• Proceedings of the Materials Research Society of Korea Conference
• /
• 2000.11a
• /
• pp.145-145
• /
• 2000

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2000.11a
• /
• pp.160-160
• /
• 2000

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.05a
• /
• pp.104-104
• /
• 1996

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.05a
• /
• pp.52-52
• /
• 1996

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.126.1-126
• /
• 2002

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.26.2-26
• /
• 2002

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.12-12
• /
• 1993

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.9
• /
• pp.953-958
• /
• 2014

The use of functionally graded materials (FGMs) may enhance thermal conductivity without reducing the desired strength in many applications such as injection molds embedding conformal cooling channels and cutting tools with heat sinks (or cooling devices). As a fundamental study for cutting tools having FGM heat sinks between M2 tool steel and Cu, six FGM specimens (M2 and Cu powders were premixed such that the relative compositions of M2 and Cu were 100:0, 80:20, 60:40, 40:60, 20:80, and 0:100 wt%) were fabricated by powder metallurgy in this study. The cross sections of these specimens were observed by optical microscopy, and then the material properties (such as thermal conductivity, specific heat, and coefficient of thermal expansion) related to heat transfer were measured and analyzed.

• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.70-78
• /
• 1997

3Y-TZP/SUS316 Functionally Graded Material (FGM) was fabricated by slip casting method. Alumina mold was used to overcome problems of gypsum mold in slip casting process, and the optimal dispersion con-ditions of 3Y-TZP/SUS316 binary slurries was determined using electrokinetic sonic amplitude and a viscometer, and observing sedimentation behavior. The properties of the specimens casted by gypsum mold and alumina mold were compared in terms of changes in shrinkage rate, drying and sintering conditions, and microstructure. It was found that the specimens obtaine from the alumina mold showed a clean surface, easier thickness control of each layer, and higher productivity. Especially, no degradation was observed in the SUS316 prepared using alumina mold. Thus it is desirable to use porous alumina mold rather than gyp-sum mold for the slip casting of 3Y-TZP/SUS316-FGM.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1184-1188
• /
• 2007

하수관거는 장기간 사용에 의해 오염물질 퇴적 현상이 발생하여 관거 유하능력의 기능을 상실하게 되는 문제점이 발생한다. 관내 오염물질 제거 방법 중 관거 Flushing 방법을 적용하였을 경우, 유입유량, 유입시간, 관경사 변화에 따른 유속 및 수위 변화를 분석하여 하수관거 내 부유물질의 퇴적을 방지하기 위한 최소유속기준을 만족하는 관거 유하 길이를 분석하고자 한다. 관거 내의 수리학적 거동을 분석하기 위해서 SWMM 및 FLOW-3D 모형을 이용하여 관거 내 수리학적 거동 현상을 분석하였다. 또한 모형의 적용성을 검증하기 위해서 수리모형실험 자료를 이용하였다. $5\;{\textperthousand}$ 관경사에 대하여 유입유량 $0.16\;m^3/min$을 3 분 동안 Flushing 하였을 경우 최대유속은 0.58 m/s로 최소유속 0.6 m/s를 만족하는 관의 누가거리는 확보할 수 없는 것으로 모의되었다. 또한 관경사가 증가함에 따라서 최대유속 및 최대유량도 증가함을 보여주고 있다. 이와 같은 분석을 통해 관 내 부유물질의 퇴적을 방지하기 위해 Flushing 방법을 수행하였을 경우, 보다 효과적이며 경제적으로 Flushing 방법을 수행할 수는 설계 자료를 제공할 수 있을 것으로 기대된다.