation band passes the rear curvature center of (-) lens has a smaller astigmatism than the case that the axis of bevel rotation band passes the front curvature center of (-) lens. We find the lens with higher refraction index has a smaller astigmatism.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.4
• /
• pp.482-488
• /
• 2018

Generally, after stern tube bearing shows a significant increase in local load due to propeller load, which increases the potential adverse effects of bearing failure. To prevent this, research on regarding shaft alignment has been carried out with a focus on reducing the relative slope between the shaft and support bearing(s) under quasi-static conditions. However, for a more detailed evaluation of a shafting system, it is necessary to consider dynamic conditions. In this context, the results revealed that eccentric propeller force under transient conditions such as a rapid rudder turn at NCR, lead to fluid-induced instability and imbalanced vibration in the stern tube. In addition, compared with NCR condition, it has been confirmed that eccentric propeller forces given a rapid rudder starboard turn can lift a shaft from the stern tube bearing in the stern tube, contributes to load relief for the stern tube bearing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.435-442
• /
• 2017

A catadioptric optical system produces images by refraction and reflection. To improve the image quality, the shape of the secondary mirror supporters should be determined to ensure that the centering error and tilt of secondary mirror are very small, and the main mirror receives the maximum amount of light. Furthermore, random acceleration vibration has a severe effect on the optical system for observation reconnaissance. In order to obtain the best design under these circumstances, the volume of the secondary mirror supporter must be minimized while satisfying the constraints expressed in standard deviations of the centering error and tilt. It is difficult to analytically calculate the design sensitivities of the standard deviations, because they are statistically defined. Hence, after their second-order regression equations were determined using a response surface methodology, an optimal geometric design was obtained. As a result, it was found that the method proposed in this paper, which included a random vibration analysis, was effective in obtaining the optimal design for a secondary mirror supporter with robustness.